BS EN 61314-1-1-2012 Fibre optic interconnecting devices and passive components Fibre optic fan-outs Blank detail specification《纤维光学互连器件和无源元件 光纤输出端 空白详细规范》.pdf

《BS EN 61314-1-1-2012 Fibre optic interconnecting devices and passive components Fibre optic fan-outs Blank detail specification《纤维光学互连器件和无源元件 光纤输出端 空白详细规范》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61314-1-1-2012 Fibre optic interconnecting devices and passive components Fibre optic fan-outs Blank detail specification《纤维光学互连器件和无源元件 光纤输出端 空白详细规范》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationFibre optic interconnecting devices and passive components Fibre optic fan-outsPart 1-1: Blank detail specificationBS EN 61314-1-1:2012National forewordThis British Standard is t

2、he UK implementation of EN 61314-1-1:2012. It is identical to IEC 61314-1-1:2011. It supersedes BS EN 61314-1-1:2006,which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnecting devices and

3、 passive components.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Publ

4、ished by BSI Standards Limited 2012 ISBN 978 0 580 70938 8 ICS 33.180.10Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2012.Amendments issued since

5、publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 61314-1-1:2012EUROPEAN STANDARD EN 61314-1-1 NORME EUROPENNE EUROPISCHE NORM February 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnis

6、che Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61314-1-1:2012 E ICS 33.180.20 Supersedes EN 61314-1-1:2006English version Fibre optic interconnecting devices

7、 and passive components - Fibre optic fan-outs - Part 1-1: Blank detail specification (IEC 61314-1-1:2011) Dispositifs dinterconnexion et composantspassifs fibres optiques - Systmes dclatement pour fibres optiques - Partie 1-1: Spcification particulire cadre(CEI 61314-1-1:2011) Lichtwellenleiter -Ve

8、rbindungselemente und passive Bauteile - Lichtwellenleiteraufteiler - Teil 1-1: Vordruck fr Bauartspezifikation (IEC 61314-1-1:2011) This European Standard was approved by CENELEC on 2011-12-22. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditi

9、ons for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exis

10、ts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the nati

11、onal electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spa

12、in, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61314-1-1:2012EN 61314-1-1:2012 Foreword The text of document 86B/3271/FDIS, future edition 3 of IEC 61314-1-1, prepared by SC 86B, “Fibre optic interconnecting devices and passive components“, of IEC/TC 86, “Fibre optics“ was submitted t

13、o the IEC-CENELEC parallel vote and approved by CENELEC as EN 61314-1-1:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2012-09-22 latest date by which the national

14、 standards conflicting with the document have to be withdrawn (dow) 2012-12-22 This document supersedes EN 61314-1-1:2006. The specific technical change from EN 61314-1-1:2006 is to reconsider quality approval and quality conformance inspection and to add the mechanical and optical interface standar

15、ds into the detail specification worksheet. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the Interna

16、tional Standard IEC 61314-1-1:2011 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61073 series NOTE Harmonized in EN 61073 series. IEC 61300 series NOTE Harmoniz

17、ed in EN 61300 series. BS EN 61314-1-1:2012EN 61314-1-1:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its

18、application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applie

19、s. Publication Year Title EN/HD Year IEC 60874-1 2006 Connectors for optical fibres and cables - Part 1: Generic specification EN 60874-1 2007 IEC 61314-1 2009 Fibre optic interconnecting devices and passive components - Fibre optic fan-outs - Part 1: Generic specification EN 61314-1 2009 BS EN 6131

20、4-1-1:201261314-1-1 IEC:2011 CONTENTS 1 Scope . . 5 2 Normative references . 5 3 Qualification inspection 5 3.1 Procedure . . 5 3.2 Test schedule and performance requirements . 5 4 Quality conformance inspection . . 5 4.1 Lot-by-lot and periodic procedure . 5 4.2 Lot-by-lot inspection . 6 4.3 Period

21、ic inspection 6 5 Detail specification worksheet . 6 Bibliography . 12 Table 1 Fixed sample inspection schedule for qualification approval 15 9 Table 2 Lot-by-lot quality conformance inspection schedule Groups A and B 16 . 10 Table 3 Periodic quality conformance inspection schedule Groups C and D 17

22、 . 10 Table 4 Details, measurements and performance requirements 18 . 11 BS EN 61314-1-1:201261314-1-1 IEC:2011 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS FIBRE OPTIC FAN-OUTS Part 1-1: Blank detail specification 1 Scope This blank detail specification is not, by itself, a specific

23、ation. It is part of the generic specification IEC 61314-1, Fibre optic interconnecting devices and passive components Fibre optic fanouts Part 1: Generic specification. It includes: a blank worksheet with instructions for preparing detail specifications. 2 Normative references The following documen

24、ts, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60874-1:2006, Connectors

25、 for optical fibres and cables Generic specification IEC 61314-1:2009, Fibre optic interconnecting devices and passive components Fibre optic fan-outs Part 1: Generic specification 3 Qualification inspection 3.1 Procedure The detail specification shall state the qualification approval procedure to b

26、e used, either the fixed sample or the lot-by-lot and periodic procedure may be used. 3.2 Test schedule and performance requirements The mandatory test schedules for qualification by the fixed sample procedure are defined in Table 1 of the detail specification worksheet (see Clause 4). The fixed sam

27、ple procedure consists in subjecting a sample of specimens to the fixed sample qualification test sequence as specified in Table 1. The sample shall be drawn from current production. 4 Quality conformance inspection 4.1 Lot-by-lot and periodic procedure The lot-by-lot and periodic procedure consists

28、 in performing the lot-by-lot inspections on a specified number of inspection lots (a minimum of three) taken in as short a time as possible. The periodic tests are then performed on samples selected from at least one of the lots. BS EN 61314-1-1:2012 6 61314-1-1 IEC:2011 Samples shall be selected f

29、rom the lots in accordance with IEC 60410. Normal inspection shall be used, but when the sample size is so small that acceptance based on zero defects is implied, additional specimens shall be taken to meet the sample size requirements for acceptance on one defect 4.2 Lot-by-lot inspection The manda

30、tory inspection schedules for lot-by-lot inspection (groups A and B) are defined in the detail specification worksheet (see Clause 5). 4.3 Periodic inspection The mandatory inspection schedules for periodic inspection (groups C and D) are defined in the detail specification worksheet (see Clause 5).

31、 5 Detail specification worksheet The following worksheet is provided to aid in the preparation of detail specifications. Spaces are provided for entering information. When the spaces are completed, the detail specification can be drafted in its final form. The spaces are identified by numbers betwe

32、en square brackets. Instructions for completing these numbered spaces are given below. When drafting the final detail specification, eliminate the square-bracketed instruction numbers. 1 The national IEC number assigned to the detail specification is added by the National Committee. 2 The date of th

33、e detail specification is added by the National Committee. 3 Enter the name and address of the National Committee. 4 Enter the applicable classification categories (see 4.2 of IEC 61314-1). 5 Enter the connector/splice type name. 6 Enter the fan-out configuration. 7 Enter the applicable mechanical i

34、nterface standard. If the connectors of the fan-out do not conform to a mechanical interface standard, add the words “not applicable“. 8 Enter the applicable optical interface standard. If the connectors of the fan-out do not conform to an optical interface standard, add the words “not applicable“.

35、9 Enter the performance standard. If the connectors of the fan-out do not conform to a performance standard, add the words “not applicable“. 10 Add the qualification procedure required for the detail specification (fixed-sample procedure or lot-by-lot procedure. 11 Specify the component(s) control d

36、imensions in the format shown (see 4.3.3 of IEC 61314-1). Include: outline drawings and dimensions of the entire fan-out and of the component parts (with the exception of the connectors and/or splices). When a connector standard type interface is referenced, these dimensions shall fall within the ma

37、ting face BS EN 61314-1-1:201261314-1-1 IEC:2011 7 dimensions defined for the type in the relevant Interface Standard (see 4.2.3.3 of IEC 60874-1); control dimensions for all variants; outline drawing and dimension of any special mounting device required for storage and protection of the fan-out, wh

38、ere applicable; measurement method(s) to be used when the requirements of 4.3.4.1 of IEC 61314-1 apply. Add figures showing the dimensions for standard reference components and gauges, if required (see 4.3.3 of IEC 61314-1). Display the drawings in the format shown. 12 Tabulate the identification nu

39、mber for each variant of each component (see 4.8.1 of IEC 61314-1). Assign a column in the table for each variant feature. For example, number of fibres or channels, fibre or cable sizes, etc. 13 Specify the test fibre/cable for kit arrangement samples. If the detail specification does not cover a k

40、it arrangement, eliminate the table. 14 Enter supplementary information with respect to marking, requirements for certified records of released lots, and other appropriate information (see 4.8.2 and 4.8.3 of IEC 61314-1). 15 Table 1 defines the measurements and tests for qualification by fixed sampl

41、e size. If qualification by lot-by-lot and periodic procedure is specified, eliminate the tables and renumber subsequent tables in the detail specification accordingly. Specify the sample size for each group in column n. 16 Table 2 defines the minimum measurements and tests, required for groups A an

42、d B. Detail specification writers must add those tests or measurements to be carried out to the table. Add the assessment level designation along with the inspection level and AQL in the appropriate place in the tables (see 4.2.5 of IEC 61314-1). 17 Table 3 defines the measurements and tests require

43、d for groups C and D periodic tests. Add the assessment level designation together with the sample size, n, and the inspection period, p, in the appropriate place in the tables (see 4.2.5 of IEC 61314-1). After completing the group C0 or D0 measurements and tests, the sample is divided to form the o

44、ther sample groups. When needed, instructions for dividing the sample are given as a note to the tables. 18 When completed, Table 4 will contain the details, measurements and the performance requirements for all tests and measurements which appear in Tables 1, 2 and 3. The format for measurements ap

45、pears on lines 19, 20, and 21. Enter the measurement procedure title and reference location on line 19 and the measurement details on line 20. The requirements for independent measurements (measurements which are not part of an environmental test) shall either be specified as a note to the tables wh

46、ere it was added (Tables 1, 2 or 3), or included in Table 4 under the appropriate measurement on line 20. The requirements for dependent measurements (measurements which are part of an environmental test) shall be specified under the environmental test in Table 4. BS EN 61314-1-1:2012 8 61314-1-1 IE

47、C:2011 The format for environmental tests appears on lines 22, 23, 24, 25, and 26. Enter the test procedure title and reference location on line 22. Enter the test details on line 23. Enter the initial measurements to be made along with the performance requirements on line 24. Enter the measurements

48、 to be made during the test together with the performance requirements on line 25. Enter the final measurements to be made together with the performance requirements on line 26. NATIONAL STANDARDS ORGANIZATION: 3 1 Date. 2 DETAIL SPECIFICATION FIBRE OPTIC COMPONENT OF ASSESSED QUALITY IN ACCORDANCE WITH Generic specification: IEC 61314-1, QC 880000 Blank detail specification: IEC 61314-1-1, QC 880001 FAN-OUT CLASSIFICATION: 4 Type: Name. 5 Configuration: (see figure) 6 Arrangement: Style: packaging technology:. Variants: see pages Mechanical Interface Standard 7 Optical Interface Standard