BS EN ISO 10669-1999 Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A《自攻螺钉用平垫圈和垫圈组件 常规和大型系列 A级产品》.pdf

《BS EN ISO 10669-1999 Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A《自攻螺钉用平垫圈和垫圈组件 常规和大型系列 A级产品》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 10669-1999 Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A《自攻螺钉用平垫圈和垫圈组件 常规和大型系列 A级产品》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BSENISO 10669:1999 Plain washers for tapping screw and washer assemblies Normal and large series Product grade A The European Standard EN ISO 10669:1999 has the status of a British Standard ICS 21.060.30BSENISO10669:1999 ThisBritish Standard, having been prepared under the direction

2、of the Engineering SectorCommittee, was publishedunder the authorityofthe Standards Committee andcomes intoeffecton 15 November 1999 BSI 03-2000 ISBN 0 580 350037 National foreword This British Standard is the English language version of EN ISO 10669:1999. It is identical with ISO 10669:1999. The UK

3、 participation in its preparation was entrusted by Technical Committee FME/9, Bolts, nuts and accessories, to Subcommittee FME/9/6, General purpose fasteners and accessories, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European comm

4、ittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-r

5、eferences Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be f

6、ound in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standa

7、rds are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN ISO title page, page 2, the ISO title page, pages ii t

8、o iv, pages 1 to 4 anda back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd.No. Date CommentsBSENISO10669:1999 BSI 03-2000 i Contents

9、 Page National foreword Inside front cover Foreword 2 Foreword iii Text of ISO 10669 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10669 August 1999 ICS 21.060.00 English version Plain washers for tapping screw and washer assemblies Normal and large series Product grade A (ISO106

10、69:1999) Rondelles plates pour vis tle rondelle incorpore Sries normale et large Grade A (ISO10669:1999) Flache Scheiben fr Kombi-Blechschrauben Normale und groe Reihe Produktklasse A (ISO10669:1999) This European Standard was approved by CEN on 16 July 1999. CEN members are bound to comply with the

11、 CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or

12、 to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versi

13、ons. CEN members are the national standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europe

14、n de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10669:1999 EENISO10669:1999 BSI 03-2000 2 Foreword The text of the I

15、nternational Standard ISO10669:1999 has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Threaded and non-threaded mechanical fasteners and accessories”, the secretariat of which is held by DIN. This European Standard shall be given the

16、status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2000, and conflicting national standards shall be withdrawn at the latest by February 2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations o

17、f the following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of t

18、he International Standard ISO10669:1999 was approved by CEN as a European Standard without any modification. NOTENormative references to International Standards are listed in Annex ZA (normative).ENISO10669:1999 ii BSI 03-2000 Contents Page Foreword iii 1 Scope 1 2 Normative references 1 3 Classific

19、ation 1 4 Dimensions 1 5 Specifications and reference International Standards 3 6 Designation 3 Annex ZA (normative) Normative references to international publications with their relevant European publications 4 Figure 1 1 Figure 2 2 Table 1 2 Table 2 2 Table 3 3ENISO10669:1999 BSI 03-2000 iii Forew

20、ord ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a techni

21、cal committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of e

22、lectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requir

23、es approval by at least 75% of the member bodies casting a vote. International Standard ISO 10669 was prepared by Technical Committee ISO/TC 2, Fasteners.iv blankENISO10669:1999 BSI 03-2000 1 1 Scope This International Standard specifies the characteristics of plain steel washers of product grade A

24、for tapping screw and washer assemblies in accordance with ISO10510. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions o

25、f, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative do

26、cument referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 3269:, Fasteners Acceptance inspection 1) . ISO 4042:1999, Fasteners Electroplated coatings. ISO 4759-3:, Tolerances for fasteners Part3:Plain washers for bolts, screws and nuts Prod

27、uct grades A and C 2) . ISO 6507-1:1997, Metallic materials Vickers hardness test Part 1: Test method. ISO 10510:1999, Tapping screw and washer assemblies with plain washers 3 Classification Washers of product grade A for tapping screw and washer assemblies are classified into two types: Type N: Nor

