BS IEC 61196-9-1-2015 Coaxial communication cables Flexible RF coaxial cables Blank detail specification《同轴通信电缆 柔性射频同轴电缆 空白详细规范》.pdf

《BS IEC 61196-9-1-2015 Coaxial communication cables Flexible RF coaxial cables Blank detail specification《同轴通信电缆 柔性射频同轴电缆 空白详细规范》.pdf》由会员分享，可在线阅读，更多相关《BS IEC 61196-9-1-2015 Coaxial communication cables Flexible RF coaxial cables Blank detail specification《同轴通信电缆 柔性射频同轴电缆 空白详细规范》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationCoaxial communication cablesPart 9-1: Flexible RF coaxial cables Blank detail specificationBS IEC 61196-9-1:2015National forewordThis British Standard is the UK implementation of IEC 61196-9-1:2015.The UK participation in its preparation was entrusted to TechnicalCommittee E

2、PL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Us

3、ers are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 84490 4ICS 33.120.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of

4、 theStandards Policy and Strategy Committee on 31 December 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS IEC 61196-9-1:2015IEC 61196-9-1 Edition 1.0 2015-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Coaxial communication cables Part 9-1: Flexible RF coaxia

5、l cables Blank detail specification Cbles coaxiaux de communication Partie 9-1: Cbles coaxiaux RF souples Spcification particulire cadre INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 33.120.10 ISBN 978-2-8322-3008-4 Registered trademark of the International

6、 Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. BS IEC 61196-9-1:2015 2 IE

7、C 61196-9-1:2015 IEC 2015 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Guidance for the preparation of detail specifications 5 4 Blank detail specification . 6 Annex A (normative) Maximum attenuation 11 Bibliography 12 Table A.1 Maximum attenuation . 11 BS IEC 61196-9-1:2015IEC 61196-9

8、-1:2015 IEC 2015 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ COAXIAL COMMUNICATION CABLES Part 9-1: Flexible RF coaxial cables Blank detail specification FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrot

9、echnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specificati

10、ons, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International,

11、 governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decis

12、ions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for intern

13、ational use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In ord

14、er to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be cle

15、arly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification

16、bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, prop

17、erty damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in

18、this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any

19、 or all such patent rights. International Standard IEC 61196-9-1 has been prepared by subcommittee 46A: Coaxial cables, of IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. The text of this standard is based on the followin

20、g documents: FDIS Report on voting 46A/1271/FDIS 46A/1284/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts o

21、f the IEC 61196 series, under the general title: Coaxial communication cables, can be found on the IEC website. BS IEC 61196-9-1:2015 4 IEC 61196-9-1:2015 IEC 2015 This International Standard is to be used in conjunction with IEC 61196-1:2005 and IEC 61196-9:2014. The committee has decided that the

22、contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS IEC 6119

23、6-9-1:2015IEC 61196-9-1:2015 IEC 2015 5 COAXIAL COMMUNICATION CABLES Part 9-1: Flexible RF coaxial cables Blank detail specification 1 Scope This part of IEC 61196, which is a blank detail specification, applies to RF flexible coaxial communication cables described in IEC 61196-9. This blank detail

24、specification is to be read in conjunction with IEC 61196-1 and IEC 61196-9. It determines the layout and style for detail specification. Detail specifications, based on this blank detail specification, may be prepared by a national organization, a manufacturer or a user. 2 Normative references The

25、following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2

26、-20:2008, Environmental testing Part 2-20: Tests Test T: Test methods for solderability and resistance to soldering heat of devices with leads IEC 61196-1:2005, Coaxial communication cables Part 1: Generic specification General, definitions and requirements IEC 61196-1-314:2006, Coaxial communicatio

27、n cables Part 1-314: Mechanical test methods Test for bending IEC 61196-9:2014, Coaxial communication cables Part 9: Sectional specification for RF flexible cables IEC 62037-1:2012, Passive RF and microwave devices, intermodulation level measurement Part 1: General requirements and measuring methods

28、 NOTE Documents which are needed to achieve the tests according to Clause 4, item 9 or item 10, respectively, are listed in IEC 61196-9. 3 Guidance for the preparation of detail specifications The detail specification shall be written in accordance with the layout of the blank detail specification,

29、which forms part of this standard. When a characteristic does not apply, then na (for not applicable) should be entered in the appropriate space. When a characteristic applies but a specific value is not considered necessary, then ns (for not specified) should be entered in the appropriate space. BS

30、 IEC 61196-9-1:2015 6 IEC 61196-9-1:2015 IEC 2015 The numbers shown in brackets in this and the following pages correspond to the following items of required information, which should be entered in the space provided. 1 Name and address of the organization that has prepared the document 2 IEC docume

31、nt number and date of issue 3 Address of the organization from which the document is available 4 Related documents 5 Any other references to the cable, national reference, trade name, etc. 6 Description of the cable 7 Details of the cable construction 8 Engineering information of the cable, provided

32、 by the manufacturer 9 List of the finished cable characteristics. They are separated into electrical, environmental and mechanical characteristics 10 Reference to the relevant subclause of the sectional specification IEC 61196-9 11 Minimum requirements, the values entered shall meet as a minimum th

33、e requirements of sectional specification IEC 61196-9 12 Relevant requirements 4 Blank detail specification Title 1 Prepared by: 2 Document No.: Issue: Date: 3 Available from: 4 Generic specification IEC 61196-1 Sectional specification IEC 61196-9 5 Additional references: IEC 62037-4, IEC 62230 6 Ca

34、ble description: a) Cable variant b) Inner conductor c) Dielectric d) Outer conductor e) Sheath BS IEC 61196-9-1:2015IEC 61196-9-1:2015 IEC 2015 7 7 Cable construction a) Inner conductor Material Diameter (mm) nominal Tolerance (mm): b) Dielectric Material Diameter (mm) nominal Tolerance (mm): c) Ou

35、ter conductor Material Diameter (mm) nominal Tolerance (mm): . Minimum coverage factor of braiding d) Sheath Material Minimum thickness (mm) Diameter (mm) Tolerance (mm): 8 Engineering information (reference only) a) Operational temperature range b) Maximum operating frequency c) Installation temper

36、ature range d) Storage temperature range e) Nominal characteristic impedance f) Maximum continue working voltage g) Minimum bending radius (static state) h) Minimum bending radius (dynamic state) i) Nominal weight j) Power rating 9 Parameter 10 IEC 61196-9:2014 Subclause 11 Value 12 Requirements Ele

37、ctrical characteristics 7.1 Continuity 7.1.1.1 pass Conductor resistance inner 7.1.1.2 /m at 20 C Conductor resistance outer 7.1.1.3 /m at 20 C Insulation resistance 7.1.1.4 Mkm 1 000 Mkm, according to IEC 61196-9 Withstand voltage of dielectric 7.1.1.5 kV rms 40 Hz 60 Hz Withstand voltage of sheath

38、 a7.1.1.6 kV rms 40 Hz 60 Hz Spark test (in-process inspection) a7.1.1.7 kV rms 40 Hz 60 Hz Capacitance 7.1.1.8 pF/m Inductance 7.1.1.9 mH/m BS IEC 61196-9-1:2015 8 IEC 61196-9-1:2015 IEC 2015 9 Parameter 10 IEC 61196-9:2014 Subclause 11 Value 12 Requirements Mean characteristic impedance 7.1.2.1 20

39、0 MHz Relative propagation velocity (velocity ratio) 7.1.2.2 % to % 200 MHz Return loss 7.1.2.3 at MHz dB Length of specimen: m If necessary, refer to a table or graph at the end of the detail specification Attenuation 7.1.2.4 at MHz dB/100m at 20 C If necessary, refer to a table or graph at the end

40、 of the detail specification Regularity of impedance 7.1.2.5 Test procedure: Regularity 40 dB Resp 1% PIM 7.1.2.6 dBm f1= MHz bf2= MHz bInput power: W Only applicable to 50 cable variants RF power rating 7.1.2.7 W Phase variation with temperature 7.1.2.8 Frequency: Phase variation PPM Phase stabilit

41、y with mechanic 7.1.2.9 according to the detail spec. Transfer impedance 7.1.2.10 MHz to MHz m/m Screening attenuation 7.1.2.11 MHz to MHz dB Environmental characteristics 7.2 Cold bend performance 7.2.1 Test method: Diameter: mm Temperature: C Return loss: dB Water penetration 7.2.2 When required,

42、in accordance with the relevant detail specification Climatic sequence 7.2.3 Ta= C Tb= C t1= h Insulation resistance M km Environmental stress 7.2.4 Jacket shall show no evidence of cracking Thermal ageing 7.2.5 Transmission characteristics shall remain within the specified limits BS IEC 61196-9-1:2

43、015IEC 61196-9-1:2015 IEC 2015 9 9 Parameter 10 IEC 61196-9:2014 Subclause 11 Value 12 Requirements Thermal cycling 7.2.6 Transmission characteristics shall remain within the specified limits UV stability 7.2.7 Mechanical characteristics 7.3 Visual examination 7.3.1 No observable defects See IEC 611

44、96-9 Dimensional examination 7.3.2 Dimensions according to the detail specification. Ovality of the dielectric 7.3.3 % Ovality of the sheath 7.3.4 % Eccentricity of dielectric 7.3.5 % Eccentricity of the sheath 7.3.6 % Carbon black content 7.3.7 Adhesion testing 7.3.8 Minimum N Maximum N Length:( )

45、mm Length = ( ) mm c d Bending 7.3.9 Maximum allowable attenuation increase L = mm Room temperature Mass: ( ) g Solderability 7.3.13 Dimensional shrinkage mm IEC 60068-2-20 Test Tb T = (260 3) C, L = mm t = s, l = mm BS IEC 61196-9-1:2015 10 IEC 61196-9-1:2015 IEC 2015 9 Parameter 10 IEC 61196-9:201

46、4 Subclause 11 Value 12 Requirements Fire performance 7.4 Flame propagation 7.4.1 Halogen acid gas emission 7.4.2 Toxic gas emission 7.4.3 Smoke density 7.4.4 Key na = not applicable. aOne of these tests can be selected. The other shall mark “na”. bFrequencies are not always spot values, and can be

47、swept over a range. The test procedures for swept and fixed frequencies are described in Annex B of IEC 62037-1:2012. c The adhesion of the dielectric to the inner conductor, Fa, is given in MPa by the following equation: ldFF=awhere F is the force, d is the diameter of inner conductor, l is the len

48、gth of the sample. dOther values may be required if special tools for preparing connector mounting are used (see relevant detail specification). Limits should be given in the detail specification. BS IEC 61196-9-1:2015IEC 61196-9-1:2015 IEC 2015 11 Annex A (normative) Maximum attenuation If necessary, a table according to Table A.1 with attenuation values at certain frequencies at the end of the detail specification shall be given. A graph with attenuation values