BS EN ISO 17349-2016 Petroleum and natural gas industries Offshore platforms handling streams with high content of CO2 at high pressures《石油和天然气工业 高压力下二氧化碳含量较高的海上平台处理流》.pdf

《BS EN ISO 17349-2016 Petroleum and natural gas industries Offshore platforms handling streams with high content of CO2 at high pressures《石油和天然气工业 高压力下二氧化碳含量较高的海上平台处理流》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 17349-2016 Petroleum and natural gas industries Offshore platforms handling streams with high content of CO2 at high pressures《石油和天然气工业 高压力下二氧化碳含量较高的海上平台处理流》.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 17349:2016Petroleum and natural gas industries Offshore platforms handling streams with high content of CO2at high pressuresBS EN ISO 17349:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 17349:2016. The UK participati

2、on in its preparation was entrusted to Technical Committee PSE/17, Materials and equipment for petroleum, petrochemical and natural gas industries.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the ne

3、cessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 87251 8 ICS 75.020 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard

4、was published under the authority of the Standards Policy and Strategy Committee on 31 March 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 17349 March 2016 ICS 75.020 English Version Petroleum and natural gas i

5、ndustries - Offshore platforms handling streams with high content of CO2at high pressures (ISO 17349:2016) Industries du ptrole et du gaz naturel - Plates-formes en mer traitant des courants fort teneur en CO2 haute pression (ISO 17349:2016) Erdl-, petrochemische und Erdgasindustrie - Dampf mit hohe

6、m CO2 Gehalt bei hohen Drcken und hohen Durchflussraten - Richtlinien (ISO 17349:2016) This European Standard was approved by CEN on 10 January 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

7、of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germa

8、n). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia,

9、 Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and Unite

10、d Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN I

11、SO 17349:2016 E BS EN ISO 17349:2016EN ISO 17349:2016 (E) 3 European foreword This document (EN ISO 17349:2016) has been prepared by Technical Committee ISO/TC 67 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries“ in collaboration with Technical Co

12、mmittee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at

13、the latest by September 2016, and conflicting national standards shall be withdrawn at the latest by September 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying

14、any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Rep

15、ublic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 17349:2016 has been a

16、pproved by CEN as EN ISO 17349:2016 without any modification. BS EN ISO 17349:2016ISO 17349:2016(E)Foreword vIntroduction vi1 Scope . 12 Normative references 13 Terms and definitions . 24 Abbreviated terms 45 Overview of CO2-rich streams behaviour . 55.1 General . 55.2 Hydrate formation 55.3 CO2soli

17、d formation. 65.4 Flow metering 66 Blow down, depressuring and relieving of plant and equipment . 67 Flare and vent system configuration . 77.1 General . 77.2 System selection 77.3 System configuration . 87.3.1 Flare 87.3.2 Vent 98 Materials . 98.1 Corrosion . 98.1.1 General 98.1.2 Internal corrosio

18、n control by dehydration 98.1.3 CRAs . 108.1.4 Internal corrosion protecting chemicals 108.1.5 Internal organic coatings . 108.2 Brittle fracture 108.3 Ductile fracture 108.4 Lubricants 108.5 Non-metallic seals for CO2service 119 Safety .119.1 General 119.2 Impacts of the loss of containment of CO2-

19、rich streams .119.2.1 General. 119.2.2 Respiratory physiological parameters .129.2.3 Low temperature impact . 129.2.4 CO2-rich stream BLEVE . 129.3 Hazard identification and risk assessment and management 129.3.1 General. 129.3.2 Hazard identification.139.3.3 Risk assessment and management .139.4 Co

20、nsequence analysis 149.4.1 General. 149.4.2 CO2dispersion 149.4.3 Effects of cold CO2jet 149.5 CO2detection . 149.6 Strategies. 15Annex A (informative) Evaluation of EOS for CO2-rich streams 16Annex B (informative) Hydrate formation 22Annex C (informative) Water content specification .26 ISO 2016 Al

21、l rights reserved iiiContents PageBS EN ISO 17349:2016ISO 17349:2016(E)Annex D (informative) Depressuring of CO2-rich streams .33Annex E (informative) Configuration of flare and vent systems .37Annex F (informative) Boiling liquid expanding vapour explosion (BLEVE) 40Annex G (informative) Methodolog

22、y for evaluation of running ductile fracture 42Annex H (informative) Non-metallic materials for use in CO2service .44Annex I (informative) CO2toxicology information .45Bibliography .48iv ISO 2016 All rights reservedBS EN ISO 17349:2016ISO 17349:2016(E)ForewordISO (the International Organization for

23、Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the r

24、ight to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedur

25、es used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial r

26、ules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights iden

27、tified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation

28、on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information .The committee responsible for this document is

29、 ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries. ISO 2016 All rights reserved vBS EN ISO 17349:2016ISO 17349:2016(E)IntroductionIn recent years, the oil industry has been facing challenges in developing and operating high-CO2content of

30、fshore fields. The CO2-rich streams, separated from the produced natural gas, can be injected to enhance oil recovery from the reservoirs. Even in cases where the oil recovery increase is not so significant, operators have to consider the CO2-rich stream compression and injection, in order to avoid

31、its venting to the atmosphere.Main concerns comprise surface safety system and material selection areas, which lack specific standards and regulations for this scenario. The commercial tools available, for instance, to model the dispersion of gases, need to be validated for CO2and CO2/hydrocarbon mi

32、xtures, which have distinctive thermodynamic behaviour. This will affect the choice of materials and plant design.This International Standard addresses concepts and criteria for processing CO2-rich streams, as a supplement to existing standards for offshore installations.vi ISO 2016 All rights reser

33、vedBS EN ISO 17349:2016Petroleum and natural gas industries Offshore platforms handling streams with high content of CO2at high pressures1 ScopeThis International Standard contains provisions for design of topside facilities for offshore plants handling CO2-rich streams at high pressures; i.e. CO2mo

34、lar concentration above 10 %. The surface systems include usual offshore process unit operations, as shown in Figure 1.This International Standard is applicable only to topside facilities of fixed and floating oil and gas production offshore units up to the last barrier, such as an ESDV. Subsea prod

35、uction systems and Cryogenic CO2separation are not covered.NOTE This example is within the scope of this International Standard.Figure 1 Example of a Process Flow Diagram (in grey zone)2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and

36、 are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appliesISO 13702, Petroleum and natural gas industries Control and mitigation of fires and explosions on offs

37、hore production installations Requirements and guidelinesINTERNATIONAL STANDARD ISO 17349:2016(E) ISO 2016 All rights reserved 1BS EN ISO 17349:2016ISO 17349:2016(E)ISO 15156 (all parts), Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas productionI

38、SO 21457, Petroleum, petrochemical and natural gas industries Materials selection and corrosion control for oil and gas production systemsISO 23936-1, Petroleum, petrochemical and natural gas industries Non-metallic materials in contact with media related to oil and gas production Part 1: Thermoplas

39、ticsISO 23936-2:2011, Petroleum, petrochemical and natural gas industries Non-metallic materials in contact with media related to oil and gas production Part 2: ElastomersAPI STD 521, Pressure-relieving and Depressuring Systems, API Standard, January 20143 Terms and definitionsFor the purposes of th

40、is document, the following terms and definitions apply.3.1compressibility factorZthermodynamic property for modifying the ideal gas law to account for the real gas behaviour3.2corrosion resistant alloyCRAalloy intended to be resistant to general and localized corrosion by oil field environments that

41、 are corrosive to carbon steelsSOURCE: ISO 15156-1:2015, 3.63.3dense phasefluid state (supercritical or liquid) above critical pressure3.4equation of stateEOSthermodynamic equation describing the state of matter under a given set of physical conditions3.5free waterwater not dissolved in the CO2-rich

42、 streamNote 1 to entry: This can be pure water, water with dissolved salts, water wet salts, water glycol mixtures or other mixtures containing water.3.6gas-assisted flareflare with gas assistance system in order to increase gas net heating value3.7high-velocity tip flareflare with gas exit velociti

43、es higher than 122 m/s3.8high-velocity ventvent with gas exit velocities higher than 150 m/s2 ISO 2016 All rights reservedBS EN ISO 17349:2016ISO 17349:2016(E)3.9hydratesolid, crystalline compound of water and light hydrocarbons or CO2, in which the water molecules combine with the gas molecules to

44、form a solid3.10CRA cladmetallic coating of CRA in which the bond between the parent metal and liner is metallurgical3.11low-velocity tip flareflare with gas exit velocities lower than 122 m/s3.12low-velocity ventvent with gas exit velocities lower than 150 m/s3.13minimum design temperatureminimum t

45、emperature below which the application limits for the materials involved are exceeded3.14platformcomplete assembly, including structure, topsides, foundations and stationkeeping systemsSOURCE: ISO 19900:2013, 3.353.15rapid gas decompressionRGDdepressurizationexplosive decompressionrapid pressure-dro

46、p in a high pressure gas-containing system which disrupts the equilibrium between external gas pressure and the concentration of gas dissolved inside any polymer, with the result that excess gas tries to escape from the solution at points throughout the material, causing expansionSOURCE: ISO 23936-2

47、:2011, 3.1.103.16supercritical phasefluid state above critical pressure and temperature3.17topsidesstructures and equipment placed on a supporting structure (fixed or floating) to provide some or all of a platforms functionsNote 1 to entry: For a ship-shaped floating structure, the deck is not part

48、of the topsides.Note 2 to entry: For a jack-up, the hull is not part of the topsides.Note 3 to entry: A separate fabricated deck or module support frame is part of the topsides.SOURCE: ISO 19900:2013, 3.523.18triple pointtemperature and pressure where CO2exists as a gas, liquid and solid simultaneou

49、sly ISO 2016 All rights reserved 3BS EN ISO 17349:2016ISO 17349:2016(E)4 Abbreviated termsAIV acoustically induced vibrationBLEVE boiling liquid expanding vapour explosionBDV blow down valveCH4methaneCO2carbon dioxideCCR central control roomCRA corrosion resistant alloyEERS evacuation, escape and rescue strategyEOS equation of stateESD emergency shut downFES fire and explosion strategyGDU gas dehydration unitH2S hydrogen sulfideHC hydrocarbonHP high pressureHSE health, safety and environmentIDLH immediately dangerous