BS EN ISO 8495-2013 Metallic materials Tube Ring-expanding test《金属材料 管材 环形扩口试验》.pdf

《BS EN ISO 8495-2013 Metallic materials Tube Ring-expanding test《金属材料 管材 环形扩口试验》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 8495-2013 Metallic materials Tube Ring-expanding test《金属材料 管材 环形扩口试验》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 8495:2013Metallic materials Tube Ring-expanding testBS EN ISO 8495:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 8495:2013.It supersedes BS EN ISO 8495:2004 which is withdrawn.The UK participation in its preparation

2、was entrusted to TechnicalCommittee ISE/101/2, Ductility testing.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication.

3、The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 82940 6ICS 77.040.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30

4、 November 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8495 November 2013 ICS 77.040.10 Supersedes EN ISO 8495:2004English Version Metallic materials - Tube - Ring-expanding test (ISO 8495:2013) Matriaux mtalliques - Tubes - Essai

5、 de dilatation danneaux (ISO 8495:2013) Metallische Werkstoffe - Rohr - Ringaufdornversuch (ISO 8495:2013) This European Standard was approved by CEN on 28 October 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

6、Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (En

7、glish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium

8、, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerla

9、nd, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Me

10、mbers. Ref. No. EN ISO 8495:2013 EBS EN ISO 8495:2013EN ISO 8495:2013 (E) 3 Foreword This document (EN ISO 8495:2013) has been prepared by Technical Committee ISO/TC 164 “Mechanical testing of metals“ in collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” t

11、he secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the latest by May 2014. Attention is draw

12、n to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 8495:2004. According to the CEN-CENELEC Internal Regulations, the natio

13、nal standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lith

14、uania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 8495:2013 has been approved by CEN as EN ISO 8495:2013 without any modification. BS EN ISO 8495:2013ISO 8495:201

15、3(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Symbols, designations and units 13 Principle 14 Apparatus . 25 Test piece 26 Procedure. 27 Test report . 3BS EN ISO 8495:2013ISO 8495:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide feder

16、ation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that commit

17、tee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and

18、those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part

19、2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the docume

20、nt will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 164, Mechanica

21、l testing of metals, Subcommittee SC 2, Ductility testing.This third edition cancels and replaces the second edition (ISO 8495:1998), of which it constitutes a minor revision.iv ISO 2013 All rights reservedBS EN ISO 8495:2013INTERNATIONAL STANDARD ISO 8495:2013(E)Metallic materials Tube Ring-expandi

22、ng test1 ScopeThis International Standard specifies a method for a ring-expanding test on tubes, that is used to reveal defects both on the surfaces and within the tube wall by expanding the test piece using a conical mandrel until fracture occurs. It may be also used to assess the ability of tubes

23、to undergo plastic deformation.The ring-expanding test is applicable to tubes having an outside diameter from 18 mm up to and including 150 mm and a wall thickness from 2 mm up to and including 16 mm.2 Symbols, designations and unitsSymbols, designations and units for the ring-expanding test are giv

24、en in Table 1 and are shown in Figure 1.Table 1Symbol Designation Unita aDDmmax.Dmmin.DukLWall thickness of the tubeOriginal outside diameter of the tubeMaximum diameter of the conical mandrelMinimum diameter of the conical mandrelMaximum outside diameter of the expanded part of the test pieceLength

25、 of the taper of the conical mandrelLength of the test piece before the testmmmmmmmmmmmmmmaThe symbol T is also used in steel tube standards.3 PrincipleExpanding a ring cut from the end of a tube, over a conical mandrel until fracture, or until the expansion of the test piece reaches a value specifi

26、ed in the relevant product standard (see Figure 1). ISO 2013 All rights reserved 1BS EN ISO 8495:2013ISO 8495:2013(E)Figure 14 Apparatus4.1 Variable-speed press or universal testing machine.4.2 Conical mandrel, having a working length preferably tapered 1:5 as shown in Figure 1, unless otherwise spe

27、cified in the relevant product standard, and its surface shall be of sufficient hardness, well-polished and free from scores.5 Test piece5.1 The length of the test piece shall be between 10 mm and 16 mm. Test pieces shall be taken from the ends of deburred tubes as manufactured before they are cut t

28、o length. The rings shall be cut so that the planes of the end faces are parallel with each other and perpendicular to the axis of the tube.5.2 The edges of the test piece may be rounded by filing or chamfered by other methods.NOTE Non-rounded or non-chamfered edges are permissible, if the test resu

29、lt meets the test requirements.5.3 When welded tubes are subjected to the test, the internal weld flash may be removed.6 Procedure6.1 In general, the test shall be carried out at ambient temperature within the limits of 10 C to 35 C. The test carried out under controlled conditions shall be made at

30、a temperature of 23 C 5 C.2 ISO 2013 All rights reservedBS EN ISO 8495:2013ISO 8495:2013(E)6.2 Before testing, the rings and the conical mandrel may be lubricated. Rings of the same size and the same type of metal may be placed one on top of each other. The rings and the conical mandrel shall be con

31、centric (see Figure 1).6.3 Force the conical mandrel into the rings until the required expansion is reached or the rings fracture.6.4 The rate of penetration of the conical mandrel shall not exceed 30 mm/s.6.5 The relative expansion shall be calculated in accordance with the relevant product standar

32、d.6.6 Interpretation of the ring-expanding test shall be carried out in accordance with the requirements of the relevant product standard. When these requirements are not specified, the test piece shall be considered to have passed the test if no cracks are visible without the use of magnifying aids

33、.7 Test reportA test report shall be provided when so specified in the relevant product standard. In this case, the test report shall include at least the following information:a) a reference to this International Standard, i.e. ISO 8495;b) identification of the test piece;c) dimensions of the test

34、piece; d) relative expansion;e) taper of the conical mandrel if different from that given in 4.2;f) result of the test. ISO 2013 All rights reserved 3This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other stand

35、ards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring toget

36、her business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organiz

37、ations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services te

38、am or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards

39、Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant ac

40、cess to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in sin

41、gle copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member an

42、d the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For

43、further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication

44、please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization

45、 bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recordi

46、ng or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW