BS IEC 61010-3-010-1999 Safety requirements for electrical equipment for measurement control and laboratory use - Conformity verification report for IEC 61010-2-010 particular requg.pdf

《BS IEC 61010-3-010-1999 Safety requirements for electrical equipment for measurement control and laboratory use - Conformity verification report for IEC 61010-2-010 particular requg.pdf》由会员分享，可在线阅读，更多相关《BS IEC 61010-3-010-1999 Safety requirements for electrical equipment for measurement control and laboratory use - Conformity verification report for IEC 61010-2-010 particular requg.pdf（64页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 3-010: Conformity verification report for IEC 61010-2-010, Particular requirements for laboratory equipment for the heating of materials ICs 03.120.20: 71.040.20 3s IEC i 10 10-3-0 1 O:

2、1999 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGH LAW BS IEC 610103-0101999 direction of the Electrotechnical Amd. No. Date Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 October 1999 National foreword Comments This Bri

3、tish Standard reproduces verbatim lEC 6101030101999 and implements it as the UK national sandard. The UK participation in its preparation was entrusted to Technical Committee EPU66, Safety requirements for electrical equipment for measurement, control, and laboratory use, which has the responsibilit

4、y to: - aid enquirers to understand the text; - present to the responsible internationalEuropeam committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed - monitor related international and European developments and promulgate them in the UK A list o

5、f organizations represented on this committee can be obtained on request to its secretary. Rom 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as EC 60027-1. For a period of time during the change over from one numbering

6、system to the other, publications may contain identifiers from both systems. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Corr

7、espondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does n

8、ot of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, am inside front cover, the IEC title page, pages 2 to 61 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. O BSI 10-1999 ISBN

9、O 580 32959 3 STD-BSI BS IEC bl10-3-010-ENGL 1997 Lb24bb9 079b453 98T BS IEC 61010-3-010:1999 TECHNICAL REPORT IEC 61 O1 0-3-01 O First edition 1999-02 Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 3-01 O: Conformity verification report for IEC 6101

10、0-2-01 O, Particular requirements for laboratory equipment for the heating of materials Rgles de scurit pour appareils lectriques de mesurage, de rgulation et de laboratoire - Partie 3-01 O: Rapport de verification de la conformit de la CE1 61070-2-010, Prescriptions particulires pour appareils de l

11、aboratoire utiliss pour lchauffement des matires Reference number IEC 61010-3-01 Oz1 999(E) STD-BSI BS IEC bLBO-3-010-ENGL 1999 LbZLfbbS 07Sb!i54 8Bb BS IEC 61010-3-010:1999 CONTENTS Page FOREWORD . 3 Conformity verification report for IEC 61 O1 0-2-01 O . 5 Clause 5 Marking and documentation 10 6 P

12、rotection against electric shock . 16 7 Protection against mechanical hazards . 25 8 Mechanical resistance to shock and impact . 25 9 Equipment temperature limits and protection against the spread of fire 10 Resistance to heat 11 Protection against hazards from fluids . 12 Protection against radiati

13、on. including laser sources. and against sonic and ultrasonic pressure . 13 Protection against liberated gases. explosion and implosion 14 Components . 15 Protection by interlocks . 16 Measuring circuits . Annex K Routine tests . 26 28 28 29 30 31 32 32 32 Tables 1 Documents attached to this report

14、. 7 2 Test equipment list . 8 3 List of components relied on for safety 9 Form A.l to Form A.29 33 to 61 2 - STD=BSI BS IEC bLO10-3-010-ENGL 1777 II lib24bb9 077bY55 752 = BS IEC 61010-3-010:1999 INTERNATIONAL ELECTROTECHNICAL COMMISSION SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT,

15、CONTROL, AND LABORATORY USE - Part 3-01 O: Conformity verification report for IEC 61010-2-01 O, Particular requirements for laboratory equipment for the heating of material FOREWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all

16、national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standar

17、ds. Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC col

18、laborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opi

19、nion on the relevant subjects since each technical committee has representation from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical reports or guides and they are accepted by t

20、he National Committees in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corres

21、ponding national or regional standard shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. 6) Attention is drawn to the possibility that

22、 some of the elements of this International Standard may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. However, a technical committee may propose t

