BS IEC 61010-3-1997 Safety requirements for electrical equipment for measurement control and laboratory use - Protocol for the preparation of conformity verification reports for th.pdf

《BS IEC 61010-3-1997 Safety requirements for electrical equipment for measurement control and laboratory use - Protocol for the preparation of conformity verification reports for th.pdf》由会员分享，可在线阅读，更多相关《BS IEC 61010-3-1997 Safety requirements for electrical equipment for measurement control and laboratory use - Protocol for the preparation of conformity verification reports for th.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS IEC 61010-3:1997 Safety requirements for electrical equipment for measurement, control, and laboratory use Part 3: Protocol for the preparation of conformity verification reports for the IEC 61010 series ICS 17.220.20; 19.080; 71.040.10BSIEC61010-3:1997 This British Standard, hav

2、ing been prepared under the directionof the ElectrotechnicalSector Board, was published under the authorityof the Standards Boardand comes into effect on 15 November 1997 BSI 04-2000 ISBN 0 580 28762 9 National foreword This British Standard reproduces verbatim IEC61010-3:1997-07 and implements it a

3、s the UK national standard. The UK participation in its preparation was entrusted to Technical Committee EPL/66, Safety of measuring, control, and laboratory equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee

4、any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references

5、 The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue.

6、 From 1 January 1997, all IEC publications have the number60000added to the old number. For instance, IEC 27-1 has been renumbered as IEC60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. A British Stan

7、dard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover,

8、 an inside front cover, pagesi andii, theIEC title page, pagesii toiv, pages1 to9 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publicati

9、on Amd. No. Date CommentsBSIEC61010-3:1997 BSI 04-2000 i Contents Page National foreword Inside front cover Foreword iii Text of IEC 61010-3 1ii blankBSIEC61010-3:1997 ii BSI 04-2000 Contents Page Foreword iii 1 Scope 1 2 List of conformity verification reports 1 3 Documents 1 4 Completion of the re

10、port 2 Annex A Example of contents list based on IEC 61010-1 (with amendment 2) for a report on a typical item of laboratory equipment 5 Figure 1 Example of a block diagram for form A.5 based on circuits in Annex E of IEC 61010-1 2 Figure 2 Examples of block diagrams of battery load circuits (see fo

11、rm A.5) 4 Table 1 Example of Table A.5 completed 3BSIEC61010-3:1997 BSI 04-2000 iii Foreword 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is

12、to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Committee in

13、terested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO) in accord

14、ance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all

15、interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical reports or guides and they are accepted by the National Committees in that sense. 4) In order to promote international unification, I

16、EC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. 5) The IE

17、C provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. 6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights.

18、 The IEC shall not be held responsible for identifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. In exceptional circumstances, a technical committee may propose the publication of a technical report of one of the following types:

19、type 1, when the required support cannot be obtained for the publication of an International Standard, despite repeated efforts; type 2, when the subject is still under technical development or where for any other reason there is the future but not immediate possibility of an agreement on an Interna

20、tional Standard; type 3, when a technical committee has collected data of a different kind from that which is normally published as an International Standard, for example “state of the art”. Technical reports of types1and2are subject to review within three years of publication to decide whether they

21、 can be transformed into International Standards. Technical reports of type3do not necessarily have to be reviewed until the data they provide are considered to be no longer valid or useful. IEC 61010-3, which is a technical report of type3, has been prepared by IEC technical committee66: Safety of

22、measuring, control, and laboratory equipment. The text of this technical report is based on the following documents: Full information on the voting for the approval of this technical report can be found in the report on voting indicated in the above table. This report is a Technical Report of type3a

23、nd is of a purely informative nature. It is not to be regarded as an International Standard. Committee draft Report on voting 66/144/CDV 66/164/RVDiv blankBSIEC61010-3:1997 BSI 04-2000 1 1 Scope This part of IEC61010 is a technical report type3, which provides a test protocol for testhouses and othe

24、r users to assist them with determining and recording verification of conformity of the equipment under test with the reference documents identified on the front cover of the appropriate report. 2 List of conformity verification reports The following conformity verification reports should be used wi

25、th the appropriate standard(s). These part2standards indicate in their forewords which amendments to IEC61010-1 are applicable. Requirements which apply only to amendment2to IEC61010-1 are indicated by “(AM2)” in the first column. Requirements deleted by amendment2to IEC61010-1 are indicated by “(AM

