BS EN ISO 2085-2010 Anodizing of aluminium and its alloys Check for continuity of thin anodic oxidation coatings Copper sulfate test《铝和铝合金的阳极氧化 稀薄阳极氧化涂层连续性处理 硫酸铜试验》.pdf

《BS EN ISO 2085-2010 Anodizing of aluminium and its alloys Check for continuity of thin anodic oxidation coatings Copper sulfate test《铝和铝合金的阳极氧化 稀薄阳极氧化涂层连续性处理 硫酸铜试验》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 2085-2010 Anodizing of aluminium and its alloys Check for continuity of thin anodic oxidation coatings Copper sulfate test《铝和铝合金的阳极氧化 稀薄阳极氧化涂层连续性处理 硫酸铜试验》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 2085:2010Anodizing of aluminium and itsalloys Check for continuityof thin anodic oxidationcoatings Copper sulfate test(ISO 2085:2010)BS EN ISO 2085:2010 BRITISH STANDAR

2、DNational forewordThis British Standard is the UK implementation of EN ISO 2085:2010.The UK participation in its preparation was entrusted to TechnicalCommittee STI/32, Anodic oxidation coatings on aluminium.A list of organizations represented on this committee can beobtained on request to its secre

3、tary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 65992 8ICS 25.220.20; 77.120.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard w

4、as published under the authority of theStandards Policy and Strategy Committee on 30 September 2010.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 2085 August 2010 ICS 25.220.20 Supersedes EN 12373-16:2001English Version Anodizing of alu

5、minium and its alloys - Check for continuity of thin anodic oxidation coatings - Copper sulfate test (ISO 2085:2010) Anodisation de laluminium et de ses alliages - Contrle de la continuit des couches anodiques minces - Essai au sulfate de cuivre (ISO 2085:2010) Anodisieren von Aluminium und Aluminiu

6、mlegierungen - Prfung der Kontinuitt dnner anodisch erzeugter Oxidschichten - Kupfersulfatversuch (ISO 2085:2010) This European Standard was approved by CEN on 28 July 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europ

7、ean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (Englis

8、h, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,

9、Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STAND

10、ARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2085:2010: EBS EN ISO 2085:2010EN ISO 2085:2010

11、(E) 3 Foreword This document (EN ISO 2085:2010) has been prepared by Technical Committee ISO/TC 79 “Light metals and their alloys“ in collaboration with Technical Committee CEN/TC 132 “Aluminium and aluminium alloys” the secretariat of which is held by AFNOR. This European Standard shall be given th

12、e status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2011, and conflicting national standards shall be withdrawn at the latest by February 2011. Attention is drawn to the possibility that some of the elements of this document may be

13、 the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12373-16:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to im

14、plement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

15、Switzerland and the United Kingdom. Endorsement notice The text of ISO 2085:2010 has been approved by CEN as a EN ISO 2085:2010 without any modification. BS EN ISO 2085:2010ISO 2085:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwi

16、de federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on tha

17、t committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in a

18、ccordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard re

19、quires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2085 was prepared by Techni

20、cal Committee ISO/TC 79, Light metals and their alloys, Subcommittee SC 2, Organic and anodic oxidation coatings on aluminium. This second edition cancels and replaces the first edition (ISO 2085:1976), which has been technically revised. BS EN ISO 2085:2010BS EN ISO 2085:2010INTERNATIONAL STANDARD

21、ISO 2085:2010(E) ISO 2010 All rights reserved 1Anodizing of aluminium and its alloys Check for continuity of thin anodic oxidation coatings Copper sulfate test 1 Scope This International Standard specifies a method for checking the continuity of thin anodic oxidation coatings on aluminium and its al

22、loys by a copper sulfate contact test. The use of this method is limited to anodic oxidation coatings of thickness less than 5 m, or coatings that have been deformed. NOTE The method described enables a rapid check to be made for the continuity of a thin coating of aluminium oxidation on aluminium a

23、nd its alloys. In cases of doubt regarding a visible fault on the surface of a coating, the use of this method makes it possible to verify whether the fault corresponds to a local gap in the coating which exposes bare metal. 2 Principle Drops of copper sulfate reagent are placed on surface areas of

24、about 100 mm2, chosen at will on the test pieces, avoiding the anodizing contact areas. If the area includes points where the metal is either bare or poorly covered, chemical deposition of copper takes place on the aluminium, accompanied by a release of gas. The drops of applied reagent can be exami

25、ned immediately upon application, either with the naked eye or with a magnifying glass, for the release of gas from points where the metal is bare, which is almost instantaneous. After the test, black and/or dark reddish spots can be seen where the coating is not continuous. 3 Reagents 3.1 Copper su

26、lfate solution, prepared as follows: copper(II) sulfate pentahydrate, (CuSO45H2O): 20 g; hydrochloric acid (20= 1,18 g/ml): 20 ml; distilled water or deionized water: make up to 1 000 ml. 4 Procedure Carry out the test at room temperature. Remove all grease from the test piece. Mark out a test area

27、of approximately 100 mm2on a horizontal part of the test piece, using a wax crayon or a rapidly drying lacquer to delineate the test area, leaving the test area itself unmasked. Cover the test area with the reagent (3.1), using approximately four drops. Leave the reagent in contact with the surface

28、for 5 min, noting any release of gas, then rinse the area with clean water. Examine the surface and count the number of black and/or dark reddish spots per 100 mm2. BS EN ISO 2085:2010ISO 2085:2010(E) 2 ISO 2010 All rights reservedNOTE For a more quantitative measurement, the average diameter of the

29、 black and/or dark reddish spots can also be estimated. 5 Expression of results Record the number of black and/or dark reddish spots per 100 mm2for each area examined and, if appropriate, their average diameter. 6 Test report The test report shall include at least the following information: a) a ref

30、erence to this International Standard (ISO 2085:2010); b) the type and identification of the product tested; c) the results of the test (see Clause 5); d) anything unusual noticed during the determination; e) the date of the test. BS EN ISO 2085:2010This page deliberately left blankThis page deliber

31、ately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Ins

32、titution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the

33、constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover

34、.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy v

35、ersions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international st

36、andards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 89

37、96 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substan

38、tial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information ab

39、out BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored

40、in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: