BS EN ISO 7840-2013 Small craft Fire-resistant fuel hoses《小型船舶 耐火燃油软管》.pdf

《BS EN ISO 7840-2013 Small craft Fire-resistant fuel hoses《小型船舶 耐火燃油软管》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 7840-2013 Small craft Fire-resistant fuel hoses《小型船舶 耐火燃油软管》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 7840:2013Small craft Fire-resistant fuelhoses (ISO 7840:2013)BS EN ISO 7840:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 7840:2013.It supersedes BS EN ISO 7840:2004 which is withdrawn.The UK participation in its pre

2、paration was entrusted to TechnicalCommittee GME/33, Small craft.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication.

3、The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 75488 3ICS 47.080Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 Ju

4、ly 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 7840 July 2013 ICS 47.080 Supersedes EN ISO 7840:2004English Version Small craft - Fire-resistant fuel hoses (ISO 7840:2013) Petits navires - Tuyaux souples pour carburant rsistants

5、au feu (ISO 7840:2013) Kleine Wasserfahrzeuge - Feuerwiderstandsfhige Kraftstoffschluche (ISO 7840:2013) This European Standard was approved by CEN on 8 June 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standa

6、rd the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English,

7、 French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulg

8、aria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tu

9、rkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN

10、 ISO 7840:2013: EBS EN ISO 7840:2013EN ISO 7840:2013 (E) 3 Foreword This document (EN ISO 7840:2013) has been prepared by Technical Committee ISO/TC 188 “Small craft”. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsemen

11、t, at the latest by January 2014, and conflicting national standards shall be withdrawn at the latest by January 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifyin

12、g any or all such patent rights. This document supersedes EN ISO 7840:2004. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive, see

13、 informative Annex ZA, which is an integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, E

14、stonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice T

15、he text of ISO 7840:2013 has been approved by CEN as EN ISO 7840:2013 without any modification. BS EN ISO 7840:2013EN ISO 7840:2013 (E) 4 Annex ZA (informative) Relationship between this Standard and the Essential Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC By agreement

16、between ISO and CEN, this CEN annex is included in the DIS and the FDIS but will not appear in the published ISO standard. This Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Req

17、uirements of the New Approach Directive 94/25 EC as amended by Directive 2003/44/EC. Once this standard is cited in the Official Journal of the European Union under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of t

18、his standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations. Table ZA.1 Correspondence between this Standard and EU Directive 94/25/EC as amended

19、 by Directive 2003/44/EC Clause(s)/sub-clause(s) of this standard Essential Requirements (ERs) of EU Directive 94/25/EC as amended by Directive 2003/44/EC Qualifying remarks/Notes All clauses Annex I A, Clause 5.1.1, Inboard Engine Annex I A, Clause 5.2.1, Fuel system, General Annex I A, Clause 5.6.

20、1, Fire protection, General Annex II, Components, 4 This standard is relevant in respect of fuel filling lines and fuel vent lines installed both inside and outside the engine compartment. It does not apply to hoses installed entirely within the splash well and connected directly to an outboard engi

21、ne. WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard. BS EN ISO 7840:2013ISO 7840:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 General requirements . 14 Nominal bo

22、re 15 Physical tests on finished hose 25.1 General . 25.2 Test liquids 25.3 Bursting pressure . 25.4 Vacuum-collapse test . 35.5 Volume change in test liquids. 35.6 Mass reduction of test hose 35.7 Fire resistance . 35.8 Effect of ozone . 35.9 Fuel permeation . 35.10 Cold-flex test . 45.11 Abrasion

23、test 38 mm and larger fuel-fill hose with helical wire embedded reinforcement 45.12 Dry heat resistance 45.13 Oil resistance test 45.14 Adhesion test 46 Marking 4Annex A (normative) Fire test . 6Annex B (normative) Fuel permeation test (or equivalent test method) 8Bibliography .10BS EN ISO 7840:2013

24、ISO 7840:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subjec

25、t for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC)

26、 on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be not

27、ed. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or

28、 all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and do

29、es not constitute an endorsement. The committee responsible for this document is ISO/TC 188, Small craft.This fourth edition cancels and replaces the third edition (ISO 7840:2004), which has been technically revised, mainly concerning test liquids in 5.2 to cover hoses long-term resistance to petrol

30、 fuel mixed with ethanol as well as diesel fuel mixed with Fatty Acid Methyl Esters (FAME).iv ISO 2013 All rights reservedBS EN ISO 7840:2013INTERNATIONAL STANDARD ISO 7840:2013(E)Small craft Fire-resistant fuel hoses1 ScopeThis International Standard specifies general requirements and physical test

31、s for fire-resistant hoses for conveying petrol or petrol blended with ethanol and diesel fuel or diesel fuel blended with FAME, designed for a working pressure not exceeding 0,34 MPa for hoses with nominal bore up to and including 10 mm and 0,25 MPa for hoses up to 63 mm inner diameter in craft of

32、hull length up to 24 m.It applies to hoses for small craft with permanently installed fuel systems. It does not apply to hoses entirely within the splash well at the stern of the craft connected directly to an outboard engine.Specifications for non-fire-resistant fuel hoses are given in ISO 84691. S

33、pecifications for permanently installed fuel systems are given in ISO 10088.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated ref

34、erences, the latest edition of the referenced document (including any amendments) applies.ISO 3:1973, Preferred numbers Series of preferred numbersISO 1307, Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hosesISO 1402, Rubber and plastics

35、hoses and hose assemblies Hydrostatic testingISO 1817:2011, Rubber, vulcanized or thermoplastic Determination of the effect of liquidsISO 7233:2006, Rubber and plastics hoses and hose assemblies Determination of resistance to vacuumISO 7326:2006, Rubber and plastics hoses Assessment of ozone resista

36、nce under static conditionsISO 10088:1), Small craft Permanently installed fuel systemsEN 14214:2008+Amd.1:2009, Automotive fuels Fatty acid methyl esters (FAME) for diesel engines Requirements and test methods3 General requirementsHoses complying with this International Standard shall present a non

37、-porous, smooth inner surface, free from defects and chemical contaminants.Hoses shall demonstrate suitability for marine use by complying with the requirements of the tests in Clause 5. They shall be marked according to Clause 6.4 Nominal boreTable 1 gives some of the inner diameters based on serie

38、s R 10 of ISO 3:1973. Tolerances shall conform to ISO 1307 or the values given in Table 1.1) To be published. ISO 2013 All rights reserved 1BS EN ISO 7840:2013ISO 7840:2013(E)Table 1 Inner diameters and tolerancesDimensions in millimetresInner diameter, d Tolerance3,245 0,56,3789,51012,5161920 0,752

39、531,538 1,25405063 1,55 Physical tests on finished hose5.1 GeneralNew samples shall be used for each of the tests below.5.2 Test liquidsa) Petrol:1) by volume 100 % liquid 2 specified in ISO 1817:2011, Table A.2;AND2) a mixture of by volume 90 % of liquid 2 specified in ISO 1817:2011, Table A.2, and

40、 10 % by volume of ethanol.b) Diesel:1) a mixture of by volume 90 % liquid F specified in ISO 1817:2011 and 10 % by volume of Fatty Acid Methyl Esters (FAME), specified in EN 14214:2008+Amd.1:2009.5.3 Bursting pressureFor each test liquid as specified in 5.2, fill three hoses or sample lengths from

41、the hoses and store them for 40 days in air at a temperature of 40 C 2 C.2 ISO 2013 All rights reservedBS EN ISO 7840:2013ISO 7840:2013(E)Empty the liquid out and fill the hoses or sample lengths with cold water; subject them to hydrostatic pressure as specified in ISO 1402.The bursting pressure sha

42、ll be at least 1,4 MPa for hoses with an inner diameter of 10 mm or less and 1,00 MPa for hoses with an inner diameter of more than 10 mm.5.4 Vacuum-collapse testCarry out the test in accordance with ISO 7233:2006, method A, using the test conditions specified in Table 2.Table 2 Pressure conditions

43、for the vacuum collapse testInner diameter, d mmVacuum kPad 10 8010 25 No test requiredThe test duration shall be 60 s and the diameter of the sphere 0,8 d (inner diameter of the hose). The sphere shall pass freely through the hose while under vacuum.5.5 Volume change in test liquidsDetermine the ch

44、ange in volume of the hose (tube and cover) by the procedure described in ISO 1817.Place the test pieces in test liquids as specified in 5.2 at a temperature of 40 C 2 C for 40 days.If the hose is made of a homogeneous compound (with or without reinforcement), the swelling shall not exceed 35 % by v

45、olume, as measured by displacement in water. For hose with an inner layer of fuel-resistant material and a cover of another material, mainly intended for weather and ozone resistance, the increase in volume shall not exceed 35 % for the tube and 120 % for the cover.5.6 Mass reduction of test hoseDet

46、ermine the reduction in mass of the inner layer by the procedure described in ISO 1817. Fill three hoses or submerge test pieces from the hoses with test liquids, as specified in 5.2, and store them for 40 days in air at a temperature of 40 C 2 C.The reduction in mass of the inner layer shall not ex

47、ceed 8 % of the initial mass of the test pieces.NOTE A reduction in mass of 8 % corresponds to a decrease in volume of approximately 10 %.5.7 Fire resistanceTest the hose in accordance with the method described in Annex A.5.8 Effect of ozoneThe hose shall be tested as described in ISO 7326:2006, Met

48、hod 1. The sample shall show no visible cracks at 7 magnification.5.9 Fuel permeationThe permeation rate for the hoses shall be determined according to the method specified in Annex B or an equivalent test method. The hoses shall be classified in the following way and marked in accordance with Claus

49、e 6:Type 1: hoses with a permeation rate of 100 g/m2or less per 24 h. ISO 2013 All rights reserved 3BS EN ISO 7840:2013ISO 7840:2013(E)Type 2: hoses with a permeation rate of over 100 g/m2per 24 h, up to and including 300 g/m2per 24 h.5.10 Cold-flex testFor straight hoses of 19 mm inside diameter and less, condition three hose samples for 5 h at 20 C 2 C. Flex in the cold chamber through 180 from the centreline to a diameter of 10 times the maximum outside diameter of the hose. The flexing shall take pla