BS EN 61386-1-2008 Conduit systems for cable management -Part 1 General requirements《电缆管理用导管系统 第1部分 一般要求》.pdf

《BS EN 61386-1-2008 Conduit systems for cable management -Part 1 General requirements《电缆管理用导管系统 第1部分 一般要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61386-1-2008 Conduit systems for cable management -Part 1 General requirements《电缆管理用导管系统 第1部分 一般要求》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 61386-1:2008Conduit systems for cable management Part 1: General requirementsICS 29.120.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g5

2、5g3g47g36g58BS EN 61386-1:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2008 BSI 2008ISBN 978 0 580 56408 6National forewordThis British Standard is the UK implementation of EN 61386-1:2008. It is identical to IEC 61386-1:2

3、008. It supersedes BS EN 61386-1:2004, which will be withdrawn on 1 June 2011.The UK participation in its preparation was entrusted to Technical Committee PEL/213, Cable management.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does

4、 not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARD EN 61386-1 NORME EUROPE

5、NNE EUROPISCHE NORM August 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any

6、 form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61386-1:2008 E ICS 29.120.10 Supersedes EN 61386-1:2004English version Conduit systems for cable management - Part 1: General requirements (IEC 61386-1:2008) Systmes de conduits pour la gestion du cblage - Partie 1: Exigences

7、 gnrales (CEI 61386-1:2008) Elektroinstallationsrohrsysteme fr elektrische Energie und fr Informationen - Teil 1: Allgemeine Anforderungen (IEC 61386-1:2008) This European Standard was approved by CENELEC on 2008-06-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations wh

8、ich stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This Europea

9、n Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the

10、 national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,

11、Sweden, Switzerland and the United Kingdom. Foreword The text of document 23A/553/FDIS, future edition 2 of IEC 61386-1, prepared by SC 23A, Cable management systems, of IEC TC 23, Electrical accessories, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61386-1 on 200

12、8-06-01. This European Standard supersedes EN 61386-1:2004 + corrigendum April 2004. The changes to EN 61386-1:2004 are as follows: change to the length of the test specimen between fittings for the tensile test, editorial and normative reference updates. The following dates were fixed: latest date

13、by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-06-01 This Part 1 is to be used in conjunction with the appr

14、opriate Part 2, which contains clauses to supplement or modify the corresponding clauses in Part 1, to provide the relevant particular requirements for each type of product. A conduit system which conforms to this standard is deemed safe for use. In this publication, the following print types are us

15、ed: Requirements proper: in roman type. Test specifications: in italic type. Explanatory matter: in smaller roman type. For this European Standard the references to Austria and Australia in Subclauses 6.5.2 and 13.1.4 of IEC 61386-1:2008 shall be disregarded and have been replaced by the normative A

16、nnex ZB, Special national conditions. Annexes ZA and ZB have been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61386-1:2008 was approved by CENELEC as a European Standard without any modification. _ BS EN 61386-1:2008 2 CONTENTS 1 Scope.5 2 Normative references .

17、5 3 Terms and definitions .5 4 General requirements.7 5 General conditions for tests7 6 Classification8 6.1 According to mechanical properties.8 6.1.1 Resistance to compression8 6.1.2 Resistance to impact .8 6.1.3 Resistance to bending .9 6.1.4 Tensile strength.9 6.1.5 Suspended load capacity9 6.2 A

18、ccording to temperature 9 6.2.1 Lower temperature range.9 6.2.2 Upper temperature range.10 6.3 According to electrical characteristics10 6.3.1 With electrical continuity characteristics 10 6.3.2 With electrical insulating characteristics 10 6.3.3 With electrical continuity and insulating characteris

19、tics10 6.4 According to resistance to external influences .10 6.4.1 Protection against ingress of solid objects: protection in accordance with IEC 60529 to a minimum of IP3X10 6.4.2 Protection against ingress of water: protection in accordance with IEC 60529 to a minimum of IPX0 .10 6.4.3 Resistance

20、 against corrosion.10 6.5 According to resistance to flame propagation 10 6.5.1 Non-flame propagating 10 6.5.2 Flame propagating.10 7 Marking and documentation10 8 Dimensions 11 9 Construction.11 10 Mechanical properties 13 10.1 Mechanical strength 13 10.2 Compression test 14 10.3 Impact test 14 10.

21、4 Bending test 15 10.5 Flexing test .15 10.6 Collapse test .15 10.7 Tensile test .15 10.8 Suspended load test16 11 Electrical properties17 11.1 Electrical requirements17 11.2 Bonding test 17 11.3 Dielectric strength and insulation resistance18 BS EN 61386-1:2008 3 12 Thermal properties .19 13 Fire h

22、azard.20 13.1 Reaction to fire20 13.1.1 Initiation of fire 20 13.1.2 Contribution to fire.20 13.1.3 Spread of fire 20 13.1.4 Additional reaction to fire characteristics .22 13.2 Resistance to fire 22 14 External influences .22 14.1 Degree of protection provided by enclosure.22 14.1.1 General .22 14.

23、1.2 Degree of protection Ingress of foreign solid objects.22 14.1.3 Degree of protection Ingress of water .22 14.2 Resistance against corrosion.23 15 Electromagnetic compatibility .24 Annex A (normative) Classification coding for conduit systems 32 Annex B (normative) Determination of material thick

24、ness.35 Bibliography37 Figure 1 Arrangement for compression test25 Figure 2 Impact test apparatus.25 Figure 3 Assembly of conduit and conduit fitting for bonding test .26 Figure 4 Arrangement for dielectric strength and insulation resistance tests Rigid conduit27 Figure 5 Arrangement for dielectric

25、strength and insulation resistance tests Pliable and flexible conduit.28 Figure 6 Steel enclosure for test for resistance to flame propagation .29 Figure 7 Test arrangement for resistance to flame propagation30 Figure 8 Test apparatus for resistance to heat .31 Table 1 Lower temperature range 9 Tabl

26、e 2 Upper temperature range 10 Table 3 Torque values for screw tests13 Table 4 Compression force 14 Table 5 Impact test values .15 Table 6 Tensile force .16 Table 7 Suspended load 17 Table 8 Load for heating test .19 Table 9 Times of exposure of the sample to the flame .21 Table 10 Resistance to cor

27、rosion classification23 Annex ZA (normative) Normative references to international publications with theircorresponding European publications38Annex ZB (normative) Special national conditions39 BS EN 61386-1:2008 4 CONDUIT SYSTEMS FOR CABLE MANAGEMENT Part 1: General requirements 1 Scope This part o

28、f IEC 61386 specifies requirements and tests for conduit systems, including conduits and conduit fittings, for the protection and management of insulated conductors and/or cables in electrical installations or in communication systems up to 1 000 V a.c. and/or 1 500 V d.c. This standard applies to m

29、etallic, non-metallic and composite conduit systems, including threaded and non-threaded entries which terminate the system. This standard does not apply to enclosures and connecting boxes which come within the scope of IEC 60670. NOTE 1 Certain conduit systems may also be suitable for use in hazard

30、ous atmospheres. Regard should then be taken of the extra requirements necessary for equipment to be installed in such conditions. NOTE 2 Earthing conductors may or may not be insulated. 2 Normative references The following referenced documents are indispensable for the application of this document.

31、 For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60417, Graphical symbols for use on equipment IEC 60423:2007, Conduit systems for cable management Outside diameters of conduits for el

32、ectrical installations and threads for conduits and fittings IEC 60529:1989, Degrees of protection provided by enclosures (IP Code) Amendment 1 (1999) IEC 60695-2-11:2000, Fire hazard testing Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products IEC 606

33、95-11-2:2003, Fire hazard testing Part 11-2: Test flames - 1 kW nominal pre-mixed flame - Apparatus, confirmatory test arrangement and guidance 3 Terms and definitions For the purposes of this document, the following definitions apply: 3.1 conduit system cable management system consisting of conduit

34、s and conduit fittings for the protection and management of insulated conductors and/or cables in electrical or communication installations, allowing them to be drawn in and/or replaced, but not to be inserted laterally BS EN 61386-1:2008 5 3.2 conduit part of conduit system of circular cross-sectio

35、n for insulated conductors and/or cables in electrical or communication installations, allowing them to be drawn in and/or replaced 3.3 conduit fitting device designed to join components of a conduit system, or for them to change direction 3.4 terminating conduit fitting conduit fitting that termina

36、tes a conduit system 3.5 metallic conduit and/or conduit fitting conduit or conduit fitting which consists of metal only 3.6 non-metallic conduit and/or conduit fitting conduit or conduit fitting which consists uniquely of non-metallic material and which has no metallic components whatsoever 3.7 com

37、posite conduit and/or conduit fitting conduit or conduit fitting comprising both metallic and non-metallic materials 3.8 non-flame propagating conduit and/or conduit fitting conduit or conduit fitting which is liable to catch fire as a result of an applied flame, but in which the flame does not prop

38、agate, and which extinguishes itself within a limited time after the flame is removed 3.9 plain conduit conduit in which the profile is even in the longitudinal section (see note to 3.10) 3.10 corrugated conduit conduit in which the profile is corrugated in the longitudinal section NOTE Both annular

39、 and helical corrugated conduits are permissible, and a combination of both corrugated and plain conduit is possible. 3.11 rigid conduit conduit which cannot be bent, or which can only be bent with the help of a mechanical aid, with or without special treatment 3.12 pliable conduit conduit which can

40、 be bent by hand with reasonable force, and which is not intended for frequent flexing 3.13 flexible conduit conduit which can be bent by hand with reasonable small force, and which is intended to flex frequently throughout its life BS EN 61386-1:2008 6 3.14 self-recovering conduit pliable conduit w

41、hich deforms when a transverse force is applied for a short time and which, after removal of this force, returns close to its original shape within a further short time 3.15 threadable conduit and conduit fitting conduit and conduit fittings which carry a thread for connection, or in or on which a t

42、hread can be formed 3.16 non-threadable conduit and conduit fitting conduit and conduit fittings which are suitable for connection only by means other than threads 3.17 external influence factors which may affect the conduit system NOTE Examples of such factors are a presence of water, oil or buildi

43、ng materials, low and high temperatures, and corrosive or polluting substances. 4 General requirements 4.1 Conduit and conduit fittings shall be so designed and constructed that in normal use their performance is reliable and they provide protection to the user or surroundings. When assembled in acc

44、ordance with manufacturers instructions as part of a conduit system, conduits and conduit fittings shall provide mechanical and, where required, electrical protection of the insulated conductors and cables contained therein. 4.2 The protective properties of the joint between the conduit and conduit

45、fitting shall not be less than that declared for the conduit system. 4.3 Conduit and conduit fittings shall withstand the stresses likely to occur during transport, storage, recommended installation practice and application. 4.4 Compliance is checked by carrying out all specified tests. 5 General co

46、nditions for tests 5.1 Tests in accordance with this standard are type tests. Conduit systems, having the same classification, which can vary in colour only, shall be the same product type. 5.2 Unless otherwise specified, the tests shall be carried out at an ambient temperature of (20 5) C. 5.3 Unle

47、ss otherwise specified, each test shall be made on three new samples, which may be taken from one length. NOTE Certain tests, for instance the checking of dimensions, do not affect a change in the property of the samples; therefore these samples are considered as new samples and can be used for furt

48、her tests. BS EN 61386-1:2008 7 5.4 Samples of non-metallic and composite conduits and conduit fittings shall be conditioned for at least 240 h, at a temperature of (23 2) C and a relative humidity between 40 % and 60 %. All tests shall be carried out immediately after general conditioning. 5.5 Unle

49、ss otherwise specified, the samples for each test shall be in a clean and new condition, with all parts in place and mounted as in normal use. After checking dimensions in accordance with Clause 8, and unless otherwise specified in the relevant test, the conduit fittings shall be assembled with adequate lengths of conduit of the type for which they are intended. Due regard shall be taken of the manufacturers instructions, especially where force is required in the assembly of