28、mal series; Type L: Large series. 4 Dimensions 4.1 Type N, normal series See Figure 1 and Table 1. 1) To be published. (Revision of ISO 3269:1988) 2) To be published. (Revision of ISO 4759-3:1991) Figure 1 ENISO10669:1999 2 BSI 03-2000 Table 1 4.2 Type L, large series See Figure 2 and Table 2. Table

29、 2 Dimensions in millimetres Nominal size Clearance hole Outside diameter Thickness d 1 d 2 h (Nominal thread diameter, d) nom. (min.) max. nom. (max.) min. nom. max. min. 2,2 2,9 3,5 1,9 2,5 3 2 2,6 3,1 5 7 8 4,82 6,64 7,64 1 1 1 1,06 1,06 1,06 0,94 0,94 0,94 4,2 4,8 5,5 3,55 4 4,7 3,67 4,12 4,82 9

30、 10 12 8,64 9,64 11,57 1 1 1,6 1,06 1,06 1,68 0,94 0,94 1,52 6,3 8 9,5 5,4 7,15 8,8 5,52 7,3 8,95 14 16 20 13,57 15,57 19,48 1,6 1,6 2 1,68 1,68 2,09 1,52 1,52 1,91 Figure 2 Dimensions in millimetres Nominal size Clearance hole Outside diameter Thickness d 1 d 2 h (Nominal thread diameter, d) nom. (

31、min.) max. nom. (max.) min. nom. max. min. 2,2 2,9 3,5 1,9 2,5 3 2 2,6 3,1 7 9 11 6,64 8,64 10,57 1 1 1 1,06 1,06 1,06 0,94 0,94 0,94 4,2 4,8 5,5 3,55 4 4,7 3,67 4,12 4,82 12 15 15 11,57 14,57 14,57 1 1,6 1,6 1,06 1,68 1,68 0,94 1,52 1,52 6,3 8 9,5 5,4 7,15 8,8 5,52 7,3 8,95 18 24 30 17,57 23,48 29,

32、48 1,6 2 2,5 1,68 2,09 2,59 1,52 1,91 2,41ENISO10669:1999 BSI 03-2000 3 5 Specifications and reference International Standards See Table 3. Table 3 6 Designation EXAMPLEA plain steel washer for tapping screw and washer assemblies, normal series, of nominal size4,2 mm and hardness class 180 HV is des

33、ignated as follows: Washer ISO 10669 N 4,2 180 HV Material a Steel b Mechanical properties c Hardness class 180 HV Hardness range d 180 HV to 300 HV Tolerance Product grade A e International Standard ISO4759-3 Surface finish Plain, i.e. washers to be supplied in natural finish, treated with a protec

34、tive lubricant or with other coatings as agreed between customer and supplier. Requirements for electroplating are covered in ISO4042. All tolerances shall apply prior to the application of a plating or coating. Workmanship Parts shall be free of irregularities of detrimental defects. No protruding

35、burrs shall appear on the washer. Acceptability For the acceptance procedure see ISO 3269. a Other materials as agreed between customer and supplier. b The carbon content shall not exceed 0,12%. c The mechanical properties are for the as delivered condition only. They may change when the screw and w

36、asher assembly is hardened and tempered. d Hardness testing according to ISO 6507-1. Test force: HV 10 for nominal thickness h u 1,2 mm HV 30 for nominal thickness h 1,2 mm e Product grade A does not apply to the tolerance of the clearance hole d 1and the thickness h.ENISO10669:1999 4 BSI 03-2000 An

37、nex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the pu

38、blications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publikati

39、on Jahr Titel EN Jahr ISO 4042 1999 Fasteners Electroplated coatings EN ISO 4042 1999 ISO 6507-1 1997 Metallic materials Vickers hardness test Part1:Test method EN ISO 6507-1 1997 ISO 10510 1999 Tapping screw and washer assemblies with plain washers EN ISO 10510 1999blankBS EN ISO 10669:1999 BSI 389

40、 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated

41、 by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStan

42、dard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editio

43、ns of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have b

44、een published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also ava

45、ilable which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and othe

46、r benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents

47、 Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary de

48、tails such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.