BS EN ISO 10673-2009 Plain washers for screw and washer assemblies - Small normal and large series - Product grade A《螺钉和垫圈组件用平垫圈 小号、标准和大号系列 产品级别A》.pdf

《BS EN ISO 10673-2009 Plain washers for screw and washer assemblies - Small normal and large series - Product grade A《螺钉和垫圈组件用平垫圈 小号、标准和大号系列 产品级别A》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 10673-2009 Plain washers for screw and washer assemblies - Small normal and large series - Product grade A《螺钉和垫圈组件用平垫圈 小号、标准和大号系列 产品级别A》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO10673:2009ICS 21.060.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlain washers forscrew and washerassemblies Small,normal and large series Product grade ALicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (

2、c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 28 February2010. BSI 2010ISBN 978 0 580 62289 2Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 10673:2009National forewordThis British Standard is the UK implementation of

3、 EN ISO 10673:2009.It supersedes BS EN ISO 10673:1999 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9/3, Product standards for fasteners.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publicat

4、ion does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c)

5、 BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 10673July 2009ICS 21.060.30 Supersedes EN ISO 10673:1998 English VersionPlain washers for screw and washer assemblies - Small, normaland large series - Product grade A (ISO 10673:2009)Rondelles plates pour vis rondelle plate incorpore -Sries

6、troite, normale et large - Grade A (ISO10673:2009)Flache Scheiben fr Kombi-Schrauben - Kleine, normaleund groe Reihe - Produktklasse A (ISO 10673:2009)This European Standard was approved by CEN on 20 June 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

7、the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists i

8、n three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies o

9、f Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN C

10、OMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 10673:2009: ELicensed Copy: Wang Bi

11、n, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO 10673:2009EN ISO 10673:2009 (E) 3 Foreword This document (EN ISO 10673:2009) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secre

12、tariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at the latest by January 2010. Attention is draw

13、n to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10673:1998. According to the CEN/CENELEC Internal Regulations, the nati

14、onal standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

15、Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 10673:2009 has been approved by CEN as a EN ISO 10673:2009 without any modification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrol

16、led Copy, (c) BSIBS EN ISO 10673:2009ISO 10673:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out t

17、hrough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO colla

18、borates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Sta

19、ndards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements o

20、f this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10673 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product standards for fasteners. This second edition cancels and replaces the f

21、irst edition (ISO 10673:1998), which has been technically revised. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO 10673:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO 10673

22、:2009INTERNATIONAL STANDARD ISO 10673:2009(E) ISO 2009 All rights reserved 1Plain washers for screw and washer assemblies Small, normal and large series Product grade A 1 Scope The International Standard specifies the characteristics of plain steel washers, small, normal and large series, of product

23、 grade A for metric screw and washer assemblies in accordance with ISO 10644. NOTE 1 The product can be manufactured under the conditions defined in Clause 5. NOTE 2 The manufacturing of screw and washer assemblies takes into consideration material and production procedure of screw and plain washer

24、as well as the assembly process of components, in order to meet specification requirements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest editi

25、on of the referenced document (including any amendments) applies. ISO 3269, Fasteners Acceptance inspection ISO 4759-3, Tolerances for fasteners Part 3: Plain washers for bolts, screws and nuts Product grades A and C ISO 6507-1, Metallic materials Vickers hardness test Part 1: Test method ISO 10644:

26、2009, Screw and washer assemblies made of steel with plain washers Washer hardness classes 200 HV and 300 HV 3 Classification Washers of product grade A for metric screw and washer assemblies are classified into three types: type S: small series, preferably for hexagon socket head cap screws and for

27、 cheese head screws. type N: normal series, preferably for hexagon head screws. type L: large series, preferably for hexagon head screws. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO 10673:2009ISO 10673:2009(E) 2 ISO 2009 All rights res

28、erved4 Dimensions 4.1 Washers type S For washers type S (small series), see Figure 1 and Table 1. Surface roughness in micrometres Figure 1 Washer type S Table 1 Dimensions of washer type S Dimensions in millimetres Nominal size Clearance hole d1Outside diameter d2Thickness h (Nominal thread diamete

29、r) d nom. (min.) max. nom. (max.) min. nom. max. min. 2 1,75 1,85 4,5 4,2 0,6 0,65 0,55 2,5 2,25 2,35 5 4,7 0,6 0,65 0,55 3 2,75 2,85 6 5,7 0,6 0,65 0,55 3,5 3,2 3,32 7 6,64 0,8 0,85 0,75 4 3,6 3,72 8 7,64 0,8 0,85 0,75 5 4,55 4,67 9 8,64 1 1,06 0,94 6 5,5 5,62 11 10,57 1,6 1,68 1,52 8 7,4 7,55 15 1

30、4,57 1,6 1,68 1,52 10 9,3 9,52 18 17,57 2 2,09 1,91 12 11 11,27 20 19,48 2 2,09 1,91 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO 10673:2009ISO 10673:2009(E) ISO 2009 All rights reserved 34.2 Washers type N For washers type N (normal se

