BS EN ISO 10556-2009 Fibre ropes of polyester polyolefin dual fibres《聚酯 聚烯烃双纤维的纤维绳索》.pdf

《BS EN ISO 10556-2009 Fibre ropes of polyester polyolefin dual fibres《聚酯 聚烯烃双纤维的纤维绳索》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 10556-2009 Fibre ropes of polyester polyolefin dual fibres《聚酯 聚烯烃双纤维的纤维绳索》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO10556:2009ICS 59.080.50NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDFibre ropes ofpolyester/polyolefindual fibres (ISO10556:2009)This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 December2009 BSI

2、 2009ISBN 978 0 580 61723 2Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 10556:2009National forewordThis British Standard is the UK implementation of EN ISO 10556:2009.It supersedes BS EN 14686:2004 which is withdrawn.The UK participation in its preparation was entrusted to Te

3、chnicalCommittee TCI/77, Ropes and cordage and fishing nets.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compl

4、iance with a British Standard cannot confer immunityfrom legal obligations.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10556 December 2009 ICS 59.080.50 Supersedes EN 14686:2004English Version Fibre ropes of polyester/polyolefin dual fibres (ISO 10556:2009) Cordages en fibres bi-matriau

5、x polyester/polyolfines (ISO 10556:2009) Faserseile aus Polyester/Polyolefin-Doppelfaserseile (ISO 10556:2009) This European Standard was approved by CEN on 4 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europ

6、ean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (Englis

7、h, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,

8、Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATIO

9、N COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10556:2009: EBS EN ISO 10556:2009EN ISO 10556:2009 (E) 3

10、Foreword This document (EN ISO 10556:2009) has been prepared by Technical Committee ISO/TC 38 “Textiles“ in collaboration with Technical Committee CEN/TC 248 “Textiles and textile products” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standa

11、rd, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN an

12、d/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14686:2004. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria,

13、 Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement n

14、otice The text of ISO 10556:2009 has been approved by CEN as a EN ISO 10556:2009 without any modification. BS EN ISO 10556:2009ISO 10556:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (I

15、SO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, gov

16、ernmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC

17、 Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the membe

18、r bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10556 was prepared by Technical Committee ISO/TC 38, Textiles. BS EN ISO

19、 10556:2009BS EN ISO 10556:2009INTERNATIONAL STANDARD ISO 10556:2009(E) ISO 2009 All rights reserved 1Fibre ropes of polyester/polyolefin dual fibres 1 Scope This International Standard specifies requirements for 3-strand hawser-laid, 8-strand and 12-strand braided fibre ropes made of polyester in c

20、ombination with polyolefin, and gives rules for their designation. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

21、ment (including any amendments) applies. ISO 1968, Fibre ropes and cordage Vocabulary ISO 2307, Fibre ropes Determination of certain physical and mechanical properties ISO 9554:2005, Fibre ropes General specifications 3 Terms and definitions For the purposes of this document, the terms and definitio

22、ns given in ISO 1968 apply. 4 Designation Fibre ropes shall be designated by the following: the words “fibre rope”; the number of this International Standard; the construction or type of the rope (see Clause 6); the reference number of the rope; the materials from which the rope is made; the level o

23、f performance of the rope: fibre rope or higher-strength (hs) fibre rope. EXAMPLE 1 Designation of a 3-strand hawser-laid rope, reference number 20 (type A), corresponding to a linear density of 194 ktex, made of polyester/polyolefin dual fibre: Fibre rope ISO 10556 - A - 20 - polyester/polyolefin E

24、XAMPLE 2 Designation of a 12-strand braided rope, reference number 20 (type T), corresponding to a linear density of 221 ktex, made of higher-strength polyester/polyolefin dual fibre: Fibre rope ISO 10556 - T - 20 - polyester/polyolefin (hs) BS EN ISO 10556:2009ISO 10556:2009(E) 2 ISO 2009 All right

25、s reserved5 Materials 5.1 Fibres 5.1.1 Polyester: the polyester portion of the rope shall be a continuous multifilament, heat- and light- resistant fibre of industrial (high tenacity) grade. 5.1.2 Polyolefin: the polyolefin portion of the rope shall be of suitable tenacity to meet all the requiremen

26、ts of this International Standard. NOTE Polyolefin can be polypropylene, or a mixture of polypropylene and polyethylene with a minimum of 15 % and a maximum of 50 % of polyethylene. 5.2 Yarns 5.2.1 The cover yarns of each strand of fibre ropes shall be made with polyester fibres covering a polyolefi

27、n core and shall contain a minimum of 40 % by mass of polyester fibre (see Table 1). NOTE When interior yarns are used, they may consist of 100 % polyolefin fibres. 5.2.2 All the yarns used in higher-strength fibre ropes shall be made with polyester fibres covering a polyolefin core and shall contai

28、n a minimum of 40 % by mass of polyester fibre (see Table 2). 6 General requirements 6.1 Polyester/polyolefin dual-fibre ropes shall be constructed in one of the following ways: type A: 3-strand hawser-laid rope (see Figure 1); type L: 8-strand braided rope (see Figure 2); type T: 12-strand braided

29、rope (see Figure 3). Figure 1 Shape of a 3-strand hawser-laid rope (type A) BS EN ISO 10556:2009ISO 10556:2009(E) ISO 2009 All rights reserved 3Figure 2 Shape of an 8-strand braided rope (type L) aOne-plait pitch. Figure 3 Shape of a 12-strand braided rope (type T) 6.2 Construction, manufacture, lay

30、, labelling, packaging, invoicing and delivery lengths shall conform to ISO 9554. 7 Physical properties The linear density and minimum breaking force shall conform to Tables 1 and 2. BS EN ISO 10556:2009ISO 10556:2009(E) 4 ISO 2009 All rights reservedTable 1 Fibre ropes: 3-strand hawser-laid rope (t

31、ype A), 8-strand braided rope (type L) and 12-strand braided rope (type T) of polyester/polyolefin dual fibres Linear densitybcMinimum breaking forcedekN Reference numberaNominal ktex Tolerance % Unspliced ropes Ropes with eye-spliced terminations 6 17,5 6,8 6,1 8 31,0 10 11,9 10,7 10 48,5 18,2 16,4

32、 12 69,9 8 25,7 23,1 14 95,1 34,7 31,2 16 124 44,8 40,3 18 157 56,1 50,5 20 194 68,7 61,8 22 235 82,1 73,9 24 279 96,3 86,7 26 328 113 102 28 380 130 117 30 437 148 133 32 497 167 150 36 629 210 189 40 776 257 231 44 939 308 277 48 1 110 364 328 52 1 320 5 424 382 56 1 520 489 440 60 1 750 558 502 6

33、4 1 990 631 568 68 2 250 707 636 72 2 520 789 710 80 3 110 963 867 88 3 750 1 160 1 040 96 4 470 1 370 1 230 104 5 260 1 590 1 430 112 6 050 1 840 1 660 120 6 980 2 100 1 890 128 7 950 2 370 2 130 136 8 950 2 660 2 390 144 10 100 2 970 2 670 BS EN ISO 10556:2009ISO 10556:2009(E) ISO 2009 All rights

34、reserved 5Table 1 (continued) Linear densitybcMinimum breaking forcedekN Reference numberaNominal ktex Tolerance % Unspliced ropes Ropes with eye-spliced terminations 152 11 300 3 290 2 960 160 12 500 5 3 630 3 270 aThe reference number corresponds to the approximate diameter, in millimetres. bThe l

35、inear density, in kilotex, corresponds to the net mass per length of the rope, expressed in grams per metre or in kilograms per kilometre. cThe linear density is obtained under reference tension and is measured as specified in ISO 2307.dThe breaking forces relate to new, dry and wet ropes.eA force d

36、etermined by the test methods specified in ISO 2307 is not necessarily an accurate indication of the force at which that rope might break in other circumstances and situations. The type and quality of termination, the rate of force application, prior conditioning and previous force applications to t

37、he rope can significantly influence the breaking force. A rope bent around a post, capstan, pulley or sheave may break at a significantly lower force. A knot or other distortion in a rope may significantly reduce the breaking force. Table 2 Higher-strength fibre ropes: 3-strand hawser-laid rope (typ

38、e A), 8-strand braided rope (type L) and 12-strand braided rope (type T) of polyester/polyolefin dual fibres Linear densitybcMinimum breaking forcedekN Reference numberaNominal ktex Tolerance % Unspliced ropes Ropes with eye-spliced terminations 6 19,9 7,56 6,80 8 35,4 10 13,2 11,9 10 55,3 20,2 18,2

39、 12 79,6 8 28,6 25,7 14 108 38,5 34,7 16 142 49,8 44,8 18 179 62,3 56,1 20 221 76,3 68,7 22 268 91,2 82,1 24 319 107 96 26 374 5 125 113 28 434 144 130 30 498 164 148 32 566 186 167 36 717 233 210 40 885 285 257 44 1 070 342 308 BS EN ISO 10556:2009ISO 10556:2009(E) 6 ISO 2009 All rights reservedTab

40、le 2 (continued) Linear densitybcMinimum breaking forcedekN Reference numberaNominal ktex Tolerance % Unspliced ropes Ropes with eye-spliced terminations 48 1 270 404 364 52 1 500 471 424 56 1 730 543 489 60 1 990 620 558 64 2 270 701 631 68 2 560 786 707 72 2 870 877 789 80 3 540 1 070 963 88 4 280

41、 1 290 1 160 96 5 100 5 1 520 1 370 104 6 000 1 770 1 590 112 6 900 2 040 1 840 120 7 960 2 330 2 100 128 9 060 2 630 2 370 136 10 200 2 960 2 660 144 11 500 3 300 2 970 152 12 800 3 660 3 290 160 14 200 4 030 3 630 aThe reference number corresponds to the approximate diameter, in millimetres. bThe

42、linear density, in kilotex, corresponds to the net mass per length of the rope, expressed in grams per metre or in kilograms per kilometre. cThe linear density is obtained under reference tension and is measured as specified in ISO 2307.dThe breaking forces relate to new, dry and wet ropes.eA force

43、determined by the test methods specified in ISO 2307 is not necessarily an accurate indication of the force at which that rope might break in other circumstances and situations. The type and quality of termination, the rate of force application, prior conditioning and previous force applications to

44、the rope can significantly influence the breaking force. A rope bent around a post, capstan, pulley or sheave may break at a significantly lower force. A knot or other distortion in a rope may significantly reduce the breaking force. 8 Marking The marking shall be in accordance with Clause 6 of ISO

45、9554:2005. BS EN ISO 10556:2009BS EN ISO10556:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standa

46、rds in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our

47、products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.B

48、SI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fa

49、x: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its