BS EN ISO 28927-2-2009 Hand-held portable power tools - Test methods for evaluation of vibration emission - Wrenches nutrunners and screwdrivers《手持便携式电动工具 振动辐射的评估用试验方法 扳手、螺母机和螺丝刀》.pdf

《BS EN ISO 28927-2-2009 Hand-held portable power tools - Test methods for evaluation of vibration emission - Wrenches nutrunners and screwdrivers《手持便携式电动工具 振动辐射的评估用试验方法 扳手、螺母机和螺丝刀》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 28927-2-2009 Hand-held portable power tools - Test methods for evaluation of vibration emission - Wrenches nutrunners and screwdrivers《手持便携式电动工具 振动辐射的评估用试验方法 扳手、螺母机和螺丝刀》.pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO28927-2:2009ICS 13.160; 25.140.01; 25.140.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDHand-held portablepower tools Testmethods for evaluationof vibration emissionPart 2: Wrenches, nutrunners andscrewdrivers (ISO 28927-2:2009)Licensed Copy: Wang B

2、in, ISO/EXCHANGE CHINA STANDARDS, 10/06/2010 07:58, Uncontrolled Copy, (c) BSIThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2010. BSI 2010ISBN 978 0 580 59884 5Amendments/corrigenda issued since publicationDate CommentsBS EN ISO

3、 28927-2:2009National forewordThis British Standard is the UK implementation of EN ISO 28927-2:2009. It supersedes BS EN ISO 8662-7:1997 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MCE/8/-/2, Hand-held, non-electric power tools - Safety.A list of o

4、rganizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal oblig

5、ations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 10/06/2010 07:58, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 28927-2 December 2009 ICS 13.160; 25.140.10 Supersedes EN ISO 8662-7:1997English Version Hand-held portable power tools - Test methods fo

6、r evaluation of vibration emission - Part 2: Wrenches, nutrunners and screwdrivers (ISO 28927-2:2009) Machines moteur portatives - Mthodes dessai pour lvaluation de lmission de vibrations - Partie 2: Cls, boulonneuses et visseuses (ISO 28927-2:2009) Handgehaltene motorbetriebene Maschinen - Messverf

7、ahren zur Ermittlung der Schwingungsemission - Teil 2: Schrauber, Mutterndreher und Schraubendreher (ISO 28927-2:2009) This European Standard was approved by CEN on 14 December 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

8、his European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official version

9、s (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, B

10、ulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STAND

11、ARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 28927-2:2009: ELicensed Copy: Wang Bin, ISO/EXCH

12、ANGE CHINA STANDARDS, 10/06/2010 07:58, Uncontrolled Copy, (c) BSIBS EN ISO 28927-2:2009EN ISO 28927-2:2009 (E) 3 Foreword This document (EN ISO 28927-2:2009) has been prepared by Technical Committee ISO/TC 118 “Compressors and pneumatic tools, machines and equipment“ in collaboration with Technical

13、 Committee CEN/TC 231 “Mechanical vibration and shock” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall

14、be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 8662-7:1997.

15、This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directives. For relationship with EU Directives, see informative Annex ZA and ZB, which are integral parts of this document. Acco

16、rding to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latv

17、ia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 28927-2:2009 has been approved by CEN as a EN ISO 28927-2:2009 without any modification. Licensed Copy: Wang Bin

18、, ISO/EXCHANGE CHINA STANDARDS, 10/06/2010 07:58, Uncontrolled Copy, (c) BSIBS EN ISO 28927-2:2009EN ISO 28927-2:2009 (E) 4 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC This European Standard

19、 has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 98/37/EC, Machinery, amended by Directive 98/79/EC. Once this standard is cited in the Official

20、Journal of the European Union under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essenti

21、al Requirements of that Directive, except ER 1.7.4 d) and 2.2, and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the products falling within the scope of this standard. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 10/06/2010 07:58, Unc

22、ontrolled Copy, (c) BSIBS EN ISO 28927-2:2009EN ISO 28927-2:2009 (E) 5 Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the European Commission and the

23、 European Free Trade Association to provide one means of conforming to Essential Requirements of the New Approach Directive 2006/42/EC on machinery. Once this standard is cited in the Official Journal of the European Union under that Directive and has been implemented as a national standard in at le

24、ast one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essential Requirement of that Directive, except ER 2.2.1.1, and associated EFTA regulations. WARNING Other require

25、ments and other EU Directives may be applicable to the product(s) falling within the scope of this standard. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 10/06/2010 07:58, Uncontrolled Copy, (c) BSIBS EN ISO 28927-2:2009ISO 28927-2:2009(E) ISO 2009 All rights reserved iiiContents Page Fore

26、word iv Introductionvi 1 Scope1 2 Normative references1 3 Terms, definitions and symbols 2 3.1 Terms and definitions .2 3.2 Symbols3 4 Basic standards and vibration test codes 3 5 Description of the family of machines 3 6 Characterization of vibration7 6.1 Direction of measurement 7 6.2 Location of

27、measurements.7 6.3 Magnitude of vibration13 6.4 Combination of vibration directions13 7 Instrumentation requirements13 7.1 General .13 7.2 Mounting of transducers 13 7.3 Frequency weighting filter13 7.4 Integration time13 7.5 Auxiliary equipment 14 7.6 Calibration14 8 Testing and operating condition

28、s of the machinery14 8.1 General .14 8.2 Operating conditions 15 8.3 Other quantities to be specified.15 8.4 Attached equipment, work piece and task15 8.5 Operators18 9 Measurement procedure and validity19 9.1 Reported vibration values 19 9.2 Declaration and verification of the vibration emission va

29、lue .19 10 Measurement report 20 Annex A (informative) Model test report for vibration emission of wrenches, nutrunners and screwdrivers 21 Annex B (normative) Determination of uncertainty 23 Annex C (normative) Brake devices Assembly drawings and specification of parts.26 Bibliography39 Licensed Co

30、py: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 10/06/2010 07:58, Uncontrolled Copy, (c) BSIBS EN ISO 28927-2:2009ISO 28927-2:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies

31、). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and no

32、n-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Par

33、t 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting

34、 a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 28927-2 was prepared by Technical Committee ISO/TC 118, Compressors and pneumatic tools,

35、 machines and equipment, Subcommittee SC 3, Pneumatic tools and machines. This first edition of ISO 28927-2 cancels and replaces ISO 8662-7:1997, of which it constitutes a technical revision. The most important changes are vibration measurement in three axes and at both hand positions, new transduce

36、r positions, improved definition of transducer positions and orientation, and all types of screwdrivers and nutrunners, excepting one-shot nutrunners, now covered. ISO 29827 consists of the following parts, under the general title Hand-held portable power tools Test methods for evaluation of vibrati

37、on emission: Part 1: Angle and vertical grinders1) Part 2: Wrenches, nutrunners and screwdrivers Part 3: Polishers and rotary, orbital and random orbital sanders2) Part 4: Straight grinders3)1) Together with Part 4, replaces ISO 8662-4, Hand-held portable power tools Measurement of vibrations at the

38、 handle Part 4: Grinders. 2) Replaces ISO 8662-8, Hand-held portable power tools Measurement of vibrations at the handle Part 8: Polishers and rotary, orbital and random orbital sanders. 3) Together with Part 1, replaces ISO 8662-4, Hand-held portable power tools Measurement of vibrations at the han

39、dle Part 4: Grinders. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 10/06/2010 07:58, Uncontrolled Copy, (c) BSIBS EN ISO 28927-2:2009ISO 28927-2:2009(E) ISO 2009 All rights reserved v Part 5: Drills and impact drills4) Part 6: Rammers5) Part 7: Nibblers and shears6) Part 8: Saws, polishing

40、 and filing machines with reciprocating action and small saws with oscillating or rotating action7) Part 9: Scaling hammers and needle scalers8) Part 10: Percussive drills, hammers and breakers9) Part 11: Stone hammers10)4) Replaces ISO 8662-6, Hand-held portable power tools Measurement of vibration

41、s at the handle Part 6: Impact drills. Non-impacting drills now covered. 5) Replaces ISO 8662-9, Hand-held portable power tools Measurement of vibrations at the handle Part 9: Rammers. 6) Replaces ISO 8662-10, Hand-held portable power tools Measurement of vibrations at the handle Part 10: Nibblers a

42、nd shears 7) Replaces ISO 8662-12, Hand-held portable power tools Measurement of vibrations at the handle Part 12: Saws and files with reciprocating action and saws with oscillating or rotating action 8) Together with Part 11, replaces ISO 8662-14, Hand-held portable power tools Measurement of vibra

43、tions at the handle Part 14: Stone-working tools and needle scalers. 9) Replaces ISO 8662-2, Hand-held portable power tools Measurement of vibrations at the handle Part 2: Chipping hammers and riveting hammers, ISO 8662-3, Hand-held portable power tools Measurement of vibrations at the handle Part 3

44、: Rock drills and rotary hammers, and ISO 8662-5, Hand-held portable power tools Measurement of vibrations at the handle Part 5: Pavement breakers and hammers for construction work. Chipping and riveting hammers, rock drills and rotary hammers all covered. 10) Together with Part 9, replaces ISO 8662

45、-14, Hand-held portable power tools Measurement of vibrations at the handle Part 14: Stone-working tools and needle scalers. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 10/06/2010 07:58, Uncontrolled Copy, (c) BSIBS EN ISO 28927-2:2009ISO 28927-2:2009(E) vi ISO 2009 All rights reservedInt

46、roduction This document is a type-C standard as stated in ISO 12100. When requirements of this type-C standard are different from those which are stated in type-A or -B standards, the requirements of this type-C standard take precedence over the requirements of the other standards for machines that

47、have been designed and built according to the requirements of this type-C standard. The vibration test codes for portable hand-held machines given in ISO 28927 are based on ISO 20643, which gives general specifications for the measurement of the vibration emission of hand-held and hand-guided machin

48、ery. ISO 28927 specifies the operation of the machines under type-test conditions and other requirements for the performance of type tests. The structure/numbering of its clauses follows that of ISO 20643. The basic principle for transducer positioning first introduced in the EN 60745 series of Euro

49、pean standards is followed, representing a deviation from ISO 20643 for reasons of consistency. The transducers are primarily positioned next to the hand in the area between the thumb and the index finger, where they give the least disturbance to the operator gripping the machine. It has been found that vibrations generated by wrenches and nutrunners during tightening and unfastening of threaded fasteners vary considerably in typical use. For impact and impulse machines, this is l