23、he publication of a technical report when it has collected data of a different kind from that which is normally published as an International Standard, for example “state of the art“. Technical reports do not necessarily have to be reviewed until the data they provide are considered to be no longer

24、valid or useful. IEC 61010-3-010, which is a technical report, has been prepared by IEC technical committee 66: Safety of measuring, control, and laboratory equipment. The text of this technical report is based on the following documents: I Enquiry draft I Report on voting I I I _ 66l178lCDV 66/202/

25、RVC Full information on the voting for the approval of this technical report can be found in the report on voting indicated in the above table. This report is a Technical Report and is of a purely informative nature and is therefore by itself not to be regarded as an International Standard. It is fo

26、r use by testhouses and other users to assist them with determining and recording verification of conformity of the equipment under test with the requirements of: IEC 61010-2-010:1992 + amendment 1:1996 The protocol for completion of this report is contained in publication IEC 61010-3:1997. The IEC

27、sells read-only PDF files as a general rule. In the present instance, and quite exceptionally, to enable the user to fill in the forms, a revisable file is included in a pocket affixed to the back cover of this publication. This publication can also be downloaded from the Web as a PDF file. There is

28、, however, at the end of the document, a revisable file containing the forms. Please use the ziphnzip function. 4 - STDmBSI BS IEC bLDLO-3-OLO-ENGL 1999 II Lb29bbS 079b1i57 525 = BS IEC 61010-3-0101999 (including amendment 1 :1996) Report reference No .: Compiled by (+ signature) . : Approved by (+

29、signature) : Date of issue . : Testing organization .: Address . : Testing location . : Applicant . : Address .: Standard . : IEC 61010-1:1990 + A1:1992 + A2:1995 IEC 61010-2-010:1992 + A1:1996 Copyright blank test report . : This report has been prepared by IEC TC 66, which retains responsibility f

30、or any changes or corrections required. Test procedure . : Procedure deviation . : Non-standard test method . .: Type of item tested : c Measurement : Control z Laboratory Trade mark . .: . Modelhype reference . .: Manufacturer : Rating . : Copy of rating plate: I STD-BSI BS IEC bLOLO-3-LO-ENGL 1777

31、 sl Lb24bb7 79b458 4bl M BS IEC 61010-3-010:1999 Description of equipment function . : lNSTALLATiON/OVERVOLTAGE CATEGORY . : POLLUTION DEGREE: Environmental rating: 7 Standard c Other (specify): Equipment mobility: 1 Portable : Hand-held 1 Floorstanding E Fixed 3 Built in 1 Benchmounted C Other (spe

32、cify): Connection to mains supply: 1 Permanent 1 Detachable z Nondetachable r None 3perating conditions: 1 Continuous c Short-time c Intermittent 3verall size of the equipment (length x width x height): Mass of the equipment (kg): Marked degree of protection to IEC 60529: IP- - kcessories and detach

33、able parts included in the evaluation: 3ptions: IOTE - “(see Form A.X)“ refers to a form appended to the report. 6 BS IEC 61010-3-010:1999 Table 1 - Documents attached to this report Document No. Document description Number of pages 7 - STD-BSI BS IEC bLOLO-3-010-ENGL 1999 E lb24bb9 079bllb0 OIT BS

34、IEC 61010-3-010:1999 8 STDmBSI BS IEC bLOLO-3-OLO-ENGL L999 IB Lb24bb9 079bilbL T5b BS IEC 61010-3-010:1999 9 STD-BSI BS IEC b1OLO-3-OLO-ENGL 1777 = 1b24bb7 077b4b2 772 M BS IEC 61010-3-010:1999 Clause Subclause 5 5.1.1 i.l.2 i.l.3 F Requirement I Result I Comments General Required equipment marking

35、s are: a) visible: or or or - from the exterior - after removing a cover - opening a door - after removal from a rack or panel b) not put on parts which can be removed c) Letter symbols (IEC 60027) used d) Graphic symbols (IEC 61 O1 0-1 : table 1) used by an OPERATOR Identification Equipment is iden

36、tified by: - manufacturers name or registered trademark - model number, name or other means - the degree of protection, if any, according to IEC 60529 Mains supply Equipment is marked as follows: a) nature of supply: - a.c. RATED mains frequency or range of frequencies - d.c. with symbol 1 ) RATED s

37、upply voltage) or range :) - maximum RATED power (W or VA) or input current If more than one voltage range: - separate values marked - values differ by less than 20 % (see Form A.3) )r Result: P = Pass F = Fail NA = Not Applicable 10 - STD*BSI BS IEC bLOL0-3-010-ENGL 1777 E Lb24bb7 079b4b3 829 BS IE

38、C 61010-3-010:1999 Clause Subclruw F i.l.4 il .5 Requirement I Result I Comments - indicates the equipment set voltage - PORTABLE EQUIPMENT indication iS visible from the exterior - changing the setting changes the indication e) Accessoty mains socket-outlets accepting standard mains plugs are marke

39、d: - with the voltage if it is different from I the mains supply voltage - for use only with specific equipment If not marked for specific equipment it is marked with: - the maximum RATED current or power, and maximum permitted leakage current - symbol 14 with full details in the documentation or Th

40、e measured value not more than 1 1 O YO (see Form A.3) Fuses OPERATOR replaceable fuse marking (see also 5.4.5) Measuring circuit TERMINALS RATED maximum working voltage or current marked Unless clear indication that below limits: - maximum RATED voltage to earth is marked or - for specific connecti

41、on only, and means for identifying provided - is adjacent to TERMINALS or - if insufficient space: - on the RATING plate or scale plate or - if the TERMINAL is marked with symbol 14 Result: P = Pass F L Fail NA = Not Applicable I I 11 STD*BSI BS IEC bLOLO-3-OLO-ENGL 2777 Lb24bb9 D77bllb4 7b5 E BS IE

42、C 61010-3-010:1999 Clause Subclause 5.1.6 5.1.7 5.1.8 Requirement I Result I Comments TERMINALS permanently connected and not ACCESSIBLE TERMINALS and operating devices Where necessary for safety, indication of purpose of TERMINALS, connectors, controls and I I indicators Mains Supply TERMINALS iden

43、tified Power supply switch on or off position marked if used as disconnecting device TERMINAL marking: a) FUNCTIONAL EARTH TERMINALS b) PROTECTIVE CONDUCTOR TERMINALS - symbol 6 is placed close to or on I I the TERMINAL or - part of appliance inlet c) TERMINALS of measuring and control I I circuits

44、d) TERMINALS supplied from the interOr e) ACCESSIBLE NNCTIONAL EARTH TERMINALS II 9 For ovens and similar equipment an “ON“ indication on each side of the eaubment which has a door in it Equipment protected by DOUBLE INSULAlN or REINFORCED INSULATION Protected throughout (symbol 11 used) Only partia

45、lly protected (symbol 11 not used) Battery charging Equipment with means to charge rechargeable batteries is marked: - to warn against the charging of I I - to indicate the type of rechargeable I I non-rechargeable batteries battery used Result: P = Pass F = Fail NA = Not Applicable 12 BS IEC 61010-

46、3-010:1999 .2 .2.1 o1 i.3 i.4 i.4.1 F Requirement 1 Result I Comments Narning markings - visible when ready for NORMAL USE - if necessary marked with symbol 14 - are near or on applicable parts - statement to isolate or disconnect - advice how to avoid contact with I I ACCESSIBLE HAZARMXIS LIVE part

47、s TERMINAL vdtage mng 1 kV (symbd 12) - - easily touched high temperature parts I I (symbol 13) - Equipment with high ACCESSIBLE current - marking against non-permanent connection - marking location - repeated in installation instructions Durability of markings The required markings remain clear and

48、 legible I I in NORMAL USE (See FOmi A.4) Documentation General Equipment is accompanied by docurnentation which includes: - technical specification - instructions for use I I - name and address of manufacturer or supplier Definition Of INSTALLATION CATEGORY Warning statements and a clear explanatio

49、n of warning symbols: - provided in the documentation or - information is marked on the equipment Result: P = Pass F = Fail NA = Not Applicable 13 STD-BSI BS IEC bLOLO-3-010-ENGL 1777 R lb24bb7 077brlbb 538 I BS IEC 61010-3-010:1999 Requirement Result Clause Subclause 5.4.2 5.4.3 Comments Docurnentation includes: - supply voltage or voltage range - frequency or frequency range - power or current RATING - a description of all input and output connections - RATING of insulation of external circuits, when s