BS EN ISO 14530-3-2000 Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Requirements for selected moulding compounds《塑料 不饱和聚酯粉末模塑化合物(UP-PMCs) 对所选模塑化合物的要求》.pdf

《BS EN ISO 14530-3-2000 Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Requirements for selected moulding compounds《塑料 不饱和聚酯粉末模塑化合物(UP-PMCs) 对所选模塑化合物的要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 14530-3-2000 Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Requirements for selected moulding compounds《塑料 不饱和聚酯粉末模塑化合物(UP-PMCs) 对所选模塑化合物的要求》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN ISO 14530-3:2000 Th

2、e European Standard EN ISO 14530-3:1999 has the status of a British Standard ICS 83.080.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 3: Requirements for selected moulding compoundsThis British Standa

3、rd, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 January 2000 BSI 01-2000 ISBN 0 580 35887 9 BS EN ISO 14530-3:2000 Amendments issued since publication Amd. No. D

4、ate Comments National foreword This British Standard is the English language version of EN ISO 14530-3:1999. It is identical with ISO 14530-3:1999. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the

5、 responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the U

6、K. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding Europ

7、ean publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A Bri

8、tish Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a fro

9、nt cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.EN ISO 14530-3:19

10、99 Referencenumber ISO14530-3:1999(E) INTERNATIONAL STANDARD ISO 14530-3 Firstedition 1999-11-15 PlasticsUnsaturated-polyesterpowder mouldingcompounds(UP-PMCs) Part3: Requirementsforselectedmoulding compounds Plastiques Poudres mouler base de polyester non satur (UP-PMC) Partie 3: Exigences relative

11、s certaines poudres mouler EN ISO 14530-3:1999ISO-035413:(9991E) ISO9991 Allrgihtsresvrede.lnUesstorehwisescepfieid,noraptofthisilbupctaoinmaybeudorpercedorutziliedinnayformorbynaysnaem,electnoric ormecinahcal,inclidungtohpociypongnadmicrfoilm,wituohteprmissioninwritingfromeitehrISOattherddaesslebow

12、orISOsmemebrydob inthectnuoryofthertseuqee.r ISOcirypohgtfofice aCsesoptale56 121-HC1veneGa20 leT.+41224790111 aFx+41223741097 E-mailcirypothgiso.ch Webwww.iso.ch ii DPFdcsilremia ihTsPDFfilemayctnoainemeddebdtyfepaces.InaccnadrocewithAebodslicensinglopicy,thisfilemaybepirntedorivewedubtslahlton bei

13、detedlnuessthetyfepaceswhichareemeddebdraelicensedtonadintslaledonthecomputerfrepormingtheideting.Inodwlnidaongthis feli,trapiesaccepttierehnthesersnoptilibiyofontinfrnignigAebodslicsneniglopicy.hTeISOtneCarlSecterairatacceptsnollibaiityinthis .aera AbodeisatdaremarkofAbodeStsyemsInctaropro.de teDai

14、lsofthesfotwraepudorctsusedtocrtaeetihsPDFfilecanbefnuodintheGarenelInfolerativetothefile;theP-FDcerationrapamteers weretpoimizedforpirtning.EvreycraeahseebntakentoensruethatthefileissuitlbaeforusebyISOmemebridobse.Inthelnuikleyetnev tahtaplboremleratingtoitisfdnuo,lpaeseifnormthetneCarlSecterairata

15、ttheserddasgivenlebow. EN ISO 14530-3:1999ISO-035413:(9991E)iii Foreword ISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinter

16、estedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnon-governmental,in liaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotec

17、hnicalstandardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastin

18、gavote. AttentionisdrawntothepossibilitythatsomeoftheelementsofthispartofISO14530maybethesubjectof patentrights.ISOshallnotbeheldresponsibleforidentifyinganyorallsuchpatentrights. InternationalStandardISO14530-3waspreparedbyTechnicalCommitteeISO/TC61, Plastics, Subcommittee SC12, Thermosetting mater

19、ials. ISO14530consistsofthefollowingparts,underthegeneraltitle Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs): Part 1: Designation system and basis for specifications Part 2: Preparation of test specimens and determination of properties Part 3: Requirements for selected moulding

20、compounds AnnexAofthispartofISO14530isforinformationonly. EN ISO 14530-3:1999EN ISO 14530-3:1999INTERNATIONAL STANDARD ISO 14530-3:1999(E) ISO 9991 All irhgts seredevr 1 Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 3: Requirements for selected moulding compounds 1 Scope Th

21、is part of ISO 14530 specifies the requirements for the physical and chemical properties of unsaturated-polyester powder moulding compounds (UP-PMCs) and compression- or injection-moulded test specimens produced from them. It is limited to those powder moulding compounds whose composition and proper

22、ties are significantly different. It is further limited to those moulding compounds which are of general technical and/or economic importance. The properties which are used to characterize the moulding compounds, the test methods and the test conditions are selected from those given in ISO 14530-2.