31、ries), see Figure 2 and Table 2. Surface roughness in micrometres Figure 2 Washer type N Table 2 Dimensions of washer type N Dimensions in millimetres Nominal size Clearance hole d1Outside diameter d2Thickness h (Nominal thread diameter) d nom. (min.) max. nom. (max.) min. nom. max. min. 2 1,75 1,85

32、 5 4,7 0,6 0,65 0,55 2,5 2,25 2,35 6 5,7 0,6 0,65 0,55 3 2,75 2,85 7 6,64 0,6 0,65 0,55 3,5 3,2 3,32 8 7,64 0,8 0,85 0,75 4 3,6 3,72 9 8,64 0,8 0,85 0,75 5 4,55 4,67 10 9,64 1 1,06 0,94 6 5,5 5,62 12 11,57 1,6 1,68 1,52 8 7,4 7,55 16 15,57 1,6 1,68 1,52 10 9,3 9,52 20 19,48 2 2,09 1,91 12 11 11,27 2

33、4 23,48 2,5 2,6 2,4 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO 10673:2009ISO 10673:2009(E) 4 ISO 2009 All rights reserved4.3 Washers type L For washers type L (large series), see Figure 3 and Table 3. Surface roughness in micrometres

34、Figure 3 Washer type L Table 3 Dimensions of washer type L Dimensions in millimetres Nominal size Clearance hole d1Outside diameter d2Thickness h (Nominal thread diameter) d nom. (min.) max. nom. (max.) min. nom. max. min. 2 1,75 1,85 6 5,7 0,6 0,65 0,55 2,5 2,25 2,35 8 7,64 0,6 0,65 0,55 3 2,75 2,8

35、5 9 8,64 0,8 0,85 0,75 3,5 3,2 3,32 11 10,57 0,8 0,85 0,75 4 3,6 3,72 12 11,57 1 1,06 0,94 5 4,55 4,67 15 14,57 1 1,06 0,94 6 5,5 5,62 18 17,57 1,6 1,68 1,52 8 7,4 7,55 24 23,48 2 2,09 1,91 10 9,3 9,52 30 29,48 2,5 2,6 2,4 12 11 11,27 37 36,38 3 3,11 2,89 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA

36、STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO 10673:2009ISO 10673:2009(E) ISO 2009 All rights reserved 55 Requirements and reference International Standards See Table 4. Table 4 Requirements and reference International Standards Washer to be assembled Assembly in relation to screw

37、 heat treatment after heat treatment of the screw (see method 2 in ISO 10644) before heat treatment of the screw (see method 1 in ISO 10644) MaterialbSteel Heat treatable steel as agreed between screw manufacturer and washer supplier Hardness class 200 HV a300 HVa200 HVc300 HVcMechanical properties

38、Hardness ranged200 HV to 300 HV 300 HV to 370 HV 200 HV to 300 HV 300 HV to 370 HV Product grade AeTolerances International Standard ISO 4759-3 Finish Plain, i.e. washers to be supplied in natural finish or as agreed between screw manufacturer and washer supplier. All tolerances shall apply prior to

39、 the application of a plating or coating. Workmanship Parts shall be uniform in quality and free of irregularities or detrimental defects. No protruding burrs shall appear on the washer. Acceptability For the acceptance procedure, see ISO 3269. aHeat treated (HT) or work hardened (WH) to be defined

40、in the designation. In case of no specification, the washer manufacturer can choose freely. bOther materials as agreed between screw manufacturer and washer supplier. cHardness class after the heat treatment of the screw and washer assembly in accordance with ISO 10644. dHardness testing in accordan

41、ce with ISO 6507-1. Test force: HV 2 for nominal thicknesses h u 0,6 mm; HV 10 for nominal thicknesses 0,6 mm 1,2 mm. eProduct grade A does not apply to the tolerances of the clearance hole, d1, and the thickness, h. 6 Designation Plain washers shall be designated in accordance with the following ex

42、amples. EXAMPLE 1 A plain steel washer for screw and washer assemblies, type N (normal series), of nominal size 8 mm, hardness class 200 HV, work hardened (WH), manufactured by method 2 in accordance with ISO 10644:2009, Annex A, is designated as follows: Washer ISO 10673-N-8-200 HV WH Licensed Copy

43、: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO 10673:2009ISO 10673:2009(E) 6 ISO 2009 All rights reservedEXAMPLE 2 A plain steel washer for screw and washer assemblies, type N (normal series), of nominal size 8 mm, hardness class 200 HV, heat treated

44、(HT), manufactured by method 2 in accordance with ISO 10644:2009, Annex A, is designated as follows: Washer ISO 10673-N-8-200 HV HT EXAMPLE 3 A plain steel washer for screw and washer assemblies, type N (normal series), of nominal size 8 mm, made of 34CrMo4 steel (for example) and manufactured by me

45、thod 1 in accordance with ISO 10644:2009, Annex A, is designated as follows: Washer ISO 10673-N-8-34CrMo4 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO 10673:2009ISO 10673:2009(E) ISO 2009 All rights reserved 7Bibliography 1 ISO 6507-2,

46、Metallic materials Vickers hardness test Part 2: Verification and calibration of testing machines Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/06/2010 02:43, Uncontrolled Copy, (c) BSIBS EN ISO10673:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 900

47、1Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment o

48、r revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform

49、the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +4