BS EN ISO 3093-2009 Wheat rye and their flours durum wheat and durum wheat semolina - Determination of the falling number according to Hagberg-Perten《小麦、黑麦和其作物粉、硬粒小麦和硬粒小麦粉 根据哈格伯格-伯.pdf

《BS EN ISO 3093-2009 Wheat rye and their flours durum wheat and durum wheat semolina - Determination of the falling number according to Hagberg-Perten《小麦、黑麦和其作物粉、硬粒小麦和硬粒小麦粉 根据哈格伯格-伯.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 3093-2009 Wheat rye and their flours durum wheat and durum wheat semolina - Determination of the falling number according to Hagberg-Perten《小麦、黑麦和其作物粉、硬粒小麦和硬粒小麦粉 根据哈格伯格-伯.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO3093:2009ICS 67.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDWheat, rye andtheir flours, durumwheat and durumwheat semolina Determination ofthe falling numberaccording to Hagberg-Perten (ISO 3093:2009)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA ST

2、ANDARDS, 25/03/2010 06:53, Uncontrolled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 January2010 BSI 2010ISBN 978 0 580 67548 5Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 3093:2009National forewordThis

3、British Standard is the UK implementation of EN ISO 3093:2009. Itsupersedes BS EN ISO 3093:2007 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee AW/4, Cereals and pulses.A list of organizations represented on this committee can be obtained onrequest to i

4、ts secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:

5、53, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 3093 December 2009 ICS 67.060 Supersedes EN ISO 3093:2007English Version Wheat, rye and their flours, durum wheat and durum wheat semolina - Determination of the falling number according to Hagberg-Perten (ISO 309

6、3:2009) Bls tendres, seigles et leurs farines, bls durs et leurs semoules - Dtermination de lindice de chute selon Hagberg-Perten (ISO 3093:2009) Weizen, Roggen und deren Mehl, Hartweizen und Hartweizengrie - Bestimmung der Fallzahl nach Hagberg-Perten (ISO 3093:2009) This European Standard was appr

7、oved by CEN on 1 December 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationa

8、l standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and not

9、ified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M

10、alta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of ex

11、ploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 3093:2009: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:53, Uncontrolled Copy, (c) BSIBS EN ISO 3093:2009EN ISO 3093:2009 (E) 3 Foreword This document (EN ISO 3093:2009) has

12、been prepared by Technical Committee ISO/TC 34 “Food products“ in collaboration with Technical Committee CEN/TC 338 “Cereal and cereal products” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical t

13、ext or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible

14、for identifying any or all such patent rights. This document supersedes EN ISO 3093:2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republ

15、ic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 3093:2009 has been

16、 approved by CEN as a EN ISO 3093:2009 without any modification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:53, Uncontrolled Copy, (c) BSIBS EN ISO 3093:2009ISO 3093:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv 1 Scope1 2 Normative references1 3 Terms a

17、nd definitions .1 4 Principle2 5 Reagents.2 6 Apparatus.2 7 Sampling.3 8 Preparation of test sample .3 8.1 Whole grain 3 8.2 Flour and semolina samples 4 9 Procedure.4 9.1 Determination of the moisture content .4 9.2 Test portion4 9.3 Determination of falling number 5 9.4 Calculation .6 10 Precision

18、.7 10.1 Interlaboratory tests7 10.2 Repeatability 7 10.3 Reproducibility 7 11 Test report8 Annex A (normative) Equations for altitude correction of falling numbers .9 Annex B (informative) Results of interlaboratory tests 10 Bibliography13 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03

19、/2010 06:53, Uncontrolled Copy, (c) BSIBS EN ISO 3093:2009ISO 3093:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is nor

20、mally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in

21、the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepar

22、e International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. ISO draws attention to the fact that it is cla

23、imed that compliance with this document may involve the use of a patent concerning the falling number apparatus specified in 6.1. ISO takes no position concerning the evidence, validity and scope of this patent right. The holder of this patent right has assured the ISO that he is willing to negotiat

24、e licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with the ISO. Information may be obtained from: Perten Instruments AB P.O. Box 5101 S-141 05 HUDDINGE Sweden A

25、ttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3093 was prepared by Technical Committee ISO/TC 34, Food product

26、s, Subcommittee SC 4, Cereals and pulses. This fourth edition cancels and replaces the third edition (ISO 3093:2004), of which it constitutes a minor revision. It also incorporates the Technical Corrigendum, ISO 3093:2004/Cor.1:2008. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010

27、06:53, Uncontrolled Copy, (c) BSIBS EN ISO 3093:2009INTERNATIONAL STANDARD ISO 3093:2009(E) ISO 2009 All rights reserved 1Wheat, rye and their flours, durum wheat and durum wheat semolina Determination of the falling number according to Hagberg-Perten 1 Scope This International Standard specifies th

28、e determination of the a-amylase activity of cereals by the falling number (FN) method according to Hagberg-Perten. This method is applicable to cereal grains, in particular to wheat and rye and their flours, durum wheat and its semolina. This method is not applicable to the determination of low lev

29、els of a-amylase activity. By converting the FN into a liquefaction number (LN), it is possible to use this method to estimate the composition of mixtures of grain, flour or semolina with known FNs necessary to produce a sample of a required FN. 2 Normative references The following referenced docume

30、nts are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 712, Cereals and cereal products Determination of moisture content Reference

31、 method ISO 3696, Water for analytical laboratory use Specification and test methods 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 falling number FN t total time required to activate a viscometer stirrer and allow it to fall a predetermined

32、 distance through an aqueous gel prepared from heating a mixture of flour or semolina, and water in a viscometer tube, and which is undergoing liquefaction due to attack by the enzyme a-amylase NOTE 1 Time is counted from immersion in the water bath. NOTE 2 The falling number is expressed in seconds

33、. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:53, Uncontrolled Copy, (c) BSIBS EN ISO 3093:2009ISO 3093:2009(E) 2 ISO 2009 All rights reserved3.2 liquefaction number LN nLresult of a simple calculation to convert the falling number (3.1) into a value used to estimate the com

34、position of mixtures of grain, flour or semolina necessary to produce a sample of the required falling number NOTE LNs, unlike FNs, are additive. 4 Principle The a-amylase activity is estimated using the starch present in the sample as a substrate. The determination is based on the ability of an aqu

35、eous suspension of flour, semolina or wholemeal cereal product to gelatinize rapidly in a boiling water bath, and on the measurement of starch liquefaction by the a-amylase present in the sample. Liquefaction affects the thickness of the starch gel and, hence, the resistance to the viscometer stirre

36、r and the time taken for it to fall a defined distance. 5 Reagents 5.1 Water, produced by distillation or demineralization, complying with ISO 3696, grade 3. 6 Apparatus Usual laboratory apparatus and, in particular, the following. 6.1 Apparatus for FN determination1), comprising the following compo

37、nents. 6.1.1 Water bath, with integral heating unit, cooling system and water level indicator. 6.1.2 Electronic timer. 6.1.3 Viscometer stirrer, metallic, able to move freely within the ebonite stopper. Its rods shall be straight and the wheels free from distortion and wear. 6.1.4 Precision viscomet

38、er tubes, manufactured from special glass, with the following dimensions: inner diameter: 21,00 mm 0,02 mm; outer diameter: 23,80 mm 0,25 mm; inner height: 220,0 mm 0,3 mm. 6.1.5 Rubber stoppers, to fit the viscometer tubes. 6.2 Automatic dispenser or pipette, ISO 8655-24, allowing a volume of 25,0

39、ml 0,2 ml to be delivered. 1) The “Falling Number” apparatus having a specifically designed viscometer stirrer produced by Perten Instruments is an example of a suitable device available commercially. This device forms the subject of a patent. This information is given for the convenience of users o

40、f this International Standard and does not constitute an endorsement by ISO of this product. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:53, Uncontrolled Copy, (c) BSIBS EN ISO 3093:2009ISO 3093:2009(E) ISO 2009 All rights reserved 36.3 Analytical balance, capable of being r

41、ead to the nearest 0,01 g. 6.4 Laboratory mill2), hammer type, and fitted with a 0,8 mm screen allowing the production of a wholemeal product meeting the particle size specification shown in 8.1.3. Check the performance of the mill periodically using a well-mixed sample of ground grain (as produced

42、in 8.1.2). The mill may be equipped with an automatic feeding device, particularly for the grinding of high moisture content grain. 6.5 Laboratory sieve, of nominal size of openings 800 m, ISO 5651and ISO 3310 (all parts)2. 7 Sampling Sampling is not part of the method specified in this Internationa

43、l Standard. A recommended sampling method is given in ISO 136905. A representative sample should have been sent to the laboratory. It should not have been damaged or changed during transport or storage. Storage time and storage conditions of the sample in the laboratory may have a significant effect

44、 on FNs. 8 Preparation of test sample 8.1 Whole grain 8.1.1 Elimination of impurities If necessary, clean the sample to eliminate impurities (e.g. stones, dust, husks and other cereal grains). Take a representative 300 g test sample from the laboratory sample. A smaller test sample of about 200 g, a

45、lthough it provides less reproducible results, may be used for routine inspections. If the sample is less than 200 g, the results risk being marred by errors. 8.1.2 Grinding of grain samples Feed the laboratory mill (6.4) carefully with grain to avoid heating and overloading. The feed to the mill ma

46、y be controlled automatically with an automatic feeding device. Grinding should be continued for 30 s to 40 s after the last of the sample has entered the mill. Discard the bran particles remaining inside the mill, provided these do not represent more than 1 % of the quantity of grain sampled for gr

47、inding. Thoroughly mix all of the milled product before use. It is recommended (especially in the case of successive grindings) to allow the meal to cool for 1 h before proceeding with the test. 8.1.3 Ground sample specification WARNING FNs can be affected by the particle size of the ground grain. 2

48、) LM 3100 and LM 120 mills are examples of suitable devices available commercially. This information is given for the convenience of users of this International Standard and does not constitute an endorsement by ISO of these products. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010

49、 06:53, Uncontrolled Copy, (c) BSIBS EN ISO 3093:2009ISO 3093:2009(E) 4 ISO 2009 All rights reservedThe milled product shall comply with the specification given in Table 1. Table 1 Ground sample specification Nominal size of openings of sieve Amount of ground sample passing through sieve m % 710 100 500 95 to 100 200 80 or less Check the particle size distribution of the ground material regularly using a well-mixed sample of ground grain (8.1.2). To do this, select the appropriate sieves, as specified in Table 1, and a