BS EN ISO 8503-1-2012 Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates Specifico.pdf

《BS EN ISO 8503-1-2012 Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates Specifico.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 8503-1-2012 Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates Specifico.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 8503-1:2012Preparation of steel substratesbefore application of paintsand related products Surfaceroughness characteristics ofblast-cleaned steel substratesPart 1: Spec

2、ifications and definitions forISO surface profile comparators for theassessment of abrasive blast-cleanedsurfacesBS EN ISO 8503-1:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of . It supersedes BSEN ISO 8503-1:1995 which is withdrawn.The UK participation in it

3、s preparation was entrusted to TechnicalCommittee STI/21, Surface preparation of steel.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for it

4、s correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 63468 0ICS 17.040.20; 25.220.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Po

5、licy and Strategy Committee on 31 March 2012.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8503-1 February 2012 ICS 25.220.10 Supersedes EN ISO 8503-1:1995English Version Preparation of steel substrates before application of paints and

6、related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:2012) Prparation des subjectiles dacier avant application de peintures

7、 et de produits assimils - Caractristiques de rugosit des subjectiles dacier dcaps - Partie 1: Spcifications et dfinitions des comparateurs viso-tactiles ISO pour caractriser les surfaces dcapes par projection dabrasif (ISO 8503-1:2012) Vorbereitung von Stahloberflchen vor dem Auftragen von Beschich

8、tungsstoffen - Rauheitskenngren von gestrahlten Stahloberflchen - Teil 1: Anforderungen und Begriffe fr ISO-Rauheitsvergleichsmuster zur Beurteilung gestrahlter Oberflchen (ISO 8503-1:2012) This European Standard was approved by CEN on 14 February 2012. CEN members are bound to comply with the CEN/C

9、ENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centr

10、e or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the

11、official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,

12、 Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reser

13、ved worldwide for CEN national Members. Ref. No. EN ISO 8503-1:2012: EBS EN ISO 8503-1:2012EN ISO 8503-1:2012 (E) 3 Foreword This document (EN ISO 8503-1:2012) has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes” in collaboration with Technical Committee CEN/TC 139 “Paints and v

14、arnishes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2012, and conflicting national standards shall be withdrawn at the latest by August 2012.

15、Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 8503-1:1995. According to the CEN/CENELEC Internal Reg

16、ulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M

17、alta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 8503-1:2012 has been approved by CEN as a EN ISO 8503-1:2012 without any modification. BS EN ISO 8503-1:2012ISO 8503-1:2012(E) ISO 2

18、012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope 12 Normative references . 13 Terms and definitions . 14 ISO surface profile comparators . 35 Ranges of the profile gradings 46 Calibration of ISO comparators . 57 Maintenance and re-calibration of ISO surface profile comparator

19、s 58 Calibration certificate for ISO surface profile comparators . 5Annex A (normative) Care of ISO surface profile comparators . 7Bibliography . 8BS EN ISO 8503-1:2012ISO 8503-1:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards b

20、odies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizati

21、ons, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the

22、ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the

23、 member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 8503-1 was prepared by Technical Committee ISO/TC 35, Paints and var

24、nishes, Subcommittee SC 12, Preparation of steel substrates before application of paints and related products.This second edition cancels and replaces the first edition (ISO 8503-1:1988), which has been technically revised.ISO 8503 consists of the following parts, under the general title Preparation

25、 of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates: Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces Part 2: Method for the grading

26、of surface profile of abrasive blast-cleaned steel Comparator procedure Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile Focusing microscope procedure Part 4: Method for the calibration of ISO surface profile comparators and for the d

27、etermination of surface profile Stylus instrument procedure Part 5: Replica tape method for the determination of the surface profileiv ISO 2012 All rights reservedBS EN ISO 8503-1:2012ISO 8503-1:2012(E)IntroductionThe performance of protective coatings of paint and related products applied to steel

28、is significantly affected by the state of the steel surface immediately prior to painting. The principal factors that are known to influence this performance are:a) the presence of rust and mill scale;b) the presence of surface contaminants, including salts, dust, oils and greases;c) the surface pro

29、file.International Standards ISO 8501 (all parts), ISO 8502 (all parts) and ISO 8503 (all parts) have been prepared to provide methods of assessing these factors, while ISO 8504 (all parts) provides guidance on the preparation methods which are available for cleaning steel substrates, indicating the

30、 capabilities of each in attaining specified levels of cleanliness.These International Standards do not contain provisions for the protective coating systems to be applied to the steel surface or for the surface quality provisions for specific situations, even though surface quality can have a direc

31、t influence on the choice of protective coating to be applied and on its performance. Such provisions are found in other documents, such as national standards and codes of practice. It is necessary for the users of these International Standards to ensure that the qualities specified are: compatible

32、and appropriate both for the environmental conditions to which the steel is exposed and for the protective coating system to be used; within the capability of the cleaning procedure specified.The four International Standards referred to above deal with the following aspects of preparation of steel s

33、ubstrates: ISO 8501: Visual assessment of surface cleanliness; ISO 8502: Tests for the assessment of surface cleanliness; ISO 8503: Surface roughness characteristics of blast-cleaned steel substrates; ISO 8504: Surface preparation methods.Irrespective of the procedures and the type of abrasive used

34、for the preparation of steel substrates, the surface after blast-cleaning consists of random irregularities with peaks and valleys that are not easily characterized. Consequently, it was concluded that, because of this random nature, no method is capable of giving a precise value for the profile. Th

35、us, it is intended that the profile be identified as either dimpled (where shot abrasives are used) or angular (where grit abrasives are used) and that it be graded as “fine”, “medium” or “coarse”, each grade being defined by the limits specified in this part of ISO 8503. These surface characteristi

36、cs are considered to give sufficient distinguishing features for most painting requirements.Particular attention, however, is drawn to the fact that the grades “fine”, “medium” and “coarse” represent different ranges in terms of roughness parameters, dependent upon whether these grades are applied t

37、o shot abrasive or grit abrasive blast-cleaned surfaces. In consequence, the effect produced on a given coating by a given grade “fine”, “medium” or “coarse” is determined not only by the specific surface character but also by the specific roughness value Ry5or hybelonging to that grade. Where surfa

38、ce profile is particularly important, both the grade of the surface profile (“fine”, “medium” or “coarse”) and the type of abrasive which is to be used are to be specified.This part of ISO 8503 specifies the limits for the “fine”, “medium” and “coarse” surface for both dimpled and angular profiles,

39、and specifies the design of ISO comparators for reference purposes.Requirements regarding the care of ISO surface profile comparators are given in Annex A.ISO 8503-2 describes the method of using these ISO comparators. The many abrasive blast-cleaning procedures in common use are described in ISO 85

40、04-2. ISO 2012 All rights reserved vBS EN ISO 8503-1:2012BS EN ISO 8503-1:2012Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates Part 1: Specifications and definitions for ISO surface profile comparato

41、rs for the assessment of abrasive blast-cleaned surfaces1 ScopeThis part of ISO 8503 specifies the requirements for ISO surface profile comparators, which are intended for visual and tactile comparison of steel substrates which have been blast-cleaned with either shot abrasives or grit abrasives. Th

42、is part of ISO 8503 also includes definitions of the terms used in the ISO 8503 series and requirements for the care of ISO surface profile comparators.NOTE 1 ISO surface profile comparators are used for assessing, on site, the roughness of surfaces before the application of paints and related produ

43、cts or other protective treatments.NOTE 2 Where appropriate, these ISO comparators can be used for assessing the roughness profile of other abrasive blast-cleaned substrates and, in addition, their use is not restricted solely to surfaces that are to be painted.2 Normative referencesThe following re

44、ferenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 8501-1, Preparation of steel substrates before application of

45、paints and related products Visual assessment of surface cleanliness Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatingsISO 8503-2, Preparation of steel substrates before application of paints and related products

46、 Surface roughness characteristics of blast-cleaned steel substrates Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel Comparator procedureISO 8503-3, Preparation of steel substrates before application of paints and related products Surface roughness characteristics o

47、f blast-cleaned steel substrates Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile Focusing microscope procedureISO 8503-4, Preparation of steel substrates before application of paints and related products Surface roughness characteris

48、tics of blast-cleaned steel substrates Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile Stylus instrument procedure3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.INTERNATIONAL STAND

49、ARD ISO 8503-1:2012(E) ISO 2012 All rights reserved 1BS EN ISO 8503-1:2012ISO 8503-1:2012(E)3.1surface profilemicro-roughness of a surfaceNOTE This is generally expressed as the height of the major peaks relative to the major valleys. This term is defined in ISO 4287 as a “profile that results from the intersection of the real surface by a specified plane”. Characteristics of the roughness of blast-cleaned surfaces are defined in 3.7, 3.8, 3.10 to 3.12 and in ISO 8503-4.3.2ISO surface profile comparator