BS G 207-1969 Specification for aircraft electrical circuit diagrams《航空用电路图规范》.pdf
《BS G 207-1969 Specification for aircraft electrical circuit diagrams《航空用电路图规范》.pdf》由会员分享,可在线阅读,更多相关《BS G 207-1969 Specification for aircraft electrical circuit diagrams《航空用电路图规范》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS G207:1969 Specification for Aircraft electrical circuit diagrams UDC 629.7:621.316.31.061:744.423BSG207:1969 This BritishStandard, having been approved by the AerospaceIndustry StandardsCommittee, waspublished underthe authorityofthe Executive Boardof the Institu
2、tionon 30January1969 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/41 Draft for comment66/14186 ISBN 580 00446 5 Foreword This BritishStandard has been prepared on the basis of the standard procedure for electrical diagrams for aircraft formula
3、ted by the Society of British Aerospace Companies. The standard makes reference to the following: BS3238, Graphical symbols for components of servo-mechanisms. BS3939, Graphical symbols for electrical power, telecommunications and electronics diagrams. NOTEWhere metric equivalents are shown in paren
4、theses after values in imperial units, the figures in imperial units are to be regarded as the standard. The metric equivalents are approximate; more accurate conversions should be based on the tables in BS350, “Conversion factors and tables”. A British Standard does not purport to include all the n
5、ecessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, page
6、s1 to3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSG207:1969 BSI 12-1999 i Contents Page Foreword I
7、nside front cover 1 Scope 1 2 Symbols 1 3 Presentation 1 4 Layout 1 5 Circuit condition 1 6 Titles 1 7 Terminal identification 1 8 Notes 2 9 Cable runs 2 10 Identification 2 11 Cross references 2 12 Colour coding 2 Appendix A Example of circuit diagram 3ii blankBSG207:1969 BSI 12-1999 1 1 Scope This
8、 BritishStandard provides for uniformity in the preparation of aircraft diagrams to allow the greatest ease of drawing consistent with the need for clear definition and legibility. It is intended that these drawings should be of a format suitable for use as production drawings or for reproduction in
9、 wiring diagram manuals. A diagram illustrating the application of the principles laid down in the standard is shown in Appendix A. 2 Symbols Symbols used in the preparation of aircraft electrical circuit diagrams shall be selected from those shown in BS3939, “Graphical symbols for electrical power,
10、 telecommunications and electronics diagrams” 1) , and BS3238 “Graphical symbols for components of servo-mechanisms”. 3 Presentation 3.1 Electrical diagrams shall be drawn to a size suitable for reproduction on11 in by16 in(280mm by405mm) sheets with the following margin limitations: The sheets may
11、be folded once to11 in by8“ in(280mm by215mm). It may be necessary to present the drawing on more than one sheet; in this connection attention is drawn to Clause11. NOTEAll dimensions quoted in this BritishStandard relate to11 in by16 in sheet sizes and should be proportionately increased in larger
12、sheets. 3.2 If a complex component appears more than once on a diagram it is only necessary to draw the symbol once. Repetitions of the component may be in the form of a box with the appropriately annotated connections only. 3.3 All symbols shall be drawn to a size compatible with legibility upon re
13、production. Component outlines where required shall be represented by the appropriate chain-dotted line. 3.4 Lines shall be sharp and dense to obtain good reproduction. As most diagrams will be altered in size on reproduction no exact thickness of line is specified. 4 Layout In general, electrical w
14、iring diagrams shall be laid out with the power supplies either at the left or top of the drawing. 5 Circuit condition 5.1 Circuits shall be drawn in the “aircraft-on-the-ground” condition with the main power off. In general, all switches shall be off and allrelays, solenoids and contactors shown in
15、 their de-energized state. Circuit-breakers shall be drawn in their closed condition. 5.2 Should it be necessary to deviate from this form of presentation a note shall be added to define clearly the state of the aircraft as applied to the particular diagram. For example, for automatic pilot cut-out
16、switches, such a note might read: Aircraft system in take-off state; Main power on; Flaps down, elevator gear change “in coarse”. 6 Titles 6.1 Captions for technical publication shall be along the bottom right-hand corner of the diagrams in letters which, when the drawing is reproduced to11in 16in(2
17、80mm 405mm) size, are0.125in(3.2mm) size. 6.2 All subtitles shall be situated centrally at the top of the appropriate group and every effort made to use a standard nomenclature; the word “EQUIPMENT” shall not be used as a group heading. An approximate location of all components shall be indicated. 6
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSG2071969SPECIFICATIONFORAIRCRAFTELECTRICALCIRCUITDIAGRAMS 航空 用电 规范 PDF

链接地址:http://www.mydoc123.com/p-582822.html