BS EN 61753-092-6-2007 Fibre optic interconnecting devices and passive components performance standard - Non-connectorized single-mode circulators for category O Uncontrolled envir.pdf

《BS EN 61753-092-6-2007 Fibre optic interconnecting devices and passive components performance standard - Non-connectorized single-mode circulators for category O Uncontrolled envir.pdf》由会员分享，可在线阅读，更多相关《BS EN 61753-092-6-2007 Fibre optic interconnecting devices and passive components performance standard - Non-connectorized single-mode circulators for category O Uncontrolled envir.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 61753-092-6: 2007Fibre optic interconnecting devices and passive components performance standard Part 092-6: Non-connectorized single-mode circulators for category O Uncontrolled environment and sequential testThe European Standard EN 61753-092-6:2007 has the status of a Britis

2、h StandardICS 33.180.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 61753-092-6:2007This British Standard was published under the authority

3、 of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2007ISBN 978 0 580 53584 0National forewordThis British Standard is the UK implementation of EN 61753-092-6:2007. It is identical to IEC 61753-092-6:2007.The UK participation in its preparation was entrusted by Technical Committ

4、ee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnecting devices and passive components.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Use

5、rs are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD EN 61753-092-6 NORME EUROPENNE EUROPISCHE NORM October 2007 CENELEC European Committee for Electr

6、otechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. N

7、o. EN 61753-092-6:2007 E ICS 33.180.20 English version Fibre optic interconnecting devices and passive components performance standard - Part 092-6: Non-connectorized single-mode circulators for category O - Uncontrolled environment and sequential test (IEC 61753-092-6:2007) Norme de qualit de fonct

8、ionnement des dispositifs dinterconnexion et composants passifs fibres optiques - Partie 092-6: Circulateurs unimodaux non connectoriss pour la catgorie O - Environnement non contrl et essai squentiel (CEI 61753-092-6:2007) Lichtwellenleiter -Verbindungselemente und passive Bauteile - Betriebsverhal

9、ten - Teil 092-6: Nicht mit Steckern versehene Einmoden-LWL-Zirkulatoren der Kategorie O - Freiluftanlagen und Prffolge (IEC 61753-092-6:2007) This European Standard was approved by CENELEC on 2007-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate t

10、he conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exis

11、ts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national elect

12、rotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer

13、land and the United Kingdom. Foreword The text of document 86B/2530/FDIS, future edition 1 of IEC 61753-092-6, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN

14、61753-092-6 on 2007-10-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2008-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn

15、(dow) 2010-10-01 Annex ZA has been added by CENELEC. _ Notice This document contains material that is Copyright 2006, Telcordia Technologies, Inc. (“Telcordia“). All rights reserved. The reader is advised that this IEC document and Telcordia source(s) may differ, and the context and use of said mate

16、rial in this IEC document may differ from that of Telcordia. Telcordia makes no representation or warranty, express or implied, with respect to the sufficiency, accuracy, or utility of any information or opinion contained herein. Any use of or reliance upon said information or opinion is at the risk

17、 of the user. Telcordia shall not be liable for any damage or injury incurred by any person arising out of the sufficiency, accuracy, or utility of any information or opinion contained herein. _ Endorsement notice The text of the International Standard IEC 61753-092-6:2007 was approved by CENELEC as

18、 a European Standard without any modification. _ EN 61753-092-6:2007 2 3 EN 61753-092-6:2007 CONTENTS 1 Scope 5 2 Normative references .5 3 Test .6 4 Test report .7 5 Performance requirements .7 5.1 Sample size, sequencing and grouping 7 5.2 Test details and requirements7 Annex A (normative) Sequenc

19、ing and grouping of tests13 Annex ZA (normative) Normative references to international publications with their corresponding European publications .15 Bibliography .14 Table 1 Single-mode spectral bands 7 Table 2 Test details and requirements8 EN 61753-092-6:2007 4 NOTICE This document contains mate

20、rial that is Copyright 2006, Telcordia Technologies, Inc. (“Telcordia“). All rights reserved. The reader is advised that this IEC document and Telcordia source(s) may differ, and the context and use of said material in this IEC document may differ from that of Telcordia. TELCORDIA MAKES NO REPRESENT

21、ATION OR WARRANTY, EXPRESS OR IMPLIED, WITH RESPECT TO THE SUFFICIENCY, ACCURACY, OR UTILITY OF ANY INFORMATION OR OPINION CONTAINED HEREIN. ANY USE OF OR RELIANCE UPON SAID INFORMATION OR OPINION IS AT THE RISK OF THE USER. TELCORDIA SHALL NOT BE LIABLE FOR ANY DAMAGE OR INJURY INCURRED BY ANY PERS

22、ON ARISING OUT OF THE SUFFICIENCY, ACCURACY, OR UTILITY OF ANY INFORMATION OR OPINION CONTAINED HEREIN. 5 EN 61753-092-6:2007 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS PERFORMANCE STANDARD Part 092-6: Non-connectorized single-mode circulators for category O Uncontrolled environment

23、and sequential test 1 Scope This part of IEC 61753 contains the minimum test and measurement requirements and severities which a fibre optic circulator should satisfy in order to be categorized as meeting the requirements of circulator devices used in outside plant environments. The requirements cov

24、er non-connectorized single-mode circulators for caterogy O used in an uncontrolled environment and a sequential test. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated r

25、eferences, the latest edition of the referenced document (including any amendments) applies. IEC 60793-1-1, Optical fibres Part 1-1: Measurement methods and test procedures General and guidance IEC 61300-2-1, Fibre optic interconnecting devices and passive components Basic test and measurement proce

26、dures Part 2-1: Tests Vibration (sinusoidal) IEC 61300-2-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-4: Tests Fibre/cable retention IEC 61300-2-5, Fibre optic interconnecting devices and passive components Basic test and measurement proc

27、edures Part 2-5: Tests Torsion/twist IEC 61300-2-9, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-9: Tests Shock IEC 61300-2-14, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-14: Tests

28、 Optical power handling and damage threshold characterization IEC 61300-2-19, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-19: Tests Damp heat (steady state) IEC 61300-2-22, Fibre optic interconnecting devices and passive components Basic te

29、st and measurement procedures Part 2-22: Tests Change of temperature EN 61753-092-6:2007 6 IEC 61300-2-42, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-42: Tests Static side load for connectors IEC 61300-2-44, Fibre optic interconnecting dev

30、ices and passive components Basic test and measurement procedures Part 2-44: Tests Flexing of the strain relief of fibre optic devices IEC 61300-2-48, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-48: Tests Temperature-humidity cycling IEC 61

31、300-3-2, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-2: Examinations and measurements Polarization dependence of attenuation in a single-mode fibre optic device IEC 61300-3-7, Fibre optic interconnecting devices and passive components Basic

32、 test and measurement procedures Part 3-7: Examinations and measurements Wavelength dependence of attenuation and return loss IEC 61300-3-32, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-32: Examinations and measurements Polarisation mode di

33、spersion measurement for passive optical components3 Test All test methods are in accordance with a particular IEC 61300 standard, of which parts applicable to this standard are mentioned in 5.2 (see Table 2). The samples shall be terminated onto single-mode fibres as per IEC 60793-1-1 Type B 1.1 in

34、 either coated fibres (primary and secondary) or reinforced cable format. Each test defines the number of samples to be evaluated. The Table 1 is intended to provide guidance on the wavelength ranges of the various spectral bands. It is not intended for specification. Values of operating wavelength

35、used in performance verification shall be specified between the customer and supplier or shall be as defined in the manufacturers specification. 7 EN 61753-092-6:2007 Table 1 Single-mode spectral bands Band Descriptor Range nm O-band Original 1 260 to 1 360 E-band Extended 1 360 to 1 460 S-band Shor

36、t wavelength 1 460 to 1 530 C-band Conventional 1 530 to 1 565 L-band Long wavelength 1 565 to 1 625 U-band Ultralong wavelength 1 625 to 1 675 Source: ITU-T Supplement 39. 4 Test report Fully documented test reports and supporting evidence shall be prepared and be available for inspections as evide

37、nce that the tests have been carried out and complied with. 5 Performance requirements 5.1 Sample size, sequencing and grouping Sample sizes for the tests are defined in Annex A of this standard. Test groups and test sequences shall be performed in sequential order as shown in Annex A. 5.2 Test deta

38、ils and requirements Attenuation and return loss performances are given only for non-connectorised circulators. For connectorised components the connector performances should be in compliance with IEC 61753-021-6. During the environmental tests where monitoring of the circulator performance is speci

39、fied, the ports of the device shall be controlled. EN 61753-092-6:2007 8 Table 2 Test details and requirements No Tests Requirements Details 1 Attenuation 1,0 dB (standard isolation type) 1,2 dB (high isolation type) Attenuation shall be met over the following operating wavelength range. Operating w

40、avelength range for C-band: 1 530 nm - 1 565 nm. Operating wavelength range for L-band: 1 565 nm - 1 625 nm. IEC 61300-3-7 Method: Optical power meter.Launch fibre length: 1,5 m The test conditions shall provide attenuation measurement results with an accuracy of 0,05 dB over the wavelength range an

41、d with a spectral resolution defined by the targeted application. Wavelength range: Specified by application. 2 Isolation 12 dB (standard isolation type) 30 dB (high isolation type) Isolation shall be met over the following operating wavelength range. Operating wavelength range for C-band: 1 530 nm

42、- 1 565 nm. Operating wavelength range for L-band: 1 565 nm - 1 625 nm. IEC 61300-3-7 Method: Optical power meter or Optical spectrum analyser. Details: same as in test No. 1. 3 Return loss 35 dB (Class T) 40 dB (Class R) 50 dB (Class U) 60 dB (Class V) Return loss shall be met over the following op

43、erating wavelength range. Operating wavelength range for C-band: 1 530 nm 1 565 nm. Operating wavelength range for L-band: 1 565 nm 1 625 nm IEC 61300-3-7, Method 1 or 2 Ports not under test shall be optically terminated to avoid unwanted reflections contributing to the measurement 4 Polarisation de

44、pendent loss 0,1 dB (standard isolation type) 0,2 dB (high isolation type) PDL shall be met over the following operating wavelength range. Operating wavelength range for C-band: 1 530 nm 1 565 nm. Operating wavelength range for L-band: 1 565 nm -1 625 nm IEC 61300-3-2 9 EN 61753-092-6:2007 Table 2 (

45、continued) No Tests Requirements Details 5 Polarisation mode dispersion 0,1 ps (PMD compensation type) 0,8 ps (PMD non-compensation type) PMD shall be met over operating wavelength range. Operating wavelength range for C-band: 1 530 nm 1 565 nm. Operating wavelength range for L-band: 1 565 nm 1 625

46、nm. IEC61300-3-32 6 Chromatic dispersion 0,1 ps/nm Chromatic dispersion shall be met over operating wavelength range. Operating wavelength range for C-band: 1 530 nm 1 565 nm. Operating wavelength range for L-band: 1 565 nm 1 625 nm. IEC/PAS 61300-3-38 7 Optical power characterization On completion

47、of the test the requirement regarding the maximum allowable attenuation and Isolation shall be met. During and on completion of the test, the attenuation and the isolation shall be within 0,3 dB with respect to the initial value. On completion of the test, the isolation shall be within 2 dB with res

48、pect to the initial value. Return loss shall satisfy the requirements for the specified class. IEC 61300-2-14 Maximum power to supply: 20 dBm Power increment: 5 dB Duration of the optical power exposure: 30 min Other details: same as in tests No.1, 2 and 3Attenuation and isolation shall be measured

49、before, at a maximum interval of 10 min during and after the test. Return loss shall be measured before and after the test. 8 Damp heat (Steady state) On completion of the test the requirement regarding the maximum allowable attenuation and iIsolation shall be met. During and on completion of the test, the attenuation shall be within 0,3 dB with respect to the initial value. Retur