BS EN 62055-31-2005 Electricity metering - Payments systems - Part 31 Particular requirements - Static payment meters for active energy (classes 1 and 2)《电表 付费系统 第31部分 特殊要求 电度表用固定付.pdf

《BS EN 62055-31-2005 Electricity metering - Payments systems - Part 31 Particular requirements - Static payment meters for active energy (classes 1 and 2)《电表 付费系统 第31部分 特殊要求 电度表用固定付.pdf》由会员分享，可在线阅读，更多相关《BS EN 62055-31-2005 Electricity metering - Payments systems - Part 31 Particular requirements - Static payment meters for active energy (classes 1 and 2)《电表 付费系统 第31部分 特殊要求 电度表用固定付.pdf（66页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 62055-31:2005Electricity metering Payment systems Part 31: Particular requirements Static payment meters for active energy (classes 1 and 2)The European Standard EN 62055-31:2005 has the status of a British StandardICS 91.140.50g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g

2、55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Tue Apr 25 02:01:05 BST 2006, Uncontrolled Copy, (c) BSIBS EN 62055-31:2005This British Standard was published under the

3、authority of the Standards Policy and Strategy Committee on 30 January 2006 BSI 30 January 2006ISBN 0 580 47583 2National forewordThis British Standard is the official English language version of EN 62055-31:2005. It is identical with IEC 62055-31:2005.The UK participation in its preparation was ent

4、rusted to Technical Committee PEL/13, Electricity meters, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in thi

5、s document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a cont

6、ract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals f

7、or change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 63 and a back cover.The BSI copyright notice displayed in this

8、document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Tue Apr 25 02:01:05 BST 2006, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD EN 62055-31 NORME EUROPENNE EUROPISCHE NORM December 2005 CENELEC European Committee fo

9、r Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members

10、. Ref. No. EN 62055-31:2005 E ICS 91.140.50 English version Electricity metering Payment systems Part 31: Particular requirements Static payment meters for active energy (classes 1 and 2) (IEC 62055-31:2005) Equipements de comptage de llectricit -Systmes paiement Partie 31: Prescriptions particulire

11、s - Compteurs statiques paiement dnergie active (classes 1 et 2) (CEI 62055-31:2005) Messung der elektrischen Energie - Zhlersysteme mit Inkassofunktion Teil 31: Besondere Anforderungen - Elektronische Inkasso-Wirkverbrauchszhler (Klassen 1 und 2) (IEC 62055-31:2005) This European Standard was appro

12、ved by CENELEC on 2005-11-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such natio

13、nal standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language

14、 and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu

15、xembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, na, Tue Apr 25 02:01:05 BST 2006, Uncontrolled Copy, (c) BSI2 Foreword The text of document 13/1344/FDIS, future edition 1 of IEC 62055-31, prepared by

16、IEC TC 13, Equipment for electrical energy measurement and load control, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62055-31 on 2005-11-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an i

17、dentical national standard or by endorsement (dop) 2006-08-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2008-11-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 62055-31:2005 was approved by CE

18、NELEC as a European Standard without any modification. _ EN 62055-31:2005 Licensed Copy: Wang Bin, na, Tue Apr 25 02:01:05 BST 2006, Uncontrolled Copy, (c) BSI 3 EN 62055-31:2005 CONTENTS INTRODUCTION.5 1 Scope 6 2 Normative references .7 3 Terms and definitions .7 3.1 General payment metering defin

19、itions 7 3.2 Definitions of tokens 9 3.3 Definitions of token carriers .10 3.4 Definitions relating to tokens and token carriers .12 3.5 Definitions related to load switching .13 3.6 Definitions related to timekeeping and tariff control 14 4 Standard electrical values.15 5 Mechanical requirements 15

20、 5.1 General .15 5.2 General mechanical requirements 15 5.3 Case .15 5.4 Window .15 5.5 Terminals 16 5.6 Terminal covers.16 5.7 Creepage and clearance distances 16 5.8 Insulating-encased meter of protective class II .16 5.9 Resistance to heat and fire 16 5.10 Protection against penetration of dust a

