BS IEC 60874-14-5-1998 Connectors for optical fibres and cables - Detail specification for fibre optic connector type SC-PC untuned terminated to single-mode fibre type B1《光纤和光缆连接器.pdf

《BS IEC 60874-14-5-1998 Connectors for optical fibres and cables - Detail specification for fibre optic connector type SC-PC untuned terminated to single-mode fibre type B1《光纤和光缆连接器.pdf》由会员分享，可在线阅读，更多相关《BS IEC 60874-14-5-1998 Connectors for optical fibres and cables - Detail specification for fibre optic connector type SC-PC untuned terminated to single-mode fibre type B1《光纤和光缆连接器.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS IEC 60874-14-5: 1997 Connectors for optical fibres and cables Part 14-5: Detail specification for fibre optic connector type SC-PC untuned terminated to single-mode fibre type B1 ICS 33.180.20BSIEC 60874-14-5:1997 This British Standard, having been prepared under the directionof

2、the Electrotechnical Sector Committee, was publishedunder the authorityofthe Standards Committee and comes into effect on 15 December 1998 BSI 05-1999 ISBN 0 580 30916 9 National foreword This British Standard reproduces verbatim IEC60874-14-5:1997 and implements it as the UK national standard. The

3、UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Interconnecting devices and passive components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee

4、any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From1 January

5、1997, all IEC publications have the number60000 added to the old number. For instance, IEC27-1 has been renumbered as IEC60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references The British S

6、tandards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Sta

7、ndard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover

8、, an inside front cover, pages i and ii, theIEC title page, page ii, pages1to15 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication

9、 Amd. No. Date CommentsBSIEC 60874-14-5:1997 BSI 05-1999 i Contents Page National foreword Inside front cover Figure 1 Plug mating face dimensions 2 Figure 2a Ferrule endface geometry after termination 4 Figure 2b Allowable undercut BK versus radius rBF 5 Figure 3 Plug dimension 5 Figure 4 Example o

10、f component marking 6 Table 1 Fixed sample test schedule for qualification approval 7 Table 2 Lot-by-lot quality conformance inspection schedule 8 Table 3 Periodic quality conformance inspection schedule 9 Table 4 Details, measurements and performance requirements 10ii blankii blankBSIEC 60874-14-5:

11、1997 BSI 05-1999 1 CONNECTORS FOR OPTICAL FIBRES AND CABLES Part 14-5: Detail specification for fibre optic connector type SC-PC untuned terminated to single-mode fibre type B1 NATIONAL STANDARDS ORGANIZATION: . Date: . DETAIL SPECIFICATION IEC QC910004XX0005. FIBRE OPTIC COMPONENT OF ASSESSED QUALI

12、TY IN ACCORDANCE WITH GENERIC SPECIFICATION: QC910000 (IEC60874-1) BLANK DETAIL SPECIFICATION: QC 910001 (IEC 60874-1-1) CONNECTOR SET FOR OPTICAL FIBRES AND CABLES CLASSIFICATION: Type: Name: SC For use in datacom applications as specified in ISO/IEC International Standard 11801: “Generic cabling f

13、or customer premises” Configuration: plug-adaptor-plug Coupling: push-pull Control dimensions: Plug: see Figure 1, Figure 2 and Figure 3 Adaptor: see IEC60874-14-3 Arrangement: patchcord arrangement Style: Fibre retention: as required Cable retention: as required Optical coupling: butting Alignment:

14、 resilient sleeve alignment Variants: see page 6 Climatic category: 10/60/4 Environmental category: 4 Assessment level: A QUALIFICATION PROCEDURE: Fixed sample procedure SAFETY WARNING: Take care when handling small diameter optical fibre to prevent puncturing the skin, especially in the eye area. D

15、irect viewing of the end of an optical fibre when it is propagating energy is not recommended unless prior assurance is obtained as to the safe energy output level. Applicable fibre cable information Mode field diameter In accordance with IEC60793-2 Cladding diameter In accordance with IEC60793-2 Co