23、The moulding compounds are divided into types according to their composition and properties. The various types are designated using the designation system defined in ISO 14530-1. 2 Normative references The following normative documents contain provisions which, through reference in this text, consti

24、tute provisions of this part of ISO 14530. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 14530 are encouraged to investigate the possibility of applying the most recent editions of the

25、 normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 472:1999, Plastics Vocabulary. ISO 14530-1:1999, Plastics Unsaturated-polyester po

26、wder moulding compounds (UP-PMCs) Part 1: Designation system and basis for specifications. ISO 14530-2:1999, Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 2: Preparation of test specimens and determination of properties. 3 Terms and definitions For the purposes of this part

27、 of ISO 14530, the terms and definitions given in ISO 472, ISO 14530-1 and ISO 14530-2 apply. EN ISO 14530-3:1999 1ISO -035413:(9991E) 2 ISO 9991 All irhgts seredevr 4 Requirements 4.1 Property values In order for an unsaturated-polyester powder moulding compound to be considered as complying with t

28、his part of ISO 14530, it shall meet the requirements given in Table 1. Table 1 gives the mean value obtained for the set of test specimens used to determine a particular property. Individual values of properties 2.1, 2.2, 2.3 and 2.4 shall be within 10 % of the mean value, and individual values of

29、properties 3.1 and 3.2 shall be within 5 C of the mean value. No specific limits are placed on rheological and processing properties. However, suitable rheological and processing properties are essential for the satisfactory use of a moulding compound. The test methods and test conditions used shall

30、 be as agreed between the interested parties. In addition, for some applications, it may be useful for information to be made available on other properties, for example: cure time; particle size; moisture content. If this is so, these properties and test methods, as well as the test conditions to be

31、 used, shall be as agreed between the interested parties. 4.2 Filler/reinforcement type and content In order for a phenolic powder moulding compound to be considered as complying with this part of ISO 14530, the nature, form and content by mass of its filler/reinforcement shall be as given in the de

32、signation of the moulding compound (see ISO 14530-1:1999, subclause 4.2). EN ISO 14530-3:1999 2ISO -035413:(9991E) ISO 9991 All irhgts seredevr 3 Table 1 Property requirements for UP-PMCs containing (GF+MD) or (LD+MD) as filler 1234 Type: PMC ISO 14530-UP. . . Property Unit Pro- cess- ing a Max. or

33、min. (GF10+MD60) to (GF20+MD50) (GF10+MD65),X,F to (GF20+MD55),X,F (LD20+MD50) to (LD30+MD40) 1 Rheological and processing properties 1.1 To be agreed between the interested parties 2 Mechanical properties 2.1 Stress at break, B MPa Q M W W 35 45 35 45 25 35 2.2 Flexural strength, fM MPa Q M W W 80

34、100 80 1000 70 80 2.3 Charpy impact strength, a cU kJ/m 2 Q M W W 5,0 7,5 5,0 7,5 4,5 5,0 2.4 Charpy notched impact strength, a cA kJ/m 2 Q M W W 1,1 1,3 1,1 1,3 1,0 1,0 3 Thermal properties 3.1 Temperature of deflection under load, T f 1,8 C Q/M W 250 250 110 3.2 Temperature of deflection under loa

35、d, T f 8,0 C Q/M W 180 180 70 3.3 Flammability (glow bar), BH Q / Mu BH 2-95 BH 2-10 BH 2-30 4 Electrical properties 4.1 Dissipation factor, tan 100 Q / Mu 0,03 0.03 4.2 Volume resistivity, e cm Q/M W 10 13 10 13 10 11 4.3 Surface resistivity, e Q/M W 10 12 10 12 10 10 4.4 Proof tracking index, PTI

36、Q/M W 600 600 600 5 Other properties 5.1 mg u 50 50 200 5.2 Water absorption, W w 24 %b y mass Q/M u a Q = Compression moulding M = Injection moulding NOTE 1 See ISO 14530-2:1999, Tables 3 and 4, columns 3, 4, and 7, for the methods to be used for the preparation of test specimens and the determinat

37、ion of properties. NOTE 2 In view of the differences between the property-value limits for compression-moulding and injection-moulding materials, the likely variations in test results and the wide range of properties covered, it should not be assumed that materials having the same designation are ex

38、actly equivalent. EN ISO 14530-3:1999 3ISO -035413:(9991E) 4 ISO 9991 All irhgts seredevr Annex A (informative) Comparison of designations Table A.1 Comparison of designations used for UP-PMCs in national and international standards 1234 National or international standard Type: PMC ISO 14530-UP. . .

39、 ISO 14530-3:1999 (GF10+MD60) to (GF20+MD50) (GF10+MD65),X,F to (GF20+MD55),X,F (LD20+MD50) to (LD30+MD40) ISO ASTM BS DIN 16911:1978 802 804 JIS NF EN ISO 14530-3:1999 4BS EN ISO 14530-3:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

40、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standar

41、ds. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constan

42、t aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:

43、020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Custome

44、r Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informati

45、on on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996

46、7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in al

47、l BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means el

48、ectronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.