21、nd water 16 5.11 Display and indicators16 5.12 Output device 18 5.13 Marking of meter .18 5.14 Token carrier interface.18 6 Climatic requirements.18 6.1 General .18 6.2 Temperature range 19 7 Electrical requirements .20 7.1 General .20 7.2 Influence of supply voltage 21 7.3 Power consumption .23 7.4

22、 Influence of short-time overcurrents .23 7.5 Influence of heating .24 7.6 Influence of self-heating.24 7.7 Insulation 24 7.8 Electromagnetic compatibility (EMC) 24 7.9 Load switching 26 7.10 Auxiliary output switches .28 7.11 Token carrier acceptor interface test 28 8 Metering accuracy requirements

23、 .28 Licensed Copy: Wang Bin, na, Tue Apr 25 02:01:05 BST 2006, Uncontrolled Copy, (c) BSIEN 62055-31:2005 4 9 Functional requirements .28 9.1 General .28 9.2 Robustness of meter accounting process .29 10 Type test30 Annex A (informative) Functional performance31 A.1 Basic functionalities prepayment

24、 mode31 A.2 Additional functionalities 38 A.3 System compliance requirements .40 Annex B (informative) Reference model for a payment meter 41 B.1 General .41 B.2 Generalised payment meter instance42 B.3 Functions in a single-part payment meter .44 Annex C (normative) Performance requirements for pay

25、ment meters with load switching utilisation categories UC2, UC3 and UC4 .48 C.1 Load switching capabilities.48 C.2 Normal operation .48 C.3 Electrical endurance 49 C.4 Line to load voltage surge withstand.50 C.5 Fault current making capacity.51 C.6 Short-circuit current carrying capacity 52 C.7 Mini

26、mum switched current54 C.8 Dielectric strength54 C.9 Sequence of tests 55 Annex D (normative) Requirements of timekeeping.56 D.1 General .56 D.2 Synchronous clocks .57 D.3 Crystal-controlled clocks 57 D.4 Tests of timekeeping accuracy .58 D.5 Effects of disturbances on timekeeping.59 Annex ZA (norma

27、tive) Normative references to international publications with their corresponding European publications .62 Table C.1 Summary of test currents for UC2, UC3 and UC448 Table C.2 Test sequence and sample plan .55 Licensed Copy: Wang Bin, na, Tue Apr 25 02:01:05 BST 2006, Uncontrolled Copy, (c) BSI 5 EN

28、 62055-31:2005 INTRODUCTION Payment meters are used in situations where the supply of electrical energy to the load may be interrupted or its restoration enabled under the control of the payment meter in relation to a payment tariff agreed between the customer and the supplier. The payment meter is

29、part of a system that uses token carriers to pass payment information as tokens between a vending network and the payment meters that include the meter accounting process. The functions of a payment meter are to measure electrical energy consumed and to decrement the available credit value in accord

30、ance with the metered consumption, and possibly in accordance with the passing of time. This available credit value is incremented as the result of payments made to the electricity supplier, and the meter accounting process continuously calculates the balance of available credit held by the customer

31、. When the available credit value has been decremented to a predetermined value that is related to the payment mode in use, a switch is used to interrupt the supply to the customers load. However, additional features may be present in the payment meter, which prevent or delay the opening of the swit

32、ch, or limit further consumption to a low load level. Such “social” features may include the provision of an emergency credit facility, the possibility of operation in a fixed-payment mode, and the inhibiting of interruptions for certain periods of time. In return for the payment (usually in cash) a

33、nd depending on the particular type of system, the customer may be issued with a single-use token on a disposable token carrier for the equivalent value, or a reusable token carrier may be credited with that value, or the token may be transmitted directly to the meter via a communications network (a

34、 so-called virtual token carrier). “One-way” and “two-way” data transfer systems may be used, and the token carriers may be: physical devices such as smart cards, or other electronic devices, or magnetic cards; virtual token carriers where the token information is transferred by a remote communicati

