BS EN 61755-3-31-2015 Fibre optic interconnecting devices and passive components Connector optical interfaces Connector parameters of non-dispersion shifted single mode physically r.pdf

《BS EN 61755-3-31-2015 Fibre optic interconnecting devices and passive components Connector optical interfaces Connector parameters of non-dispersion shifted single mode physically r.pdf》由会员分享，可在线阅读，更多相关《BS EN 61755-3-31-2015 Fibre optic interconnecting devices and passive components Connector optical interfaces Connector parameters of non-dispersion shifted single mode physically r.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationFibre optic interconnecting devices and passive components Connector optical interfacesPart 3-31: Connector parameters of non-dispersion shifted single mode physically contacting fibres Angled polyphenylene sulphide rectangular ferrulesBS EN 61755-3-31:2015National forewordT

2、his British Standard is the UK implementation of EN 61755-3-31:2015. It isidentical to IEC 61755-3-31:2015.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre opticinterconnecting devices and passive components.A list of o

3、rganizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2

4、015ISBN 978 0 580 71627 0ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2015.Amendments/corrigenda issued since publicationDate Text aff

5、ectedBRITISH STANDARDBS EN 61755-3-31:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61755-3-31 September 2015 ICS 33.180.20 English Version Fibre optic interconnecting devices and passive components - Connector optical interfaces - Part 3-31: Connector parameters of non-dispersion shifted

6、 single mode physically contacting fibres - Angled polyphenylene sulphide rectangular ferrules (IEC 61755-3-31:2015) Dispositifs dinterconnexion et composants passifs fibres optiques - Interfaces optiques de connecteurs - Partie 3-31: Paramtres de connecteurs pour fibres unimodales dispersion non dc

7、ale, en contact physique - Frules rectangulaires avec angle en poly(sulfure de phnylne) (IEC 61755-3-31:2015) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Optische Schnittstellen fr Lichtwellenleiter-Steckverbinder - Teil 3-31: Optische Schnittstelle rechteckige Polyphenylensulfid-

8、Ferrule 8 Grad abgewinkelt physikalischer Kontakt fr Einmodenfasern (IEC 61755-3-31:2015) This European Standard was approved by CENELEC on 2015-07-17. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the s

9、tatus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, Fre

10、nch, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria

11、, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,

12、Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of exp

13、loitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61755-3-31:2015 E BS EN 61755-3-31:2015EN 61755-3-31:2015 2 European foreword The text of document 86B/3888/FDIS, future edition 1 of IEC 61755-3-31, prepared by SC 86B “Fibre optic interconnecting devices and

14、 passive components“ of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61755-3-31:2015. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or

15、by endorsement (dop) 2016-04-17 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-07-17 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held r

16、esponsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61755-3-31:2015 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the sta

17、ndards indicated: IEC 61753-1 NOTE Harmonized as EN 61753-1. IEC 61755-2-1 NOTE Harmonized as EN 61755-2-1. BS EN 61755-3-31:2015EN 61755-3-31:2015 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in who

18、le or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publicati

19、on has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 60793-2-50 - Optical fibres - Part

20、 2-50: Product specifications - Sectional specification for class B single-mode fibres EN 60793-2-50 - IEC 61300-3-30 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-30: Examinations and measurements - Polish angle and fibre position on s

21、ingle ferrule multifibre connectors EN 61300-3-30 - IEC 61300-3-52 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-52: Examinations and measurements - Guide hole and alignment pin deformation constant, CD for 8 degree angled PC rectangula

22、r ferrule, single mode fibres EN 61300-3-52 - IEC 61754 Series Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces EN 61754 Series IEC 61754-5 2005 Fibre optic connector interfaces - Part 5: Type MT connector family EN 61754-5 2005 IEC 61754-7 2008 Fibre opt

23、ic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7: Type MPO connector family EN 61754-7 2008 IEC 61754-7-1 2014 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7-1: Type MPO connector family - One fibre

24、row EN 61754-7-1 2014 IEC 61754-10 2005 Fibre optic connector interfaces - Part 10: Type Mini-MPO connector family EN 61754-10 2005 IEC 61754-18 2001 Fibre optic connector interfaces - Part 18: Type MT-RJ connector family EN 61754-18 + corr. April 2002 2002 IEC 61755-1 - Fibre optic connector optica

25、l interfaces - Part 1: Optical interfaces for single mode non-dispersion shifted fibres - General and guidance EN 61755-1 - BS EN 61755-3-31:2015 2 IEC 61755-3-31:2015 IEC 2015 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Description 6 4 Interface parameters . 6 Annex A (informative) T

26、heoretical worst-case connector attenuation yield percentage . 16 Annex B (normative) Minus coplanarity 19 Annex C (informative) Minimum normal force required to achieve physical contact 20 Bibliography 25 Figure 1 Fibre numbering conventions . 7 Figure 2 Interface dimensions related to lateral and

27、angular offset . 8 Figure 3 Alignment pin geometry 8 Figure 4 Interface dimensions related to longitudinal offset 9 Figure A.1 Monte Carlo simulation of Grade B performance for 12-fibre connectors . 16 Figure B.1 Illustration of fibre line and minus coplanarity parameters . 19 Figure C.1 Geometry li

28、mit, GL, needed to mate 12 fibres, as a function of absolute X-angle, SX for different magnitudes of minus coplanarity and flat fibre tips 21 Figure C.2 Geometry limit, GL, needed to mate 12 fibres, as a function of absolute X-angle, SX for different magnitudes of minus coplanarity and 1 mm fibre ti

29、ps. . 21 Table 1 Optical interface variant information 7 Table 2 Optical interface dimensions related to lateral and angular offset for optical interface variant 1002 . 10 Table 3 Optical interface dimensions related to lateral and angular offset for optical interface variants 1104, 1108, 1112 11 Ta

30、ble 4 Optical interface end face geometry dimensions related to physical contact for optical interface variant 1002 . 12 Table 5 Optical interface end face geometry dimensions related to physical contact for optical interface variant 1104 . 13 Table 6 Optical interface end face geometry dimensions r

31、elated to physical contact for optical interface variant 1108 . 14 Table 7 Optical interface end face geometry dimensions related to physical contact for optical interface variant 1112 . 15 Table A.1 Grade B single channel vs. multi-fibre connector performance . 17 Table A.2 Grade C single channel v

32、s. multi-fibre connector performance . 17 Table A.3 Grade D single channel vs. multi-fibre connector performance . 17 Table C.1 Parameter constants for 4-fibre optical interface variant 1104 23 Table C.2 Parameter constants for 8-fibre optical interface variant 1108 24 Table C.3 Parameter constants

33、for 12-fibre optical interface variant 1112 24 BS EN 61755-3-31:2015IEC 61755-3-31:2015 IEC 2015 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS CONNECTOR OPTICAL INTERFACES Part 3-31: Connector parameters of non-dispersion shifted single mode

34、 physically contacting fibres Angled polyphenylene sulphide rectangular ferrules FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to prom

35、ote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides

36、(hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also

37、 participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possib

38、le, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. Whil

39、e all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake t

40、o apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestatio

41、n of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of thi

42、s publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or ind

43、irect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for t

44、he correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61755-3-31 has been

45、prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. The text of this standard is based on the following documents: FDIS Report on voting 86B/3888FDIS 86B/3914/RVD Full information on the voting for the approval of thi

46、s standard can be found in the report on voting indicated in the above table. BS EN 61755-3-31:2015 4 IEC 61755-3-31:2015 IEC 2015 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 61755 series, published under the general title Fibre

47、 optic interconnecting devices and passive components Connector optical interfaces, can be found on the IEC website. Future standards in this series will carry the new general title as cited above. Titles of existing standards in this series will be updated at the time of the next edition. The commi

48、ttee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised editi

49、on, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. BS EN 61755-3-31:2015IEC 61755-3-31:2015 IEC 2015 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS CONNECTOR OPTICAL INTERFACES Part 3-31: Connector parameters of n