BS EN 61534-22-2014 Powertrack systems Particular requirements for powertrack systems intended for onfloor or underfloor installation《动力轨道系统 第22部分 用于地面或地面下安装的动力轨道系统的详细要求》.pdf

《BS EN 61534-22-2014 Powertrack systems Particular requirements for powertrack systems intended for onfloor or underfloor installation《动力轨道系统 第22部分 用于地面或地面下安装的动力轨道系统的详细要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61534-22-2014 Powertrack systems Particular requirements for powertrack systems intended for onfloor or underfloor installation《动力轨道系统 第22部分 用于地面或地面下安装的动力轨道系统的详细要求》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationPowertrack systems Part 22: Particular requirements for powertracksystems intended for on floor or under floorinstallationBS EN 61534-22:2014BS EN 61534-22:2014National forewordThis British Standard is the UK implementation of EN 61534-22:2014. It is identical to IEC 61534-2

2、2:2014. It supersedes BS EN 61534-22:2009, which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PEL/213, Cable management.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to

3、 include all the necessary provisions of a contract. Users are responsible for its correct application.The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 80752 7 ICS 29.060.10; 29.120.20 Compliance with a British Standard cannot confer immunity from legal ob

4、ligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61534-22 August 2014 ICS 29.120.2

5、0; 29.060.10 English Version Powertrack systems - Part 22: Particular requirements for powertrack systems intended for onfloor or underfloor installation (IEC 61534-22:2014) Systmes de conducteurs prfabriqus - Partie 22: Exigences particulires pour les systmes de conducteurs prfabriqus destins au mo

6、ntage sur le sol ou sous le sol (CEI 61534-22:2014) Stromschienensysteme - Teil 22: Besondere Anforderungen fr Stromschienensysteme fr Fubodeninstallationen (IEC 61534-22:2014) This European Standard was approved by CENELEC on 2014-07-24. CENELEC members are bound to comply with the CEN/CENELEC Inte

7、rnal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any

8、 CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the off

9、icial versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,

10、 Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENE

11、LEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61534-22:2014 E - 2 - Foreword The text of document 23A/702/FDIS, future edition 2 of IEC 61534-22, prepared by SC 23A “Ca

12、ble management systems“, of IEC/TC 23 “Electrical accessories“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61534-22:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national

13、standard or by endorsement (dop) 2015-04-24 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-07-24 This document supersedes EN 61534-22:2009. Attention is drawn to the possibility that some of the elements of this document may be the subject o

14、f patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC). Endorsement notice The tex

15、t of the International Standard IEC 61534-22:2014 was approved by CENELEC as a European Standard without any modification. BS EN 61534-22:2014 EN 61534-22:2014 (E)- 3 - Annex ZA (normative) Normative references to international publications with their corresponding European publications The followin

16、g documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an Inte

17、rnational Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 61534-1 + A1 2

18、011 2014 Powertrack systems - Part 1: General requirements EN 61534-1 + A1 2011 2014 BS EN 61534-22:2014 EN 61534-22:2014 (E) 2 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 General requirements 6 5 General notes on tests 6 6 Ratings 6 7 Classification . 6 8 Ma

19、rking and documentation . 7 9 Construction 8 10 Clearances, creepage distances and solid insulation . 9 11 Protection against electric shock . 9 12 Terminals and terminations 9 13 Screws, current-carrying parts and connections . 9 14 Mechanical strength 9 15 Insulation resistance test and dielectric

20、 strength test . 17 16 Normal operation . 17 17 Temperature rise . 17 18 Short-circuit protection and short-circuit withstand strength . 17 19 Resistance to heat . 17 20 Fire hazard 17 21 External influences 18 22 Electromagnetic compatibility 18 Annex AA (informative) Illustrations of underfloor an

21、d onfloor installations. 19 Annex BB (normative) Additional test requirements for PT systems already complying with IEC 61534-22: 2009 . 21 Figure 101 External load test . 10 Figure 102 Traffic load test for flushfloor service units applied to a small surface area 13 Figure 103 Traffic load test for

22、 flushfloor service units applied to a large surface area 15 Figure 104 Test arrangement for fixing apparatus mounting device according to 14.101.6.1 16 Figure AA.1 Illustrations of underfloor installations . 19 Figure AA.2 Example of installation onfloor 20 BS EN 61534-22:2014 61534-22 IEC:2014 3 I

23、NTERNATIONAL ELECTROTECHNICAL COMMISSION _ POWERTRACK SYSTEMS Part 22: Particular requirements for powertrack systems intended for onfloor or underfloor installation FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all nationa

24、l electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical S

25、pecifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. Inte

26、rnational, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The fo

27、rmal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations

28、for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user.

29、 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication sh

30、all be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent cert

31、ification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal in

32、jury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references

33、 cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for ident

34、ifying any or all such patent rights. International Standard IEC 61534-22 has been prepared by subcommittee 23A: Cable management systems, of IEC Technical Committee 23: Electrical accessories. This second edition cancels and replaces the first edition published in 2009. This edition constitutes a t

35、echnical revision. This edition includes the following significant technical changes with respect to the previous edition: Clauses 18 to 22 have been adapted to IEC 61534-1:2011 and include short-circuit test requirements; addition of a new (500 N) classification for the resistance to traffic load a

36、pplied to small surface areas on a flushfloor service unit; BS EN 61534-22:2014 61534-22 IEC:2014 4 addition of a new classification for the non-automatic closing of the lid on flushfloor service units and appropriate tests; addition of tests for floor service units declared for use when a floor is

37、wet-treated. The text of this standard is based on the following documents: FDIS Report on voting 23A/702/FDIS 23A/708/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordan

38、ce with the ISO/IEC Directives, Part 2. This standard is to be used in conjunction with IEC 61534-1:2011, Powertrack systems Part 1: General requirements. This Part 22 supplements or modifies the corresponding clauses of IEC 61534-1. Where a particular clause or subclause of IEC 61534-1:2011 is not

39、mentioned in this Part 22, that clause or subclause applies as far as is reasonable. Where this Part 22 states “addition“ or “replacement“, the relevant text of IEC 61534-1:2011 is to be adapted accordingly. Subclauses, tables and figures which are in addition to those in IEC 61534-1:2011 are number

40、ed starting with 101. A list of all parts of IEC 61534 series, published under the general title Powertrack systems, can be found on the IEC website. The following differences exist in the countries indicated below: Subclause 7.105.2: In the United Kingdom, this classification is not permitted. The

41、committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised

42、edition, or amended. BS EN 61534-22:2014 61534-22 IEC:2014 5 POWERTRACK SYSTEMS Part 22: Particular requirements for powertrack systems intended for onfloor or underfloor installation 1 Scope Clause 1 of IEC 61534-1:2011 and IEC 61534-1:2011/AMD1:2014 is applicable except as follows: 1.1 Addition: T

43、his part of IEC 61534 specifies the particular requirements and tests for PT systems intended for mounting on, or under the floor level and floor service units which are mounted on the floor, under the floor or flush with the floor. NOTE 1 Types and applications are shown in Figures AA.1a, AA.1b and

44、 AA.2 NOTE 2 Flushfloor PT systems, with the exception of flushfloor service units, are not covered by this standard. 2 Normative references Clause 2 of IEC 61534-1:2011 is applicable except as follows: Addition: IEC 61534-1:2011, Powertrack systems Part 1: General requirements IEC 61534-1:2011/AMD1

45、:2014 3 Terms and definitions Clause 3 of IEC 61534-1:2011 and IEC 61534-1:2011/AMD1:2014 is applicable except as follows: Additional terms and definitions: 3.101 underfloor PT system PT system whose components, except flushfloor service units, are intended for installation beneath the finished floo

46、r and in normal use are not exposed to traffic loads Examples are shown in Figures AA.1a and AA.1b 3.102 onfloor PT system PT system whose components are mounted on the floor surface An example is shown in Figure AA.2. BS EN 61534-22:2014 61534-22 IEC:2014 6 3.103 finished floor floor which carries

47、the traffic load and which may be made of concrete, wood, or the like and which may or may not be completed with floor covering material such as carpet, tile, paint, parquet or similar means 3.104 apparatus mounting device system component to accommodate electrical apparatus, for example switches, s

48、ocket- outlets, circuit-breakers 3.105 floor service unit system component used with a floor system and intended to accommodate one or more electrical apparatus such as switches, socket-outlets, circuit-breakers either directly or by use of mounting devices 3.106 flushfloor service unit floor servic

49、e unit that is flush with the finished floor when the unit is not in use 3.107 in-use floor service unit floor service unit which has cables and/or cords connected to external electrical appliances 3.108 not in-use floor service unit floor service unit which has no cables and/or cords connected to external electrical appliances 4 General requirements Clause 4 of IEC 61534-1:2011 is applicable. 5 General notes on tests Clause 5 of IEC 61534-1:2011 is applicable. 6 Ratings Clause 6 of IEC 6153