35、ons system; or numeric token carriers where sequences of digits are issued on a paper receipt and entered via a keypad on the meter. IEC 62051 provides some details of payment metering terminology in Clause 17. Licensed Copy: Wang Bin, na, Tue Apr 25 02:01:05 BST 2006, Uncontrolled Copy, (c) BSIEN 6

36、2055-31:2005 6 ELECTRICITY METERING PAYMENT SYSTEMS Part 31: Particular requirements Static payment meters for active energy (classes 1 and 2) 1 Scope This part of IEC 62055 applies to newly manufactured, static watt-hour payment meters of accuracy classes 1 and 2 for direct connection, for the meas

37、urement of alternating current electrical energy consumption of a frequency in the range 45 Hz to 65 Hz that include a load switch for the purpose of interruption or restoration of the electricity supply to the load in accordance with the current value of the available credit maintained in the payme

38、nt meter. It does not apply to static watt-hour payment meters where the voltage across the connection terminals exceeds 600 V (line-to-line voltage for meters for polyphase systems). It applies to payment meters for indoor application only, where the payment meter shall be mounted as for normal ser

39、vice (i.e. together with a specified matching socket where applicable). Payment meters are implementations where all the main functional elements are incorporated in a single enclosure, together with any specified matching socket. There are also multi-part installations where the various main functi

40、onal elements, such as the measuring element, the user interface unit, token carrier interface, and the load switch are implemented in more than one enclosure, involving additional interfaces. This part of IEC 62055 does not apply to multi-part payment metering installations. Functional requirements

41、 that apply to payment meters are also defined in this part of IEC 62055, and include informative basic functional requirements and tests for the prepayment mode of operation in Annex A. Allowances are made for the relatively wide range of features, options, alternatives, and implementations that ma

42、y be found in practice. The diverse nature and functionality of payment meters prevent the comprehensive specification of detailed test methods for all of these requirements. However, in this case, the requirements are stated in such a way that tests can then be formulated to respect and validate th

43、e specific functionality of the payment meter being tested. This part of IEC 62055 does not cover specific functionality or performance requirements for safety, circuit protection, isolation or similar purposes that may be specified through reference to other specifications or standards. This part o

44、f IEC 62055 does not cover software requirements. Software requirements for basic energy meter metrology are under consideration for the IEC 62059 series of standards, and in other organisations. This part of IEC 62055 covers type-testing requirements only. For acceptance testing, the concepts given

45、 in IEC 61358 may be used as a basic guideline. Dependability aspects are addressed in the IEC 62059 series of standards. This part of IEC 62055 does not cover conformity tests and system compliance tests that may be required in connection with legal or other requirements of some markets. Licensed C

46、opy: Wang Bin, na, Tue Apr 25 02:01:05 BST 2006, Uncontrolled Copy, (c) BSI 7 EN 62055-31:2005 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest ed

47、ition of the referenced document (including any amendments) applies. IEC 62051:1999, Electricity metering Glossary of terms. IEC 61358:1996, Acceptance inspection for direct-connected alternating current static watt-hour meters for active energy (classes 1 and 2) IEC 62052-11:2003, Electricity meter

48、ing equipment (AC) General requirements, tests and test conditions Part 11: Metering equipment IEC 62053-21:2003, Electricity metering equipment (AC) Particular requirements Part 21: Static meters for active energy (classes 1 and 2) IEC 60050-300:2001, International Electrotechnical Vocabulary Elect

49、rical and electronic measurements and measuring instruments Part 311: General terms relating to measurements Part 312: General terms relating to electrical measurements Part 313: Types of electrical measuring instruments Part 314: Specific terms according to the type of instrument IEC 61000-4-5:1995, Electromagnetic compatibility (EMC) Part 4-5: Testing and measurement techniques Surge immunity test IEC 61008-1:1996, Residual current operated circuit-breakers without integral overcu