16、re/cladding concentricity error In accordance with IEC60793-2 Buffer diameter 250 15, 500 30, 900 504m Jacket outer diameter As required per variant Fibre cut-off wavelength 11001280nm Additional information Attenuation in random connection: less than 0,80 dB (95 % probability) less than 0,40 dB (av

17、erage)BSIEC 60874-14-5:1997 2 BSI 05-1999 Figure 1 Plug mating face dimensionsBSIEC 60874-14-5:1997 BSI 05-1999 3 Reference Dimensions Notes Minimum Maximum A B C D E F G H I J K L M N O P Q R rS T U V cBC 2,4985mm 4,8mm 6,8mm 4,9mm 6,7mm 19 25 7,15mm 0,8mm 5,3mm 0,1mm 2,11mm 2,0mm 6,6mm 1,6mm 8,89m

18、m 0,8mm 7,29mm 0,8mm 4,05mm 5,4mm 0mm 0mm 2,4995mm 4,9mm 7,4mm 5,3mm 6,8mm 23 35 7,50mm 1,2mm 5,5mm 0,05mm 2,5mm 2,8mm 6,8mm 1,8mm 8,99mm 1,0mm 7,39mm 0,9mm 4,15mm 5,6mm 0,5mm 0,5mm 1, 2 3 Radius Chamfer NOTE 1Ferrule compression force shall be from7,8N to11,8N, when the ferrule is compressed to a p

19、oint where H is7 0,1mm. NOTE 2This value shows the dimension after the ferrule is polished and in the unmated condition. NOTE 3The negative dimension indicates that the position of the inside bottom plane is left-direction relative to the mechanical reference plane. NOTE 4Where a tolerance of form i

20、s not specified, the limits of the dimensions for a feature control the form as well as the size. NOTE 5Where interrelated features of size (features shown with a common axis or centre plane) have no geometric tolerance of location or run out specified, the limits of the dimensions for a feature con

21、trol the location tolerance as well as the size. NOTE 6Where perpendicular features (features shown at right angles) have no geometric tolerance of orientation or run out specified, the limits of the dimensions for a feature control the orientation tolerance as well as the size.Figure 1 Plug mating

22、face dimensions (continued)BSIEC 60874-14-5:1997 4 BSI 05-1999 Reference Dimensions Notes Minimum Maximum rBF BK BG BG BI 10mm 0,0001mm 1,76mm 1,90mm 25 25mm see graph 2,26mm 2,26mm 35 1, radius 2 diameter, 4 diameter, 5 NOTE 1Eccentricity of a spherical polished ferrule endface is less than50 4m. N

23、OTE 2The negative dimension refers to the fibre protrusion. NOTE 3Break edge. NOTE 4This value is applicable to the variant numbers1 001, 1 003, 1 005and1 007. NOTE 5This value is applicable to the variant numbers 1 002, 1 004, 1 006 and 1 008. Figure 2a Ferrule endface geometry after terminationBSI

24、EC 60874-14-5:1997 BSI 05-1999 5 Figure 2b Allowable undercut BK versus radius rBF Reference Dimensions mm Minimum Maximum Notes BD BE BE BE BE 2,2 2,6 2,9 3,2 60 1 2 3 4 NOTE 1This value is applicable to the variants number 1001 and 1002. NOTE 2This value is applicable to the variants number 1003 a

25、nd 1004. NOTE 3This value is applicable to the variants number 1005 and 1006. NOTE 4This value is applicable to the variants number 1007 and 1008. Figure 3 Plug dimensionBSIEC 60874-14-5:1997 6 BSI 05-1999 VARIANT IDENTIFICATION NUMBERS Number: QC910X01/0005-ZZZZ ZZZZ Component name Variant feature

