BS EN ISO 4566-1995 Small craft with inboard engine - Propeller shaft ends and bosses with 1 10 taper《舱内机小艇 锥度为1 10螺旋浆轴端和轴毂》.pdf

《BS EN ISO 4566-1995 Small craft with inboard engine - Propeller shaft ends and bosses with 1 10 taper《舱内机小艇 锥度为1 10螺旋浆轴端和轴毂》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 4566-1995 Small craft with inboard engine - Propeller shaft ends and bosses with 1 10 taper《舱内机小艇 锥度为1 10螺旋浆轴端和轴毂》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 4566:1995 Small craft with inboard engine Propeller shaft ends and bosses with1:10 taper The European Standard EN ISO4566:1995 has the status of a British StandardBSENISO4566:1995 This British Standard, having been prepared under the directionof the Engineering SectorBoard

2、, was published underthe authority oftheStandards Board and comes into effect on 15 August1995 BSI11-1999 The following BSI references relate to the work on this standard: Committee reference GME/33 Draft for comment91/82889 DC ISBN 0 580 24549 7 Committees responsible for this British Standard The

3、preparation of this British Standard was entrusted to Technical Committee GME/33, Small craft, upon which the following bodies were represented: Consumer Policy Committee of BSI Department of Trade and Industry Department of Trade and Industry (Standards Policy Unit) Federation of Wire Rope Manufact

4、urers of Great Britain Fire Extinguishing Trades Association Home Office Lloyds Register of Shipping Marine Safety Agency National Rivers Authority Personal Watercraft Association Royal Ocean Racing Club Royal Society for the Prevention of Accidents Royal Yachting Association Coopted Members British

5、 Canoe Manufacturers Association British Marine Industries Federation British Nautical Instrument Trade Association British Waterways Board Amendments issued since publication Amd. No. Date CommentsBSENISO4566:1995 BSI 11-1999 i Contents Page Committees responsible Inside front cover National forewo

6、rd ii Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Dimensions 3 5 Construction details 3 6 Tolerances 3 7 Threads 3 8 Designation 3 Figure 1 4 Table 1 5 List of references Inside back coverBSENISO4566:1995 ii BSI 11-1999 National foreword This British Standard has been prepared by

7、 Technical Committee GME/33 and is the English language version of ENISO4566:1995 Small craft with inboard engine Propeller shaft ends and bosses with1:10 taper, published by the European Committee for Standardization (CEN). It is identical with ISO4566:1992 published by the International Organizati

8、on for Standardization (ISO). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-refer

9、ence Publication referred to Corresponding British Standard ISO1947:1973 BS4500 ISO limits and fits Part5:1988 Specification for system of cone tolerances for conical workpieces from C=1:3 to1:500 and lengths from6mm to630mm Summary of pages This document comprises a front cover, an inside front cov

10、er, pagesi andii, theENISOtitle page, pages2 to6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE

11、NORM EN ISO4566 April1995 ICS 47.080 Supersedes EN24566:1989 Descriptors: Shipbuilding, small craft, marine propellers, propeller shafts, shaft ends, hubs, dimensions, dimensional tolerances, designation English version Small craft with inboard engine Propeller shaft ends and bosses with1:10 taper (

12、ISO4566:1992) Navires de plaisance moteur intrier Extrmits darbres porte-hlices et moyeux dhlices avec une conicit de1:10 (ISO4566:1992) Kleine Wasserfahrzeuge mit Innenbordmotoren Propellerwellenenden und Propellernaben mit Kegel1:10 (ISO4566:1992) This European Standard was approved by CEN on1994-

13、10-25. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtain

14、ed on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secret

15、ariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee f

16、or Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref.No.ENISO4566:1995EENISO4566:1

17、995 BSI 11-1999 2 Foreword The text of the International Standard from ISO/TC188, Small craft, of the International Organization for Standardization (ISO) has been taken over as a European Standard by CEN/CS. This European Standard supersedes EN24566:1989. This European Standard shall be given the s

18、tatus of a national standard, either by publication of an identical text or by endorsement, at the latest by October1995, and conflicting national standards shall be withdrawn at the latest by October1995. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implem

19、ent this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom.ENISO4566:1995 BSI 11-1999 3 1 Scope This International Standard specifies the dimensions for interc

20、hangeability of propeller bosses (hubs) and propeller shaft ends in the shaft diameter range of20mm to160mm with a taper of1:10 1) , intended for installation on inboard-engined small craft. 2 Normative references The following standards contain provisions which, through reference in this text, cons

21、titute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of

22、 the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO/R773:1969, Rectangular or square parallel keys and their corresponding keyways (Dimensions in millimetres). ISO1947:1973, System of cone tolerances for conical workpieces from C=

23、1:3 to1:500 and lengths from6 to630mm. 3 Definitions For the purposes of this International Standard, the following definitions apply. 3.1 nominal diameter diameter of the large end of the shaft end taper, which is the same as the diameter of the cylindrical shaft, ignoring tolerances 3.2 taper coni

24、cal portion of the shaft end designed to accommodate a key to transmit the full propeller shaft torque to the propeller, while allowing for disassembly 4 Dimensions The dimensions shall be those shown in Figure 1 and Table 1. The “reference dimensions” indicated in the table shall be considered nomi

25、nal dimensions for guidance only. Configurations shown in Figure 1 not specified by dimensions in Table 1 are not essential to interchangeability and are therefore left to the discretion of the manufacturer. Nominal diameters without brackets shall be preferred; those in brackets are a second choice

26、. Thread diameters without brackets shall similarly be preferred; those in brackets are alternatives. 5 Construction details Details indicated in Figure 1 are not intended to restrict design; nor are they to scale. Types and methods of construction or machining of the key, the keyway and their corne

27、r radii, the thread undercut and the thread end, or of other optional details (i.e.safety pin hole, centring point, etc.) are left open for individual methods to comply with the configuration of the coupling and/or particular needs. The length of the thread l 2shall be equal to thread diameter d 2 .

28、 The part of the thread engaged by the propeller nut shall be not less than80% of the thread length l 2 . 6 Tolerances 6.1 Shaft end taper small diameter, d 1 The tolerances shall be as given in Table 1. The tolerance deviations are calculated from the nominal diameter. 6.2 Boss taper large diameter

29、, D The tolerances shall be as given in Table 1. 6.3 Cone angle The tolerances shall be cone diameter tolerances as in ISO1947 with tolerance ranges equal to the diameter tolerance ranges specified in6.1 and6.2 for diameters d 1and D respectively. 6.4 Keyways and keys The tolerances shall be those g

30、iven for normal keys in ISO/R773. 6.5 Boss length, l 1 The tolerance shall be 0,5mm. 7 Threads Propeller nuts and shaft ends shall use M-Fine threads. 8 Designation Both propeller shafts and bosses constructed in accordance with these requirements shall be designated by a reference to this Internati

31、onal Standard, and the nominal diameter. EXAMPLE Propeller boss ISO456635 1) ISO8845 (to be published) will cover propeller shaft ends and bosses machined to a taper of1:16.ENISO4566:1995 4 BSI 11-1999 NOTEl 2(thread length)=d 2 Part of thread engaged by nut=0,8 l 2 See clause5. Figure 1 ENISO4566:1

32、995 BSI 11-1999 5 Table 1 Dimensions in millimetres Nominal diameter Boss Shaft end taper Thread Key Reference dimension a Length Bore bigger diameter Small diameter Diameter Pitch End Width Depth D nom l 1 D d 1 d 2 P l 3 l 4 b h l 5 l 6 l 7 d 3 min. max. max. min. 20 22 25 30 50 50 60 80 20,000 22

33、,000 25,000 30,000 20,052 22,052 25,052 30,052 15,500 17,500 19,500 22,500 15,448 17,448 19,448 22,448 14 16 16 20 1,5 1,5 1,5 1,5 20 20 20 25 25 25 25 30 6 6 8 8 6 6 7 7 45 45 55 75 5 5 5 5 0 0 0 0 15 17 19 22 35 40 45 90 100 110 35,000 40,000 45,000 35,062 40,062 45,062 26,500 30,500 34,500 26,448

34、 30,448 34,438 24 24 30 2 2 2 30 30 35 35 35 40 10 12 14 8 8 9 85 95 105 5 5 5 0 0 0 26 30 34 50 (55) 60 120 130 140 50,000 55,000 60,000 50,062 55,074 60,074 38,500 43,000 47,000 38,438 42,926 46,926 36(30) 36 42 3 3 3 40 40 50 45 45 55 14 16 18 9 10 11 115 120 130 5 10 10 0 0 0 38 42 46 (65) 70 (7

35、5) 150 160 170 65,000 70,000 74,500 65,074 70,074 74,574 51,000 55,000 58,500 50,926 54,926 58,426 42 48 48 3 3 3 50 55 55 55 60 60 18 20 20 11 12 12 140 150 165 10 10 10 0 0 5 50 54 57 80 (85) 90 180 190 200 79,500 84,500 89,500 79,574 84,587 89,587 62,500 66,500 71,000 62,426 66,413 70,913 56 56 6

36、4(56) 4 4 4 65 65 70 70 70 75 22 22 25 14 14 14 175 185 190 10 10 15 5 5 5 61 65 69 (95) 100 110 210 220 240 94,500 99,000 109,000 94,587 99,087 109,087 75,000 78,500 86,500 74,913 78,413 86,413 64(56) 72(64) 80(72) 4 4 4 70 80 85 75 85 90 25 28 28 14 16 16 200 215 235 15 15 15 5 10 10 73 77 85 120

37、130 140 260 280 300 119,000 129,0 139,0 119,087 129,1 139,1 94,500 102,500 110,500 94,413 102,413 110,413 90(80) 100(90) 100(90) 4 4 4 90 100 100 95 105 105 32 32 36 18 18 20 255 275 295 15 15 15 10 10 10 93 101 109 150 160 320 340 149,0 159,0 149,1 159,1 118,500 126,500 118,413 126,413 110(100) 120

38、(110) 4 4 110 120 115 125 36 40 20 22 315 335 15 15 10 10 117 125 a For guidance only: see clause4.6 blankBSENISO4566:1995 BSI 11-1999 List of references See national foreword.BS EN ISO 4566:1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national

39、body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the lates

40、t amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can

41、 be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publica

42、tions should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provi

43、des a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:0

44、2089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyrig

45、ht subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form o

46、r by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.