BS EN ISO 15015-2011 Plastics Extruded sheets of impact-modified acrylonitrilestyrene copolymers (ABS AEPDS and ASA) Requirements and test methods《塑料 冲击改良的丙烯腈苯乙烯共聚物挤压片材(ABS AEPDS和A.pdf

《BS EN ISO 15015-2011 Plastics Extruded sheets of impact-modified acrylonitrilestyrene copolymers (ABS AEPDS and ASA) Requirements and test methods《塑料 冲击改良的丙烯腈苯乙烯共聚物挤压片材(ABS AEPDS和A.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 15015-2011 Plastics Extruded sheets of impact-modified acrylonitrilestyrene copolymers (ABS AEPDS and ASA) Requirements and test methods《塑料 冲击改良的丙烯腈苯乙烯共聚物挤压片材(ABS AEPDS和A.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 15015:2011Plastics Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) Requirements and test methodsBS EN ISO 15015:2011 BRITISH ST

2、ANDARDNational forewordThis British Standard is the UK implementation of EN ISO 15015:2011. It supersedes BS EN ISO 15015:2007, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e P R I / 7 5 , P l a s t i c s a n d r u b b e r f i l m a n

3、d s h e e t s .A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 71138 1 ICS 83.140.10 C

4、ompliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2011.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUR

5、OPISCHE NORM EN ISO 15015 April 2011 ICS 83.140.10 Supersedes EN ISO 15015:2007English Version Plastics - Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) - Requirements and test methods (ISO 15015:2011) Plastiques - Plaques extrudes en copolymres dacrylonitri

6、le-styrne modifis choc (ABS, AEPDS ou ASA) - Exigences et mthodes dessai (ISO 15015:2011) Kunststoffe - Extrudierte Tafeln aus schlagzh-modifizierten Acrylnitril/Styrol-Copolymeren (ABS, AEPDS und ASA) - Anforderungen und Prfverfahren (ISO 15015:2011) This European Standard was approved by CEN on 31

7、 March 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be

8、obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to th

9、e CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembo

10、urg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights

11、 of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15015:2011: EBS EN ISO 15015:2011 EN ISO 15015:2011 (E) 3 Foreword This document (EN ISO 15015:2011) has been prepared by Technical Committee ISO/TC 61 “Plastics“ in collaboration with Technica

12、l Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at th

13、e latest by October 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 15015:2007. According to the

14、 CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

15、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 15015:2011 has been approved by CEN as a EN ISO 15015:2011 without any modification. BS EN ISO 15015:2011ISO 15015:

16、2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv 1 Scope1 2 Normative references1 3 Material .2 4 Requirements.2 4.1 Appearance 2 4.2 Dimensional tolerances 2 4.3 Properties.3 5 Test methods .4 5.1 Test specimens4 5.2 Delivery condition .5 5.3 Appearance 5 5.4 Dimensions 5 5.5 Densi

17、ty6 5.6 Mechanical properties.6 5.7 Thermal properties6 6 Designation 8 6.1 Example for ABS sheets.8 6.2 Example for ASA sheets in rolled form.8 7 Marking.9 Annex A (informative) Additional guide values .10 Bibliography11 BS EN ISO 15015:2011ISO 15015:2011(E) iv ISO 2011 All rights reservedForeword

18、ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical

19、committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of elect

20、rotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the

21、member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for ident

22、ifying any or all such patent rights. ISO 15015 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products. This second edition cancels and replaces the first edition (ISO 15015:2007), of which it constitutes a minor revision in which the temperature in Tables 2, 3 and A.2

23、 at which the Charpy impact strength of notched specimens is measured has been changed from 20 C to +23 C. BS EN ISO 15015:2011INTERNATIONAL STANDARD ISO 15015:2011(E) ISO 2011 All rights reserved 1Plastics Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) Requ

24、irements and test methods 1 Scope This International Standard specifies the requirements and test methods for solid flat extruded sheets of impact-modified acrylonitrile-styrene copolymer materials: acrylonitrile-butadiene-styrene (ABS), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) (comm

25、only known as AES) and acrylonitrile-styrene-acrylate (ASA), without fillers or reinforcing materials. This International Standard also applies to ABS, AEPDS and ASA sheet in rolled form. It applies only to thicknesses from 0,25 mm to 20,0 mm. 2 Normative references The following referenced document

26、s are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 179-1, Plastics Determination of Charpy impact properties Part 1: Non-instrume

27、nted impact test ISO 179-2, Plastics Determination of Charpy impact properties Part 2: Instrumented impact test ISO 291, Plastics Standard atmospheres for conditioning and testing ISO 306:2004, Plastics Thermoplastic materials Determination of Vicat softening temperature (VST) ISO 527-2, Plastics De

28、termination of tensile properties Part 2: Test conditions for moulding and extrusion plastics ISO 1183 (all parts), Plastics Methods for determining the density of non-cellular plastics ISO 2039-1, Plastics Determination of hardness Part 1: Ball indentation method ISO 2580-1, Plastics Acrylonitrile-

29、butadiene-styrene (ABS) moulding and extrusion materials Part 1: Designation system and basis for specifications ISO 2818, Plastics Preparation of test specimens by machining ISO 6402-1, Plastics Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acryl

30、onitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials Part 1: Designation system and basis for specifications ISO 6603-1:2000, Plastics Determination of puncture impact behaviour of rigid plastics Part 1: Non-instrumented impact testing ISO 11501, Plastics Film and sheet

31、ing Determination of dimensional change on heating BS EN ISO 15015:2011ISO 15015:2011(E) 2 ISO 2011 All rights reserved3 Material Sheets shall be made of either ABS extrusion materials as defined in ISO 2580-1 or AEPDS (AES) or ASA extrusion materials as defined in ISO 6402-1, without fillers or rei

32、nforcing materials. The extrusion materials can contain additives such as processing aids, stabilizers, flame-protective agents and colorants. Compounds and additives of unknown identity shall not be used. NOTE Legal conditions might necessitate a specific choice of extrusion material (see 4.3.3). 4

33、 Requirements 4.1 Appearance Sheets shall be substantially free from bubbles, voids, cracks, visible impurities and other defects which would make them unfit for the intended use. Surfaces shall be substantially smooth, if not embossed, and free from grooves, sink marks or damage. Colorants shall be

34、 homogeneously distributed throughout the material. Slight colour variations due to variations in the extrusion compound or processing conditions are admissible. The exact extent of variations in any of the above, as well as gloss level specifications, if required, shall be agreed between the intere

35、sted parties. Sheets shall be examined in accordance with 5.3. 4.2 Dimensional tolerances 4.2.1 Thickness Within any delivery of sheets, the maximum thickness variation from the nominal value, h1, in millimetres, shall satisfy the requirement h1 u (0,03 mm + 0,04 hn) (1) where hnis the nominal sheet

36、 thickness, in millimetres. Within any individual sheet, the maximum thickness variation, h2, in millimetres, shall satisfy the requirement h2 u (0,03 mm + 0,02 hn) (2) Testing shall be in accordance with 5.4.1. 4.2.2 Length and width The nominal length, ln, and nominal width, bn, of sheets shall be

37、 as agreed between the interested parties. Unless agreed differently, the length shall be in the direction of extrusion. For any individual sheet selected at random from any delivery, the tolerances on length and width shall be in accordance with Table 1. Testing shall be in accordance with 5.4.2. T

38、able 1 Tolerances on length and width of sheets Values in millimetres Tolerances Nominal dimension DnLength Width Dnu 1 000 31+21+Dn 1 000 3n3101l+ 3n2101b+ For rolled sheets, the minimum length shall be the nominal length. BS EN ISO 15015:2011ISO 15015:2011(E) ISO 2011 All rights reserved 34.2.3 Re

39、ctangularity For any individual sheet selected at random from any delivery, the rectangularity tolerance, expressed as the difference in length of the diagonals, d1 d2 (see Figure 1), shall satisfy the requirement d1 d2 u 2 103 (ln2+ bn2) (3) Figure 1 Difference in length of diagonals, d1 d2 Testing

40、 shall be in accordance with 5.4.3. 4.2.4 Bow of sheets in rolled form For sheets in rolled form, a maximum bow of 20 mm in a 10 m length is permissible. Testing shall be in accordance with 5.4.4. 4.3 Properties 4.3.1 Mechanical and thermal properties The basic mechanical and thermal properties shal

41、l be as specified in Tables 2 and 3. Guide values of other properties of extruded ABS, AEPDS (AES) and ASA sheets are given in Tables A.1 and A.2 in Annex A. Table 2 Mechanical and thermal properties ABS Requirements (average values) for Property Unit ABS-NIaABS-HIaTest method subclause Tensile stre

42、ss at yield, yMPa W 35 W 30 5.6.1 Tensile modulus, EtMPa W 2 100 W 1 800 5.6.2 Charpy impact strength of unnotched specimens, acu, at 20 CbkJ/m2W 40 W 60 5.6.3 Charpy impact strength of notched specimens, acn, at +23 CbkJ/m2W 10 W 15 5.6.4 50 % impact-failure energy, E50, at hn= 4 mm J W 30 W 55 5.6

43、.5 Mechanical properties Ball indentation hardness, HB (test load 358 N) N/mm2W 80 W 60 5.6.6 Thermal properties Vicat softening temperature, VST (force 50 N, heating rate 50 C/h) C 90 to 105 85 to 105 5.7.1 aNI: normal impact, HI: high impact. bOnly valid for nominal sheet thicknesses hnW 4 mm (see

44、 also 5.1.1). BS EN ISO 15015:2011ISO 15015:2011(E) 4 ISO 2011 All rights reservedTable 3 Mechanical and thermal properties AEPDS (AES) and ASA Requirements (average values) for Property Unit AEPDS ASA Test method subclause Tensile stress at yield, yMPa W 30 W 30 5.6.1 Tensile modulus, EtMPa W 1 700

45、 W 1 500 5.6.2 Charpy impact strength of unnotched specimens, acu, at 20 CakJ/m2W 60 W 80 5.6.3 Charpy impact strength of notched specimens, acn, at +23 CakJ/m2W 25 W 30 5.6.4 50 % impact-failure energy, E50, at hn= 4 mm J W 60 W 60 5.6.5 Mechanical properties Ball indentation hardness, HB (test loa

46、d 358 N) N/mm2W 70 W 60 5.6.6 Thermal properties Vicat softening temperature, VST (force 50 N, heating rate 50 C/h) C 85 to 105 85 to 105 5.7.1 aOnly valid for nominal sheet thicknesses hnW 4 mm (see also 5.1.1). 4.3.2 Behaviour on heating The maximum shrinkage in the direction of extrusion shall no

47、t exceed the values given in Table 4 when measured using the method specified in 5.7.2 under the conditions given in Table 6. The test specimens shall be substantially free from bubbles and cracks after heating. Table 4 Maximum shrinkage for thermoforming applications Nominal thickness, hn0,25 mm 0,

48、5 mm 1 mm 2 mm 4 mm 8 mm 8 mm Max. shrinkage in the direction of extrusion 35 % 22 % 16 % 12 % 8 % 6 % Not relevant Intermediate values for other sheet thicknesses can be calculated by interpolation. 4.3.3 Physiological behaviour Relevant legislation concerning physiological behaviour shall be taken

49、 into consideration. 5 Test methods 5.1 Test specimens 5.1.1 Preparation of test specimens Representative test specimens shall be cut both longitudinally and transversely from locations evenly distributed over the length and width of the sheet. With sheets in rolled form, a 2 m sample shall be cut from the end of the roll to prepare test specimens. The surfaces of the test specimens shall be free from damage and faults in order