26、Applicable cable jacket diameter Ferrule material Dimension BG 1001 Plug 2,0mm Zirconia 1,76 2,26 1 002 Plug 2,0mm Zirconia 1 90 2,26 1 003 Plug 2,4mm Zirconia 1,76 2,26 1 004 Plug 2,4mm Zirconia 1,90 2,26 1 005 Plug 2,7mm Zirconia 1,76 2,26 1 006 Plug 2,7mm Zirconia 1,90 2,26 1 007 Plug 3,0mm Zirco

27、nia 1,76 2,26 1 008 Plug 3,0mm Zirconia 1,90 2,26 SUPPLEMENTARY INFORMATION Preferred colour: Colour of the coupling sleeve and boot shall be blue according to: RAL5015. Component marking: The name and/or manufacturers identification mark may be permanently identified. Figure 4 shows an example of t

28、he location of the component marking. Figure 4 Example of component markingBSIEC 60874-14-5:1997 BSI 05-1999 7 Table 1 Fixed sample test schedule for qualification approval Test sequence Reference IEC 60874-1 (IEC61300) n Group 0 20 Visual examination Dimensions Ferrule compression force 4.4.1 4.4.2

29、 4.4.12 (3-1) (3-1) (3-22) Group 1 Attenuation Return loss 4.4.7 4.4.12 (3-4) (3-6) 20 Group 2 6 Cold Dry heat Damp heat (steady state) 4.5.17 4.5.18 4.5.19 (2-17) (2-18) (2-19) Group 3 6 Drop Engagement and separation force Mechanical endurance 4.5.14 4.4.5 4.5.32 (2-12) (3-11) (2-2) Group 4 Vibrat

30、ion Change of temperature (test Nb) 4.5.1 4.5.22 (2-1) (2-22) 4 Group 5 4 Strength of coupling mechanism Cable pulling Cable torsion 4.5.6 4.5.4 4.5.5 (2-6) (2-4) (2-5) Group 6 NA Fibre or ferrule retention 4.5.2 (2-4) NOTE 1n = sample size (number of plugs). NOTE 2To satisfy the qualification appro

31、val requirements of the detail specification there shall be no failures of any in the sample groups for any test parameter. If a failure does occur this shall be investigated and the cause of failure identified and corrected. The test which is affected shall then be repeated using the minimum sample

32、 size stated in this detail specification. A fully documented test report and supporting data shall be prepared and shall be available for inspection. Failures and the corrective action taken to eliminate failures shall be documented and evidence shall be presented to show that the corrective action

33、 will have no detrimental effect on the performance in any of the other tests. Design changes, as opposed to improvements in quality control, will usually be deemed to necessitate a repeat of the full qualification programme. NOTE 3Unless otherwise indicated, the test details, measurements and perfo

34、rmance requirements are given in Table 4. NOTE 4Only group 1 tests shall be carried out using a reference connector. All other tests shall be carried out using the samples from the relevant group at random.BSIEC 60874-14-5:1997 8 BSI 05-1999 Table 2 Lot-by-lot quality conformance inspection schedule

35、 Groups A and B Test sequence Reference IEC60874-1 (IEC 61300) Assessment level A IL AQL Group A Visual examination 4.4.1 (3-1) II 4% Radius Undercut/Protrusion Eccentricity of spherical polished endface 4.4.2 (3-1) (3-23) (3-25) Group B Attenuation Return loss 4.4.7 4.4.12 (3-4) (3-6) II 4% NOTE 1U

36、nless otherwise indicated, the details, measurements and performance requirements are given in Table 4. NOTE 2IL = Inspection level; AQL = Acceptable quality level. NOTE 3Only group B tests shall be carried out using a reference connector. All other tests shall be carried out using the samples from

37、the relevant group at random.BSIEC 60874-14-5:1997 BSI 05-1999 9 Table 3 Periodic quality conformance inspection schedule Groups C and D Test sequence Reference IEC 60874-1 (IEC61300) Assessment level A n p Group C0 18 24 Visual examination Dimensions Ferrule compression force 4.4.1 4.4.2 4.4.12 (3-

38、1) (3-1) (3-22) Group C1 Attenuation Return loss 4.4.7 4.4.12 (3-4) (3-6) 18 24 Group C2 6 24 Cold Dry heat Damp heat (steady state) 4.5.17 4.5.18 4.5.19 (2-17) (2-18) (2-19) Group D0 Visual examination Dimensions Ferrule compression force 4.4.1 4.4.2 4.4.12 (3-1) (3-1) (3-22) 20 48 Group D1 20 48 A

39、ttenuation Return loss 4.4.7 4.4.12 (3-4) (3-6) Group D2 6 48 Cold Dry heat Damp heat (steady state) 4.5.17 4.5.18 4.5.19 (2-17) (2-18) (2-19) Group D3 Drop Engagement and separation force Mechanical endurance 4.5.14 4.4.5 4.5.2 (2-12) (3-11) (2-2) 6 48 Group D4 Vibration Change of temperature (test

40、 Nb) 4.5.1 4.5.22 (2-1) (2-22) 4 48 Group D5 Strength of coupling mechanism Cable pulling Cable torsion 4.5.6 4.5.4 4.5.5 (2-6) (2-4) (2-5) 4 48 Group D6 NA NA Fibre or ferrule retention 4.5.2 (2-4) NOTE 1Unless otherwise indicated, the details, measurements and performance requirements are given in

41、 Table 4. NOTE 2To satisfy the qualification approval requirements of the detail specification there shall be no failures of any in the sample groups for any test parameter. If a failure does occur this shall be investigated and the cause of failure identified and corrected. The test which is affect

42、ed shall then be repeated using the minimum sample size stated in this detail specification. A fully documented test report and supporting data shall be prepared and shall be available for inspection. Failures and the corrective action taken to eliminate failures shall be documented and evidence sha

43、ll be presented to show that the corrective action will have no detrimental effect on the performance in any of the other tests. Design changes, as opposed to improvements in quality control, will usually be deemed to necessitate a repeat of the full qualification programme. NOTE 3n = sample size (n

44、umber of plugs); p = periodicity in months. NOTE 4Only group C1 and D1 tests shall be carried out using a reference connector. All other tests shall be carried out using the samples from the relevant group at random.BSIEC 60874-14-5:1997 10 BSI 05-1999 Table 4 Details, measurements and performance r

45、equirements Visual examination 4.4.1 (61300-3-1) Requirements: Marking shall be clear Coupling sleeve shall be movable smoothly Dimensions 4.4.2 (61300-3-1) Requirements: All size dimensions shall be in accordance with this specification Attenuation 4.4.7 (61300-3-4) Details: Method No. 7 Definition

46、s of reference plug are as follows: Ferrule outer diameter is 2,499 0,0003 mm Concentricity of the fibre core with the outer diameter of the ferrule is less than 0,64m Eccentricity of a spherical polished ferrule endface is less than 304m Adaptor shall be in accordance with IEC 60874-14-3 Number of

47、measurements to be averaged: 5 Source: LD. Peak wavelength: 1,34m Preconditioning procedure: clean ferrule endface and alignment sleeve using lint free material Recovery procedure: none Requirements: Allowable attenuation: less than0,5dB against reference plug using reference adaptor Return loss 4.4

48、.12 (61300-3-6) Details: Method 3 Source: LD Peak wavelength: 1,34m Adaptor shall be in accordance with IEC60874-14-3 Preconditioning procedure: clean ferrule endface and alignment sleeve using lint free material Recovery procedure: none Requirements: Allowable return loss: more than26dBBSIEC 60874-

49、14-5:1997 BSI 05-1999 11Table 4 Details, measurements and performance requirements Cold 4.5.17 (61300-2-17) Details: Temperature: 10 C Duration: 96h Specimen optically functioning Conditioning procedure: specimen lowered to test temperature and returned to room temperature at a rate not to exceed 1 /min Deviation