BS EN ISO 3861-2008 Rubber hoses for sand and grit blasting - Specification《沙子和喷钢砂处理用橡胶软管 规范》.pdf

《BS EN ISO 3861-2008 Rubber hoses for sand and grit blasting - Specification《沙子和喷钢砂处理用橡胶软管 规范》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 3861-2008 Rubber hoses for sand and grit blasting - Specification《沙子和喷钢砂处理用橡胶软管 规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO3861:2008ICS 25.220.10; 83.140.40NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRubber hoses for sandand grit blasting Specification (ISO3861:2005)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/06/2009 06:45, Uncontrolled Copy, (c) BSIThis B

2、ritish Standard was published under theauthority of the StandardsPolicy and StrategyCommittee on 28 February 2009 BSI 2009ISBN 978 0 580 57641 6Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 3861:2008National forewordThis British Standard is the UK implementation of EN ISO 3861

3、:2008. Itis identical to ISO 3861:2005. It supersedes BS EN ISO 3861:1997 whichis withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/66, Rubber and plastics tubing, hoses and hoseassemblies.A list of organizations represented on this committee can be obtained o

4、nrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 0

5、4/06/2009 06:45, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 3861November 2008ICS 25.220.10; 83.140.40 Supersedes EN ISO 3861:1997 English VersionRubber hoses for sand and grit blasting - Specification (ISO3861:2005)Tuyaux en caoutchouc pour sablage et grenaillage

6、 -Spcifications (ISO 3861:2005)This European Standard was approved by CEN on 29 October 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date

7、lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the res

8、ponsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Ice

9、land, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Sta

10、ssart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 3861:2008: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/06/2009 06:45, Uncontrolled Copy, (c) BSIBS EN ISO 3861:2008EN ISO 3861:2008 (E)

11、 3 Foreword The text of ISO 3861:2005 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 3861:2008 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assembli

12、es” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the latest by May 2009. Attention is

13、 drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 3861:1997. According to the CEN/CENELEC Internal Regulations, the

14、national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norw

15、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 3861:2005 has been approved by CEN as a EN ISO 3861:2008 without any modification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/06/2009 06:45, Uncontr

16、olled Copy, (c) BSIBS EN ISO 3861:2008ISO 3861:2005(E) ISO 2005 All rights reserved iiiContents Page Foreword iv 1 Scope 1 2 Normative references . 1 3 Terms and definitions. 1 4 Classification. 2 5 Materials and construction 2 6 Dimensions 2 6.1 Internal diameters and tolerances. 2 6.2 Concentricit

17、y . 3 6.3 Tolerance on length 3 6.4 Minimum thickness of lining and cover 3 7 Physical properties . 3 7.1 Rubber compounds 3 7.2 Finished hoses 3 8 Marking. 4 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/06/2009 06:45, Uncontrolled Copy, (c) BSIBS EN ISO 3861:2008ISO 3861:2005(E) iv ISO

18、 2005 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested i

19、n a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commis

20、sion (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical

21、 committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall

22、 not be held responsible for identifying any or all such patent rights. ISO 3861 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics). This third edition cancels and replaces the second edition (ISO 3861:1995), which has been techn

23、ically revised. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/06/2009 06:45, Uncontrolled Copy, (c) BSIBS EN ISO 3861:2008INTERNATIONAL STANDARD ISO 3861:2005(E) ISO 2005 All rights reserved 1Rubber hoses for sand and grit blasting Specification WARNING Persons using this International S

24、tandard should be familiar with normal laboratory practice. This standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any national regulat

25、ory conditions. 1 Scope This International Standard specifies the requirements for rubber hoses for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 6,3 bar and over an operating temperature range of 25 C to +70 C. 2 Normative references The following referenc

26、ed documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile st

27、ress-strain properties ISO 188:1998, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests ISO 1307, Rubber and plastics hoses for general-purpose industrial applications Bore diameters and tolerances, and tolerances on length ISO 1402, Rubber and plastics hoses and hose a

28、ssemblies Hydrostatic testing ISO 1746:1998, Rubber or plastics hoses and tubing Bending tests ISO 4649:2002, Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum device ISO 4671, Rubber and plastics hoses and hose assemblies Methods of measureme

29、nt of dimensions ISO 4672:1997, Rubber and plastics hoses Sub-ambient temperature flexibility tests ISO 7326:1991, Rubber and plastics hoses Assessment of ozone resistance under static conditions ISO 8031, Rubber and plastics hoses and hose assemblies Determination of electrical resistance ISO 8033,

30、 Rubber and plastics hoses Determination of adhesion between components ISO 8330, Rubber and plastics hoses and hose assemblies Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions in ISO 8330 apply. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04

31、/06/2009 06:45, Uncontrolled Copy, (c) BSIBS EN ISO 3861:2008ISO 3861:2005(E) 2 ISO 2005 All rights reserved4 Classification Hoses are designated as one of the following grades depending on their electrical properties: a) Electrically bonded Designated and marked “M” grade. b) Electrically conductiv

32、e, using a conductive rubber layer Designated and marked “” grade. 5 Materials and construction The hose shall consist of: a rubber lining; a reinforcement of natural or synthetic textile, applied by any suitable technique; a rubber cover. Depending on the grade, the construction may contain a condu

33、ctive rubber layer or a bonding wire or wires consisting of at least nine strands of a metal having a high resistance to fatigue. The lining and cover shall be of uniform thickness, concentric to comply with the minimum thickness specified and free from holes, porosity and other defects. The cover f

34、inish may be smooth or fabric-marked. 6 Dimensions 6.1 Internal diameters and tolerances When measured in accordance with ISO 4671, the internal diameters and their tolerances shall conform to the values specified in Table 1. Table 1 Internal diameters and tolerances Internal diameter mm Tolerance m

35、m 12,5 0,75 16 0,75 19 0,75 20 0,75 25 1,25 31,5 1,25 38 1,50 40 1,50 45 1,50 50 1,50 51 1,50 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/06/2009 06:45, Uncontrolled Copy, (c) BSIBS EN ISO 3861:2008ISO 3861:2005(E) ISO 2005 All rights reserved 36.2 Concentricity When determined in acco

36、rdance with ISO 4671, the concentricity, based on a total indicator reading between the internal diameter and the outside surface of the cover, shall be no greater than 1,0 mm. 6.3 Tolerance on length When measured in accordance with ISO 4671, the tolerance on cut lengths shall be as specified in IS

37、O 1307. 6.4 Minimum thickness of lining and cover When measured in accordance with ISO 4671, the minimum thickness of the rubber lining shall be 5,0 mm and that of the cover 1,0 mm. 7 Physical properties 7.1 Rubber compounds When tested by the methods listed in Table 2, the physical properties of th

38、e compounds used for the lining and cover shall conform to the values specified in Table 2. Tests shall be carried out either on samples taken from the hose or from separately vulcanized sheets 2 mm thick for the tensile/elongation tests and thicker for the abrasion test. These shall be vulcanized t

39、o the same state of cure as production hoses. Table 2 Physical properties of thermoplastic materials Requirements Property Lining Cover Test method Minimum tensile strength 14,0 MPa 10,0 MPa ISO 37 (dumb-bell test piece) Minimum elongation at break 400 % 300 % ISO 37 (dumb-bell test piece) 25 % 25 %

40、 Resistance to ageing: Change in tensile strength from original value (max.) Change in elongation at break from original value (max.) between +10 % and 30 % between +10 % and 30 % ISO 188:1998 (3 days at 70 C 1 C), air-oven method;ISO 37 (dumb-bell test piece) Abrasion resistance (maximum loss) 140

41、mm3N/A ISO 4649:2002, method A 7.2 Finished hoses When measured by the methods listed in Table 3, the physical properties of finished hoses shall conform to the values specified in Table 3. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/06/2009 06:45, Uncontrolled Copy, (c) BSIBS EN ISO 3

42、861:2008ISO 3861:2005(E) 4 ISO 2005 All rights reservedTable 3 Physical properties of finished hoses Property Requirements Test method Proof pressure 12,5 bar ISO 1402 Change in length at proof pressure 8 % ISO 1402 Change in diameter at proof pressure 10 % ISO 1402 Twist at proof pressure 20 /m (ma

43、x.) ISO 1402 Minimum burst pressure 25 bar ISO 1402 Adhesion between components 2,0 kN/m (min.) ISO 8033 Ozone resistance No cracking observed under 2 magnification ISO 7326:1991, method 1 up to 25 mm ID method 2 or 3 for other sizes Flexibility at 23 C T/D not less than 0,8 ISO 1746:1998, method A

44、Low-temperature flexibility No cracks shall be detected and the hose shall pass the proof test specified above. ISO 4672:1997, method B, at 25 C 2 C Electrical resistance (max.) “M” grade: 102/length “” grade: 106/length ISO 8031 8 Marking The hose shall be continuously and durably marked with the f

45、ollowing minimum information: a) the manufacturers name or identification; b) the number and year of publication of this International Standard; c) the hose grade (“M” or “”); d) the internal diameter, in millimetres; e) the maximum working pressure, in bars; f) the quarter and year of manufacture.

46、EXAMPLE MAN/ISO 3861:2005/Grade “M”/25/6,3 bar/1Q05 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/06/2009 06:45, Uncontrolled Copy, (c) BSIBS EN ISO 3861:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/06/2009 06:45, Uncontrolled Copy, (c) BSIBS EN ISO3861:2008BSI GroupHead

47、quarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated

48、 by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an

49、 inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, internatio