BS EN ISO 24998-2008 Plastics laboratory ware - Single-use Petri dishes for microbiological procedures《塑料实验室器皿 微生物过程用单用途皮氏培养皿》.pdf

《BS EN ISO 24998-2008 Plastics laboratory ware - Single-use Petri dishes for microbiological procedures《塑料实验室器皿 微生物过程用单用途皮氏培养皿》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 24998-2008 Plastics laboratory ware - Single-use Petri dishes for microbiological procedures《塑料实验室器皿 微生物过程用单用途皮氏培养皿》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO24998:2008ICS 71.040.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlastics laboratoryware Single-usePetri dishes formicrobiologicalprocedures (ISO24998:2008)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/07/2010 08:10, Uncontrolled Copy,

2、 (c) BSIThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2010 BSI 2010ISBN 978 0 580 58562 3Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 24998:2008National forewordThis British Standard is the UK implementation

3、 of EN ISO 24998:2008.It supersedes BS 611-2:1990 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee LBI/36/1, Laboratory Glass and Plastics Apparatus.A list of organizations represented on this committee can be obtained onrequest to its secretary.This pub

4、lication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/07/2010 08:10, Uncontrolled Cop

5、y, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 24998November 2008ICS 71.040.20English VersionPlastics laboratory ware - Single-use Petri dishes formicrobiological procedures (ISO 24998:2008)Matriel de laboratoire en matire plastique - Botes dePetri usage unique pour mthodes microbio

6、logiques (ISO24998:2008)Laborgerte aus Kunststoff - Einmal-Petrischalen frmikrobiologische Verfahren (ISO 24998:2008)This European Standard was approved by CEN on 29 October 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

7、EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (Engl

8、ish, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, C

9、yprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOM

10、IT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 24998:2008: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDAR

11、DS, 08/07/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 24998:2008EN ISO 24998:2008 (E) 3 Foreword This document (EN ISO 24998:2008) has been prepared by Technical Committee ISO/TC 48 “Laboratory glassware and related apparatus“ in collaboration with Technical Committee CEN/TC 332 “Laboratory equi

12、pment“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the latest by May 2009. Attentio

13、n is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the

14、 following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia

15、, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 24998:2008 has been approved by CEN as EN ISO 24998:2008 without any modification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/07/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 24998:2008

16、ISO 24998:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Terms and definitions. 1 3 Principle of use . 1 4 Types 2 5 Material 2 6 Design and construction 2 6.1 General. 2 6.2 Dimensions 2 6.3 Rim on lid. 3 6.4 Compartments. 3 6.5 Venting. 3 7 Performance 4 7.1 Rigidi

17、ty. 4 7.2 Resistance to thermal distortion. 4 7.3 Resistance to fracture 4 7.4 Stability in stacking 4 8 Limitation of contamination. 4 9 Sterility and special microbiological states. 4 10 Packaging 5 11 Marking 5 Annex A (normative) Type test for rigidity 6 Annex B (normative) Type test for resista

18、nce to thermal distortion 8 Annex C (normative) Type test for resistance to fracture 9 Annex D (normative) Type test for stability in stacking. 10 Bibliography . 11 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/07/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 24998:2008ISO 24998:2008(E

19、) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body inte

20、rested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnica

21、l Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the t

22、echnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. I

23、SO shall not be held responsible for identifying any or all such patent rights. ISO 24998 was prepared by Technical Committee ISO/TC 48, Laboratory equipment, Subcommittee SC 6, Laboratory and volumetric ware. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/07/2010 08:10, Uncontrolled Copy

24、, (c) BSIBS EN ISO 24998:2008INTERNATIONAL STANDARD ISO 24998:2008(E) ISO 2008 All rights reserved 1Plastics laboratory ware Single-use Petri dishes for microbiological procedures 1 Scope This International Standard specifies requirements and test methods for plain, single-use Petri dishes for micro

25、biological use. This International Standard does not apply to products of similar design which may be used for cell or tissue culture purposes. Neither does it apply to dishes supplied ready loaded with microbiological media. NOTE Petri dishes are used for microbiological routine purposes in very la

26、rge numbers and consequently, are often handled by robotic equipment. Users of such equipment should satisfy themselves that the Petri dishes of any given manufacturer are suitable for use with such equipment and, if obtained from several sources, are compatible if mixed. 2 Terms and definitions For

27、 the purposes of this document, the following terms and definitions apply. 2.1 Petri dish combination of a dish with an accompanying loose-fitting lid, intended to preserve the microbiological integrity of its unused or in-use enclosed, interior space 2.2 dish shallow, cylindrical or square, open-to

28、pped container comprising a plane base with an integral outer wall NOTE The dish can be subdivided with internal dividers to form separate compartments. 2.3 lid cover of similar shape to, and larger size than the dish, over which it is placed, inverted, to enclose a working volume NOTE The underside

29、 of the lid can incorporate one or more small protuberances (venting protrusions) to facilitate free circulation of environmental gases. Lids without such protrusions are designed to impede such free circulation. 3 Principle of use Under environmentally controlled conditions, selected to avoid intro

30、duction of unwanted micro-organisms, the lid of the Petri dish is lifted and a quantity of microbiologically nutrient medium introduced (poured) into the dish. The dish is recovered and allowed to equilibrate with a predetermined environment. Under similarly suitable conditions, the lid is lifted ag

31、ain and a sample under investigation is then introduced onto the medium in the dish. Following closure and a period of storage under predetermined conditions, growth of any microorganisms originating from the sample may have occurred, enabling further study. NOTE Attention is drawn to potential nati

32、onal or regional regulations in respect of safe and environmentally compatible disposal of used Petri dishes. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/07/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 24998:2008ISO 24998:2008(E) 2 ISO 2008 All rights reserved4 Types Four types of d

33、ish are specified in this International Standard. Type A: circular dishes, without internal dividers, with or without venting protrusions in the lid Type B: circular dishes, with internal dividers, with or without venting protrusions in the lid Type C: square dishes, without internal dividers, with

34、or without venting protrusions in the lid Type D: square dishes, with internal dividers, with or without venting protrusions in the lid NOTE There can be variants of Type A to Type D in respect of design and construction as given in Clause 6. In that case, detailed specifications are given by the ma

35、nufacturer. 5 Material The Petri dish shall be made from microbiologically inert transparent plastic and may be self-coloured for batch identification purposes, or colourless. The finished dish shall be free from colour variation or discolouration and physical defects such as striations which may im

36、pair its use in microbiology. 6 Design and construction 6.1 General When subjected to visual examination, the Petri dish shall have no sharp edges, projection or surface roughness capable of cutting, puncturing or abrading the skin or gloves of the user, or damaging the packaging. The Petri dish sha

37、ll be free of holes which would permit leakage or compromising of microbiological integrity. The base of the dish and the closed face of the lid shall be planar, within the limits given in Table 1. 6.2 Dimensions The dimensions of the Petri dish shall conform to those given in Table 1 and, where app

38、licable, to other detailed dimensions given in 6.3 to 6.5. NOTE Manufacturing techniques are capable of yielding products conforming to very tight dimensional tolerances frequently closer than 0,02 mm on products of this order of size. It is for that reason, and to allow manufacturers freedom to inn

39、ovate designs, that dimensional tolerances are not specified for the major dimensions in Table 1, but ranges are given from within which manufacturers may choose their basic dimensions. This also allows for innovative wall designs incorporating rims or multiple angles to facilitate automated handlin

40、g. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/07/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 24998:2008ISO 24998:2008(E) ISO 2008 All rights reserved 3Table 1 Dimensions of Petri dishes Dimensions in millimetres Range for external dimension of dish Type Nominal size Diameter Lengt

41、h of side Range for external height of dish Range for external height of lid Range for lateral clearance between lid and dish (assembled) at point of contact Flatness: maximum permitted departure of base of dish and face of lid from plane A (circular) 60 54 to 65 13 to 17 7,5 to 10,5 1 to 3 1,0 90 8

42、5 to 91 13 to 17 7,5 to 10,5 1 to 3 1,0 100 95 to 105 13 to 17 7,5 to 10,5 1 to 3 1,5 A and B (circular) 140 138 to 144 13 to 21 7,5 to 10,5 2 to 4 1,5 100 101 to 104 17 to 21 7,5 to 10,5 1 to 3 1,5 C and D (square) 120 121 to 129 13 to 21 7,5 to 10,5 2 to 4 1,5 The flatness (see Table 1) shall be m

43、easured as: the maximum distance between any part of the top face of the base and a horizontal plane touching that face; the maximum distance between any part of the top face of the lid and a horizontal plane touching that face. 6.3 Rim on lid A slight rim may be provided on the outer, closed face o

44、f the lid, close to its circumference or, if square, its outer edge. This rim shall not exceed 1 mm in height. NOTE Such a rim is to discourage dishes within stacks from sliding over one another laterally. 6.4 Compartments If the dish has dividers to create internal compartments, the height of the d

45、ividers shall be between 50 % and 100 % of the height of the dish and shall not allow leakage between compartments. The number of compartments shall be stated in the labelling of primary packaging, see Clauses 10 and 11. 6.5 Venting As referred to in 2.3, one or more venting protuberances (protrusio

46、ns) may be moulded on the inside face of the lid, close to its wall. Such venting protrusions shall extend radially from the wall to exceed the maximum lateral clearance possible between the edge of the dish and the lid. Single venting protrusion shall have a height within the range 0,12 mm to 0,35

47、mm. Multiple venting protrusions shall be symmetrically disposed on the lid and shall have a height within the range 0,25 mm to 0,7 mm. The provision of venting shall be designated by the letter “V” in the marking of primary packages. See Clauses 10 and 11. Licensed Copy: Wang Bin, ISO/EXCHANGE CHIN

48、A STANDARDS, 08/07/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 24998:2008ISO 24998:2008(E) 4 ISO 2008 All rights reserved7 Performance 7.1 Rigidity 7.1.1 Lid When tested by the method described in Annex A, the internal diameter (for Type A and B) or the internal width (for Type C and D) of the l

49、id, measured in the direction of the applied force, shall not decrease by more than 1 mm. 7.1.2 Dish When tested by the method described in Annex A, the internal diameter (for Type A and B) or the internal width (for Type C and D) of the dish, measured in the direction of the applied force, shall not decrease by more than 2 mm. 7.2 Resistance to thermal distortion After being subjected to the test method described in Annex B, the dish shall retain the degree of flatness given in Table 1 and the dish shall not rock or spin on