BS EN 61580-7-1997 Methods of measurement for waveguides - Graphical method for the determination of waveguide performance《波导管测量方法 图解法测定波导管性能》.pdf

《BS EN 61580-7-1997 Methods of measurement for waveguides - Graphical method for the determination of waveguide performance《波导管测量方法 图解法测定波导管性能》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61580-7-1997 Methods of measurement for waveguides - Graphical method for the determination of waveguide performance《波导管测量方法 图解法测定波导管性能》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61580-7:1997 IEC 1580-7: 1996 Methods of measurement for waveguides Part 7: Graphical method for the determination of waveguide performance The European Standard EN61580-7:1996 has the status of a British Standard ICS33.120.10BSEN61580-7:1997 This British Standard, having been

2、 prepared under the directionof the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 February1997 BSI 12-1998 The following BSI references relate to the work on this standard: Committee reference EPL/46/2 Draft announced in BSI Updat

3、e October 1996 ISBN 0 580 26939 6 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee EPL/46, Cables, wires and waveguides, RF connectors and accessories for communication and signalling, to Subcommittee EPL/46/2, RFconnector

4、s and waveguides, upon which the following bodies were represented: AEA Technology BEAMA Electrical Cable and Conductor Accessory Manufacturers British Non-Ferrous Metals Federation British Telecommunications plc Federation of the Electronics Industry Ministry of Defence National Supervisory Inspect

5、orate Society of Cable Television Engineers Amendments issued since publication Amd. No. Date CommentsBSEN61580-7:1997 BSI 12-1998 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 61580-7 3BSEN61580-7:1997 ii BSI 12-1998 National foreword This Brit

6、ish Standard has been prepared by Subcommittee EPL/46/2 and is the English language version of EN61580-7:1996 Methods of measurement for waveguides Part7: Graphical method for the determination of waveguide performance published by the European Committee for Electrotechnical Standardization (CENELEC

7、). It is identical with IEC1580-7:1996 published by the International Electrotechnical Commission (IEC). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Stan

8、dard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 8 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated

9、. This will be indicated in the amendment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61580-7 August 1996 ICS33.120.10 Descriptors: Waveguides, graphical method for the determination of performance English version Methods of measurement for waveguides Part 7:

10、Graphical method for the determination of waveguide performance (IEC1580-7:1996) Mthodes de mesure appliques aux guides dondes Partie 7: Mthode graphique pour dterminer les performances dun guide dondes (CEI1580-7:1996) Meverfahren fr Hohlleiter Teil 7: Graphisches Verfahren zur Bestimmung der Hohll

11、eiter-eigenschaften (IEC1580-7:1996) This European Standard was approved by CENELEC on1996-07-02. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. U

12、p-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translatio

13、n under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, It

14、aly, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1

15、050 Brussels 1996 Copyright reserved to CENELEC members Ref. No. EN 61580-7:1996 EEN61580-7:1996 BSI 12-1998 2 Foreword The text of document46B/208/FDIS, future edition1 of IEC1580-7, prepared by SC46B, Waveguides and their accessories, of IEC TC46, Cables, wires, waveguides, R.F. connectors, and ac

16、cessories for communication and signalling, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN61580-7 on1996-07-02. The following dates were fixed: Contents Page Foreword 2 1 Scope 3 2 Form of presentation 3 3 Examples 3 3.1 Ordinary rectangular waveguides 3 3.2 Medium

17、flat rectangular waveguides 3 3.3 Square waveguides 3 3.4 Circular waveguides 3 4 Formulae for cut-off wavelengths 3 4.1 Rectangular waveguides 3 4.2 Circular waveguides 4 Figure 1 5 Figure 2 6 Figure 3 7 Figure 4 8 Table 1 Roots of Bessel function for TE mnmodes 4 Table 2 Roots of Bessel function f

18、or TM mnmodes 4 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1997-04-01 latest date by which the national standards conflicting with the EN haveto be withdrawn (dow) 1997-04-01EN61580-7:1996 BSI 12-1998 3

19、 1 Scope This part of IEC1580 is applicable to waveguide performance. The objective is to provide a means for determining the cut-off frequencies for the dominant and higher order modes in waveguides of various types over the frequency range from1GHz to27GHz. It is only intended to be used as an app

20、endix to the measuring method published by SC46B. 2 Form of presentation 2.1 Information is presented in the form of nomograms (seeFigure 1 toFigure 3) for the following waveguide types: ordinary rectangular waveguide (aspect ratio2 : 1); medium flat rectangular waveguide (aspect ratio3 : 1); square

21、 waveguide; circular waveguide. 2.2 To determine waveguide performance, project a line horizontally corresponding to a specified mode to cut the a/l axis. Draw a line from this point through the “a” (mm) line to cut the frequency axis. 2.3 If greater accuracy is required, the cut-off frequencies can

22、 be calculated using the relationships listed in clause 4 for the cut-off wavelengths (lc). Cut-off frequency is then given by fc = c/lc, where “c” is the velocity of light. 2.4 Examples are given below to illustrate the use of the nomograms. 3 Examples 3.1 Ordinary rectangular waveguides 3.1.1 For

23、ordinary rectangular waveguides the recommended frequency range extends from25% above the dominant mode cut-off to 5% below the cut-off for the next higher order mode. 3.1.2 To determine the normal operating frequency band for, say, R48 waveguide, proceed as follows using the nomogram shown asFigure

24、 2: a) project the TE 10and TE 20lines horizontally to cut the a/l axis at 0,5 and1,0 respectively; b) draw a line from the points0,5 and1,0 through the point a =47,55mm to cut the frequency axis at the points corresponding to the required cut-off frequencies; c) read off the values3,15GHz for the T

25、E 10mode and6,31GHz for the TE 20mode. 3.1.3 The normal operating band for R48 is therefore: (3,15 + 25 %) = 3,94 GHz to (6,31 5 %) =5,99GHz 3.2 Medium flat rectangular waveguides For these waveguides, suppression of the TE 20mode results in a nominal 1,5 : 0,5 =3 : 1 bandwidth compared with2 : 1 fo

26、r ordinary rectangular waveguides. The TE 20mode is an odd mode which can easily be suppressed by filtering. 3.3 Square waveguides To determine the common cut-off frequency for the TE 11and TM 11modes for a square waveguide with a =34mm proceed as follows: a) project the common TE 11 , TM 11line hor

27、izontally to cut the a/l axis at the point A (seeFigure 4); b) draw a line from A through a =34mm to cut the frequency axis at B, corresponding to the cut-off frequency of6,24GHz. 3.4 Circular waveguides To determine the diameter “a” and the cut-off frequency for a circular waveguide operating up to

28、11GHz in the dominant (TE 11 ) mode only, proceed as follows: a) project the TE 11and TM 01lines horizontally to cut the a/l axis at the points C and D respectively (see Figure 4); b) allowing for a safety factor of approximately1%, draw a line from point D to the point corresponding to11,1GHz on th

29、e frequency axis. This cuts the “a” line at E corresponding to a value a =20,7mm; c) draw a line from C through E to cut the frequency axis at the point F, corresponding to the cut-off frequency of8,5GHz. 4 Formulae for cut-off wavelengths 4.1 Rectangular waveguides For the TE mnand TM mnmodes: wher

30、e a = broad dimension of the wave guide; b = narrow dimension of the waveguide. l c 2 ab m 2 b a -n 2 a b - + - =EN61580-7:1996 4 BSI 12-1998 4.2 Circular waveguides where a = diameter of the guide; x mn = roots of a Bessel function. The first14 roots of the appropriate Bessel functions are tabulate

31、d below for the TE mn(Table 1) and TM mn(Table 2) modes. NOTEm and n can be interchanged to give an orthogonal set of modes for square waveguides. Table 1 Roots of Bessel function for TE mnmodes Table 2 Roots of Bessel function for TM mnmodes l c p a x mn - = m n 0 1 2 3 4 5 6 1 3,832 1,841 3,054 4,

32、201 5,317 6,416 7,501 2 7,016 5,331 6,706 8,015 9,282 10,520 11,735 m n 0 1 2 3 4 5 6 1 2,405 3,832 5,136 6,380 7,588 8,771 9,936 2 5,520 7,016 8,417 9,761 11,065 12,339 13,589EN61580-7:1996 BSI 12-1998 5 Figure 1EN61580-7:1996 6 BSI 12-1998 Figure 2EN61580-7:1996 BSI 12-1998 7 Figure 3EN61580-7:199

33、6 8 BSI 12-1998 Figure 49 blankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

34、| | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by

35、 amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Stand

36、ard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest e

37、ditions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those

38、that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services

39、are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details

40、 of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyri

41、ght, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the s

42、tandard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.