BS EN ISO 13385-1-2011 Geometrical product specifications (GPS) Dimensional measuring equipment Callipers Design and metrological characteristics《产品几何技术规范(GPS) 尺寸测量设备 卡尺 设计和计量特性》.pdf

《BS EN ISO 13385-1-2011 Geometrical product specifications (GPS) Dimensional measuring equipment Callipers Design and metrological characteristics《产品几何技术规范(GPS) 尺寸测量设备 卡尺 设计和计量特性》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 13385-1-2011 Geometrical product specifications (GPS) Dimensional measuring equipment Callipers Design and metrological characteristics《产品几何技术规范(GPS) 尺寸测量设备 卡尺 设计和计量特性》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 13385-1:2011Geometrical productspecifications (GPS) Dimensional measuringequipmentPart 1: Callipers; Design and metrologicalcharacteristics (ISO 13385-1:2011)BS EN ISO 13385-1:2011Incorporating corrigendum October 2015BS EN ISO 13385-1:2011 BRITISH STANDARDNational

2、 forewordThis British Standard is the UK implementation of EN ISO 13385-1:2011. It partially supersedes BS 887:2008.The UK participation in its preparation was entrusted by Technical Committee TDW/4, Technical Product Realization, to Subcommittee TDW/4/4, Technical Product Realization - Gauging and

3、Measurement Equipment.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 201

4、5. Published by BSI Standards Limited 2015ISBN 978 0 580 92206 0ICS 17.040.30Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2011.Amendments/corrigenda

5、 issued since publicationDate Text affected31 October 2015 Supersession information in National foreword updatedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13385-1 July 2011 ICS 17.040.30 English Version Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1

6、: Callipers; Design and metrological characteristics (ISO 13385-1:2011) Spcification gomtrique des produits (GPS) - quipement de mesurage dimensionnel - Partie 1: Pieds coulisse; caractristiques de conception et caractristiques mtrologiques (ISO 13385-1:2011) Geometrische Produktspezifikation (GPS)

7、- Lngenmessgerte - Teil 1: Messschieber; Konstruktionsmerkmale und messtechnische Anforderungen (ISO 13385-1:2011) This European Standard was approved by CEN on 28 April 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eur

8、opean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versio

9、ns (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, B

10、elgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN C

11、OMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 13385-1:2011: EBS EN ISO 13385

12、-1:2011EN ISO 13385-1:2011 (E) 3 Foreword This document (EN ISO 13385-1:2011) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specificat

13、ions and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withdrawn at the latest

14、by January 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national stand

15、ards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P

16、oland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 13385-1:2011 has been approved by CEN as a EN ISO 13385-1:2011 without any modification. BS EN ISO 13385-1:2011EN ISO 13385-1:2011 (E) 3 Foreword This document (EN ISO

17、13385-1:2011) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specifications and verification” the secretariat of which is held by AFNOR

18、. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withdrawn at the latest by January 2012. Attention is drawn to the possibility that some

19、 of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to imple

20、ment this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swi

21、tzerland and the United Kingdom. Endorsement notice The text of ISO 13385-1:2011 has been approved by CEN as a EN ISO 13385-1:2011 without any modification. BS EN ISO 13385-1:2011EN ISO 13385-1:2011 (E) 3 Foreword This document (EN ISO 13385-1:2011) has been prepared by Technical Committee ISO/TC 21

22、3 “Dimensional and geometrical product specifications and verification” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specifications and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national

23、 standard, either by publication of an identical text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withdrawn at the latest by January 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent r

24、ights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia

25、, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of

26、ISO 13385-1:2011 has been approved by CEN as a EN ISO 13385-1:2011 without any modification. BS EN ISO 13385-1:2011ISO 13385-1:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Design characteristics 2 4.1 G

27、eneral design and nomenclature 2 4.2 Dimensions 4 4.3 Types of indicating devices .4 4.4 Measuring faces 7 5 Metrological characteristics.7 5.1 General .7 5.2 Effect of slider locking7 5.3 Maximum permissible error of indication (limited by MPE)7 5.4 MPE and MPL for a number of metrological characte

28、ristics 8 6 Indication in product documentation and data sheets8 7 Proof of conformance with specifications9 7.1 General .9 7.2 Measurement standards for the calibration of metrological characteristics9 8 Marking.10 Annex A (informative) Error tests11 Annex B (informative) Advice on application.14 A

29、nnex C (informative) Examples of different types of callipers.15 Annex D (informative) Examples of types of measurements .16 Annex E (informative) Data sheet (example)17 Annex F (informative) Calibration of metrological characteristics18 Annex G (informative) Relation to the GPS matrix model 19 Bibl

30、iography21 BS EN ISO 13385-1:2011ISO 13385-1:2011(E) iv ISO 2011 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out thro

31、ugh ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collabor

32、ates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standa

33、rds. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of t

34、his document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13385-1 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. This first edition of ISO 13385-1, toget

35、her with ISO 13385-2, cancels and replaces ISO 3599:1976 and ISO 6906:1984, which have been technically revised. ISO 13385 consists of the following parts, under the general title Geometrical product specifications (GPS) Dimensional measuring equipment: Part 1: Callipers; Design and metrological cha

36、racteristics Part 2: Calliper depth gauges; Design and metrological characteristics BS EN ISO 13385-1:2011ISO 13385-1:2011(E) ISO 2011 All rights reserved vIntroduction This part of ISO 13385 is a geometrical product specification (GPS) standard and is to be regarded as a general GPS standard (see I

37、SO/TR 14638). It influences chain link 5 of the chains of standards on size and distance in the general GPS matrix. The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this

38、document and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this document unless otherwise indicated. For more detailed information on the relation of this part of ISO 13385 to other standards and the GPS matrix model, see Annex G. BS EN ISO 13385-1:2

39、011BS EN ISO 13385-1:2011INTERNATIONAL STANDARD ISO 13385-1:2011(E) ISO 2011 All rights reserved 1Geometrical product specifications (GPS) Dimensional measuring equipment Part 1: Callipers; Design and metrological characteristics 1 Scope This part of ISO 13385 provides the most important design and

40、metrological characteristics of callipers with analogue indication: vernier scale or circular scale (dial), and with digital indication: digital display. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the e

41、dition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 14253-1, Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 1: Decision rules for proving conformance or non-

42、conformance with specifications ISO 14253-2:2011, Geometrical product specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification ISO 1497

43、8:2006, Geometrical product specifications (GPS) General concepts and requirements for GPS measuring equipment IEC 60529, Degrees of protection by enclosures (IP Code) ISO/IEC Guide 98-3, Uncertainty of measurement Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) ISO/IEC Guid

44、e 99, International vocabulary of metrology Basic and general concepts and associated terms (VIM) BS EN ISO 13385-1:2011ISO 13385-1:2011(E) 2 ISO 2011 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 14978, ISO/IEC Guide 99, and the

45、 following apply. 3.1 calliper measuring instrument which gives the evaluation of a dimensional quantity of an internal or external feature on the basis of the movement of a slider with a measuring jaw, moving relative to a measuring scale on a rigid beam and a fixed jaw See Figures 1 and 2. NOTE 1

46、Callipers with an additional measuring face at the end of the beam and a depth measuring rod are used for depth measurements (see Figure 1). NOTE 2 The indication may be either analogue (vernier), circular scale or digital. Regarding digital data transfer, see 4.3.3. NOTE 3 See Annex C for examples

47、of different types of callipers. NOTE 4 See Annex D for examples of several types of measurements. 3.2 measuring face contact contact between the measuring face and a feature of a workpiece 3.2.1 full measuring face contact contact between the full area of the measuring face and a feature of a workp

48、iece 3.2.2 partial measuring face contact contact between a partial area of the measuring face and a feature of a workpiece 3.2.3 measuring face line contact contact between a line, perpendicular to the length of the jaws, on the measuring face and a feature of a workpiece NOTE Form deviations in ei

49、ther the measuring face(s) or the feature are disregarded for the purposes of these definitions. 4 Design characteristics 4.1 General design and nomenclature The general design and workmanship of the calliper shall be such that its metrological characteristics comply with this part of ISO 13385 under all operational orientations unless otherwise specified by the manufacturer. See Figures 1 and 2 for general design. BS EN ISO 13385-1:2011ISO 13385-1:2011(E) ISO 2011 All rights reserved 3Key 1 beam 7 depth measuring ro