26、1 only)” in the second column. a) IEC61010-3-1 for: 1) IEC 61010-1:1990 + amendment 1:1992; or 2) IEC 61010-1:1990 + amendment 1:1992 + amendment 2:1995; b) IEC 61010-3-010 for IEC61010-2-010:1992 + amendment1:1996; c) IEC 61010-3-010 for IEC61010-2-020:1992 + amendment1:1996; d) IEC 61010-3-031 for

27、 IEC61010-2-031: 2nd edition (in preparation); e) IEC 61010-3-032 for IEC61010-2-032:1994; f) IEC 61010-3-041 for IEC61010-2-041:1996; g) IEC 61010-3-042 for IEC61010-2-042:1997; h) IEC 61010-3-043 for IEC61010-2-043:1997; i) IEC 61010-3-045 for IEC61010-2-045: (under consideration); j) IEC 61010-3-

28、051 for IEC61010-2-051:1995; k) IEC 61010-3-061 for IEC61010-2-061:1995; l) IEC 61010-3-071 for IEC61010-2-071: (in preparation); m) IEC 61010-3-081 for IEC61010-2-081: (under consideration). Individual report layouts reflecting the referenced documents are presented for each part of the IEC61010ser

29、ies in the form of a checklist together with forms (where required) for reflecting the results of tests. Key words or phrases of the appropriate standard(s) are mainly used, but in order to understand the full details of the requirements to be met when using a conformity verification report, it is e

30、ssential that test personnel refer to the approriate standards. Where any doubts arise, the requirements of standards take precedence over the text of conformity verification reports. Care should be taken to ensure that any potentially destructive testing is performed last in the sequence of testing

31、, as determined by the tester. Clauses or subclauses which are not applicable need not be included in the prepared report, provided that these omissions are indicated in the contents list of the report. An example of a contents list based on IEC61010-1 is given in Annex A for a report on a specific

32、product. 3 Documents The documents a) to d) together with any others required by the standard should be reviewed and listed in the report: a) general description of the equipment tested; b) OPERATOR instructions; c) installation instruction; d) service instructions. The documents e) to n), if applic

33、able, should also be listed in the report: e) component data sheets and certification details; f) wire data sheets; g) flammability test results or data sheets; h) enclosure flammability test results and/or material data sheets; i) comparative tracking indices of printed wiring board materials; j) d

34、ata sheets, test results or certification details for cathode-ray tubes; k) constructional drawings and specifications for transformers including winding and insulation details;BSIEC61010-3:1997 2 BSI 04-2000 l) test results for abnormal operation and fault conditions; m) layout of printed wiring bo

35、ards with primary and secondary hazardous voltages showing all working voltages on the tracks; n) circuit diagrams, and assembly drawings of printed wiring boards. 4 Completion of the report a) If additional information is required for any part of the report, it should be included on a separate shee

36、t. b) Character F in the clause column indicates that a form must be attached to demonstrate conformity. c) Clause6 Protection against electric shock Block diagram of a system. The table in Form A.5 should be completed and a block diagram included (where possible) to assist analysis of the product.

37、An example of a block diagram and a table is given below. The letters A, B, etc., indicate points between which dielectric strength tests, or measurements of CREEPAGE DISTANCE or CLEARANCE, should be made. c) Subclause13.2.2 Batteries Examples of block diagrams of battery load circuits (see13.2.2 an

38、d form A.24) Figure 1 Example of a block diagram for Form A.5 based on circuits in Annex E of IEC61010-1BSIEC61010-3:1997 BSI 04-2000 3 Table 1 Example of Table A.5 completed POLLUTION DEGREE: 2 INSTALLATION CATEGORY (OVERVOLTAGE CATEGORY): II Location or description Insulation type (note 1) Maximum

39、 working voltage CREEPAGE DISTANCE CLEARANCE Test voltage (note 2) Comments (note 3) PWB CTI Other CTI V mm mm mm V A BI 230 1,5 100 3,0 100 1,5 Not required B BI 230 1,5 100 2,1 400 1,5 1900d.c. C DI/RI 230 3,3 100 6,0 100 3,3 2300r.m.s. D DI 230 3,3 100 6,0 100 3,3 2300r.m.s. E DI 230 3,3 100 3,3

40、600 3,3 2300r.m.s. NOTE 1Type of insulation to be stated: BI = BASIC INSULATION RI = REINFORCED INSULATION DI = DOUBLE INSULATION SI = SUPPLEMENTARY INSULATION PI = PROTECTIVE IMPEDANCE NOTE 2Type of voltage: Peak impulse test voltage (pulse) peak r.m.s. d.c. NOTE 3INSTALLATION (OVERVOLTAGE) CATEGOR

41、IES or POLLUTION DEGREES which differ from these should be shown under “comments”.BSIEC61010-3:1997 4 BSI 04-2000 Figure 2 Examples of block diagrams of battery load circuits (see Form A.5)BSIEC61010-3:1997 BSI 04-2000 5 Annex A Example of a contents list based on IEC 61010-1 (with amendment 2) for

42、a report on a typical item of laboratory equipment NOTEClauses and subclauses with a line through them are not applicable to the product concerned. Summary of tests 4.4 Testing in SINGLE FAULT CONDITION 4.4.2.1 PROTECTIVE IMPEDANCE 4.4.2.2 Protective conductor 4.4.2.3 Equipment or parts for short-te

43、rm or intermittent operations 4.4.2.4 Motors 4.4.2.5 Capacitors 4.4.2.6 Mains transformers 4.4.2.7 Outputs 4.4.2.8 Equipment for more than one supply 4.4.2.9 Cooling 4.4.2.10 Heating devices 4.4.2.11 Insulation between circuits and parts 4.4.2.12 Interlocks 5 Marking and documentation 5.1.1 General

44、5.1.2 Identification 5.1.3 Mains supply 5.1.4 Fuses 5.1.5 Measuring circuits TERMINALS 5.1.6 TERMINALS and operating device 5.1.7 Equipment protected by DOUBLE INSULATION or REINFORCED INSULATION 5.1.8 Battery charging 5.2 Warning markings 5.3 Durability of markings 5.4 Documentation 5.4.1 General 5

45、.4.2 Equipment RATINGS 5.4.3 Equipment installation 5.4.4 Equipment operation 5.4.5 Equipment maintenance 6 Protection against electric shock 6.1 General 6.1.1 Exceptions 6.2 Determination of ACCESSIBLE parts 6.2.1 General examination 6.2.2 Openings above parts which are HAZARDOUS LIVE 6.2.3 Opening

46、s for pro-set controlsBSIEC61010-3:1997 6 BSI 04-2000 6.3 Permissible limits for ACCESSIBLE parts 6.3.1 Values in NORMAL CONDITION 6.3.2 Values in SINGLE FAULT CONDITION 6.3.2.1 Voltage 6.3.2.2 Current 6.3.2.3 Capacitance 6.4 Protection in NORMAL CONDITION 6.5 Protection in SINGLE FAULT CONDITION 6.

47、5.1 Protective earthing 6.5.1.1 PROTECTIVE BONDING 6.5.1.2 Bonding impedance of plug-connected equipment 6.5.1.3 Bonding impedance of PERMANENTLY CONNECTED EQUIPMENT 6.5.1.4 Indirect bonding for measuring and test equipment 6.5.2 DOUBLE INSULATION and REINFORCED INSULATION 6.5.3 PROTECTIVE IMPEDANCE

48、 6.5.4 Built in equipment (AM 1 only) Panel meters (AM 2) 6.6 External circuits 6.6.1 Separation of internal circuits 6.6.2 TERMINALS for external circuits 6.6.3 Circuits with TERMINALS which are HAZARDOUS LIVE 6.7 CLEARANCES and CREEPAGE DISTANCES 6.8 Dielectric strength test 6.8.1 Reference test e

49、arth 6.8.2 Humidity preconditioning 6.8.3 Conduct of tests 6.9 Constructional requirements for protection against electric shock 6.9.1 General 6.9.2 ENCLOSURES of equipment with DOUBLE INSULATION or REINFORCED INSULATION 6.9.3 Equipment using PROTECTIVE BONDING 6.9.4 Over-range indication 6.10 Connection to mains supply source (AM 1 only) Connection to mains supply source and connections between parts of equipment (AM 2) 6.10.1 Mains supply cords 6.10.2 Fitting of non-detachable mains supply cords 6.10.2.1 Cord entry 6.10.2.2 Cord anchorage 6