BS IEC 61196-1-114-2015 Coaxial communication cables Electrical test methods Test for inductance《同轴通信电缆 电气试验方法 电感测试》.pdf

《BS IEC 61196-1-114-2015 Coaxial communication cables Electrical test methods Test for inductance《同轴通信电缆 电气试验方法 电感测试》.pdf》由会员分享，可在线阅读，更多相关《BS IEC 61196-1-114-2015 Coaxial communication cables Electrical test methods Test for inductance《同轴通信电缆 电气试验方法 电感测试》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationCoaxial communication cablesPart 1114. Electrical test methods Test for inductanceBS IEC 61196-1-114:2015National forewordThis British Standard is the UK implementation of IEC 61196-1-114:2015.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/46

2、, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users a

3、re responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 91936 7ICS 33.120.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theS

4、tandards Policy and Strategy Committee on 31 October 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS IEC 61196-1-114:2015IEC 61196-1-114 Edition 1.0 2015-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Coaxial communication cables Part 1-114: Electrical test me

5、thods Test for inductance Cbles coaxiaux de communication Partie 1-114: Mthodes dessais lectriques Essai dinductance INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 33.120.10 ISBN 978-2-8322-2935-4 Registered trademark of the International Electrotechnical Co

6、mmission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. BS IEC 61196-1-114:2015 2 IEC 61196-1-114:2015

7、 IEC 2015 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references . 5 3 Terms and definitions. 5 4 Procedure 6 4.1 Equipment . 6 4.2 Test sample 6 4.3 Calibration 6 4.4 Test set-up 6 4.5 Measuring procedure . 6 5 Expression of test results . 6 6 Test report . 7 BS IEC 61196-1-114:2015 4 IEC 61196-1-1

8、14:2015 IEC 2015 This standard is intended to be read in conjunction with IEC 61196-1. It is based on the second edition (2005) of that standard. A list of all the parts in the IEC 61196 series published under the general title Coaxial communication cables can be found on the IEC website. The commit

9、tee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised editio

10、n, or amended. BS IEC 61196-1-114:2015IEC 61196-1-114:2015 IEC 2015 5 COAXIAL COMMUNICATION CABLES Part 1-114: Electrical test methods Test for inductance 1 Scope This part of IEC 61196 details the test methods to determine the inductance characteristics of coaxial cables used in analogue and digita

11、l communication systems. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

12、ment (including any amendments) applies. IEC 61196-1, Coaxial communication cables Part 1: Generic specification General, definitions and requirements IEC 61196-1-101, Coaxial communication cables Part 1-101: Electrical test methods Test for conductor d.c. resistance of cable 3 Terms and definitions

13、 For the purposes of this document, the terms and definitions given in IEC 61196-1 as well as the following apply. 3.1 inductance effective inductance (L) of the cable as the sum of the inductances of the inner conductor, the outer conductor and the mutual inductance between the two conductors Note

14、1 to entry: At any (low) frequency, the impedance of a cable can be represented by two components resistance (R) and reactance (X) or as a polar function having magnitude (Z) and phase (). The impedance shall be represented by a series circuit: R = Z cos () and X = Z sin () where Z = (R2+ X2); tan (

15、) = X/R; X = 2fL. Note 2 to entry: Inductances normally are measured at low frequencies (f) (50 Hz, 800 Hz or 1 000 Hz) as required in the relevant cable specification. For this case, the DC resistance (R) shall be measured as described in IEC 61196-1-101. R is the DC-resistance of the inner and out

16、er conductor (= loop resistance). BS IEC 61196-1-114:2015 6 IEC 61196-1-114:2015 IEC 2015 4 Procedure 4.1 Equipment The measurements can be performed using an impedance analyser (or alternatively a discrete signal generator and receiver), an LCR-meter or an impedance-measuring-bridge (Wheatstone-, M

17、axwell-Bridge). Accuracy of measuring equipment should be less than or equal to 2 %. 4.2 Test sample The test sample shall be straightened and have a length of 10 m up to 100 m. The test may be performed at a delivery length, if the attenuation of the cable is small enough, but less than 1/20 of the

18、 wave length of the test signal for measurement with higher frequencies. 4.3 Calibration The influence of the connecting cables, used for connection of the CUT to the equipment, shall be measured at the relevant frequency. The calibration of the test set-up with the impedance analyser shall be done

19、under open, short and load conditions. The measurements shall be done over the whole specified frequency range. The calibration data shall be saved, so that the results may be corrected. 4.4 Test set-up The input impedance Z of the CUT shall be measured with the impedance analyser with a short circu

20、it at the far end of the end of the CUT. 4.5 Measuring procedure The test sample shall be connected to the terminals of the measuring devices and the impedance Z shall be measured with a short circuit at the far end of the CUT. Impedance analysers or LCR-meters will show the value of inductance dire

21、ctly. In other cases, the equation given in 3.1 can be used to calculate the inductance with other instrumentation. 5 Expression of test results The test results shall be normalized to the reference length of 1 km. L = (Lm/Length) 1 000 (mH/km) where L is the inductance of reference length; Lmis the

22、 measured inductance in millihenrys; Length is the length of sample in metres. BS IEC 61196-1-114:2015IEC 61196-1-114:2015 IEC 2015 7 6 Test report The test report shall give the test conditions: temperature, test frequency, sample length, normalized values for the reference length. type equipment u

23、sed and record the corrected values for the reference length. _ BS IEC 61196-1-114:2015This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. Britis

24、h Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined exp

25、erience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Inf

26、ormation on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications

27、, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Subscripti

28、onsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop.

29、Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating serv

30、ice exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to

31、host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by

32、 amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in

33、all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. E

34、xcept as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained fr

35、om the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW