BS EN ISO 14692-1-2017 Petroleum and natural gas industries Glass-reinforced plastics (GRP) piping Vocabulary symbols applications and materials《石油和天然气工业 玻璃纤维增强塑料(GRP)管道 词汇、符号、应用和材.pdf

《BS EN ISO 14692-1-2017 Petroleum and natural gas industries Glass-reinforced plastics (GRP) piping Vocabulary symbols applications and materials《石油和天然气工业 玻璃纤维增强塑料(GRP)管道 词汇、符号、应用和材.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 14692-1-2017 Petroleum and natural gas industries Glass-reinforced plastics (GRP) piping Vocabulary symbols applications and materials《石油和天然气工业 玻璃纤维增强塑料(GRP)管道 词汇、符号、应用和材.pdf（80页珍藏版）》请在麦多课文档分享上搜索。

1、Petroleum and natural gas industries - Glass-reinforced plastics (GRP) pipingPart 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2017)BS EN ISO 14692-1:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE N

2、ORM EN ISO 14692-1 September 2017 ICS 75.200; 83.140.30 Supersedes EN ISO 14692-1:2002English Version Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2017) Industries du ptrole et du gaz naturel - Ca

3、nalisations en plastique renforc de verre (PRV) - Partie 1: Vocabulaire, symboles, applications et matriaux (ISO 14692-1:2017) Erdl- und Erdgasindustrie - Glasfaserverstrkte Kunststoffrohrleitungen (GFK) - Teil 1: Begriffe, Symbole, Anwendungen und Werkstoffe (ISO 14692-1:2017) This European Standar

4、d was approved by CEN on 22 June 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

5、national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own l

6、anguage and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Gre

7、ece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR

8、 NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14692-1:2017 ENational forewordThis British Standard is the UK implementation of EN ISO 14692-1:2017

9、. It is identical to ISO 14692-1:2017. It supersedes BS EN ISO 14692-1:2002, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PSE/17/-/6, Processing equipment and systems for petroleum and natural gas industries.A list of organizations represented on th

10、is committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 94759 9ICS

11、 75.200; 01.040.75; 83.140.30Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2017.Amendments/corrigenda issued since publicationDate Text affected BRI

12、TISH STANDARDBS EN ISO 146921:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14692-1 September 2017 ICS 75.200; 83.140.30 Supersedes EN ISO 14692-1:2002English Version Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applicati

13、ons and materials (ISO 14692-1:2017) Industries du ptrole et du gaz naturel - Canalisations en plastique renforc de verre (PRV) - Partie 1: Vocabulaire, symboles, applications et matriaux (ISO 14692-1:2017) Erdl- und Erdgasindustrie - Glasfaserverstrkte Kunststoffrohrleitungen (GFK) - Teil 1: Begrif

14、fe, Symbole, Anwendungen und Werkstoffe (ISO 14692-1:2017) This European Standard was approved by CEN on 22 June 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without

15、any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other lang

16、uage made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmar

17、k, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COM

18、MITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14692-1:2017 EBS EN

19、ISO 146921:2017EN ISO 14692-1:2017 (E) 3 European foreword This document (EN ISO 14692-1:2017) has been prepared by Technical Committee ISO/TC 67 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries“ in collaboration with Technical Committee CEN/TC 12

20、 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Mar

21、ch 2018 and conflicting national standards shall be withdrawn at the latest by March 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This docum

22、ent supersedes EN ISO 14692-1:2002. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugosla

23、v Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 14692-1:

24、2017 has been approved by CEN as EN ISO 14692-1:2017 without any modification. ISO 14692-1:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 23 Terms, definitions, symbols and abbreviated terms . 24 Pressure rating 224.1 MPRxx. 224.2 Part factors and partial factors. 254.2.1 Part fac

25、tor f2for loading . 254.2.2 Part factor f3,estfor the limited axial load capability of GRP piping .254.2.3 Partial factor A0for design life 254.2.4 Partial factor A2for chemical resistance 254.2.5 Partial factor A3for cyclic loading .255 Classification .255.1 Joints . 255.1.1 Unrestrained joints .25

26、5.1.2 Classification of joints 265.2 Resin matrix . 266 Materials 277 Dimensions 28Annex A (informative) Principle 30Annex B (informative) Guidance on scope limitations .36Annex C (normative) Enquiry sheet .37Annex D (normative) Wall thickness definitions 40Annex E (informative) Selection of part fa

27、ctor f3,estin the bid process 42Annex F (informative) Worked example 48Bibliography .67 ISO 2017 All rights reserved iiiContents PageBS EN ISO 146921:2017ISO 14692-1:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 23 Terms, definitions, symbols and abbreviated terms . 24 Pressure r

28、ating 224.1 MPRxx. 224.2 Part factors and partial factors. 254.2.1 Part factor f2for loading . 254.2.2 Part factor f3,estfor the limited axial load capability of GRP piping .254.2.3 Partial factor A0for design life 254.2.4 Partial factor A2for chemical resistance 254.2.5 Partial factor A3for cyclic

29、loading .255 Classification .255.1 Joints . 255.1.1 Unrestrained joints .255.1.2 Classification of joints 265.2 Resin matrix . 266 Materials 277 Dimensions 28Annex A (informative) Principle 30Annex B (informative) Guidance on scope limitations .36Annex C (normative) Enquiry sheet .37Annex D (normati

30、ve) Wall thickness definitions 40Annex E (informative) Selection of part factor f3,estin the bid process 42Annex F (informative) Worked example 48Bibliography .67 ISO 2017 All rights reserved iiiContents PageBS EN ISO 146921:2017ISO 14692-1:2017(E)ForewordISO (the International Organization for Stan

31、dardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right

32、 to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures u

33、sed to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules

34、 of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identifi

35、ed during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on t

36、he voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.

37、html.This document was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and systems.This second edition cancels and replaces the first edition (ISO 14692-1:2002), w

38、hich has been technically revised.A list of all parts of ISO 14692 can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 146921:2017ISO 14692-1:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO membe

39、r bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmenta

40、l and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance ar

41、e described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is d

42、rawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or o

43、n the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expres

44、sions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 67, Materials, e

45、quipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and systems.This second edition cancels and replaces the first edition (ISO 14692-1:2002), which has been technically revised.A list of all parts of ISO 14692 can be foun

46、d on the ISO website.iv ISO 2017 All rights reserved ISO 14692-1:2017(E)Introduction0.1 GeneralThe objective of ISO 14692 (all parts) is to provide the oil and gas industry, as well as the supporting engineering and manufacturing industry, with mutually agreed specifications and recommended practice

47、s for the purchase, qualification, manufacturing, design, handling, storage, installation, commissioning and operation of GRP piping systems.This document, provides guidance in the use and interpretation of the other parts of ISO 14692. This document contains the following annexes: Annex A (informat

48、ive) explaining the principle; Annex B (informative) providing guidance on scope limitations; Annex C (normative) containing the enquiry sheet; Annex D (normative) providing wall thickness definitions; Annex E (informative) describing selection of part factor f3,estin bid process; Annex F (informati

49、ve) containing a worked example.0.2 Basic steps in use of ISO 14692 (all parts)Figure 1 identifies the eight basic steps involved in the use of ISO 14692 (all parts) that are further explained below.Step 1: The bid process. The principal completes an enquiry sheet (see Annex C) that defines the design pressures and temperatures of the piping system as well as the application, required pipe sizes and required components (bends, tees, reducers, flanges, etc.). The principal also verifies that the scope of the application is within the limit