BS EN 61313-1-1997 Fibre optic passive components and cable assemblies - Capability approval - Generic specification《光纤无源部件和电缆组件 第1部分 能力鉴定 通用规范》.pdf

《BS EN 61313-1-1997 Fibre optic passive components and cable assemblies - Capability approval - Generic specification《光纤无源部件和电缆组件 第1部分 能力鉴定 通用规范》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61313-1-1997 Fibre optic passive components and cable assemblies - Capability approval - Generic specification《光纤无源部件和电缆组件 第1部分 能力鉴定 通用规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61313-1:1997 IEC61313-1: 1995 Fibre optic passive components and cable assemblies Part1: Capability approval Genericspecification The European Standard EN61313-1:1997 has the status of a BritishStandard ICS33.180.20BSEN61313-1:1997 This BritishStandard, having been prepared un

2、der the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comesintoeffect on 15 August1997 BSI03-2000 ISBN 0 580 27801 8 National foreword This BritishStandard is the English language version of EN61313-1:1997. Itis identical with IEC61313-1:1

3、995. The UK participation in its preparation was entrusted by Technical Committee EPL/86, Fibre optics, to Subcommittee EPL/86/2, Interconnecting devices and passive components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European c

4、ommittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From

5、1 January1997, all IEC publications have the number60000 added to the old number. For instance, IEC27-1 has been renumbered as IEC60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Atte

6、ntion is drawn to the fact that Annex ZA lists normative references to international publications with their corresponding European publications. The BritishStandards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “

7、International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with

8、a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may

9、have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN61313-1:1997 BSI 03-2000 i Contents Page National foreword Inside front cover Foreword 2 Text of EN61313-1 3ii blankEUROPEAN STANDA

10、RD NORME EUROPENNE EUROPISCHE NORM EN61313-1 May1997 ICS33.180.20 Descriptors: Capability approval of optic passive components English version Fibre optic passive components and cable assemblies Part1:Capability approval Generic specification (IEC1313-1:1995) Ensembles de cbles et composants passifs

11、fibres optiques Partie1: Agrment de savoir-faire Spcificationgnrique (CEI1313-1:1995) Passive LWL-Bauelemente und konfektionierteLWL-Kabel Teil1: Befhigungsanerkennung Fachgrundspezifikation (IEC1313-1:1995) This European Standard was approved by CENELEC on1997-03-11. CENELEC members are bound to co

12、mply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central S

13、ecretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German), A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status

14、as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CENELEC European Committee for Elec

15、trotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No.

16、 EN61313-1:1997 EEN61313-1:1997 BSI 03-2000 2 Foreword The text of the International Standard IEC1313-1:1995, prepared by SC86B, Fibre optic interconnecting devices and passive components, of IEC TC86, Fibre optics, was submitted to the formal vote and was approved by CENELEC as EN61313-1 on1997-03-

17、11 without any modification. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC1313-1:1995 was approved by CENE

18、LEC as aEuropean Standard without any modification. Contents Page Foreword 2 1 General 3 1.1 Scope 3 1.2 Normative references 3 1.3 Abbreviations 3 2 Requirements 3 2.1 Capability approval 3 2.2 Classification 3 2.3 Documentation 3 2.4 Design and construction 4 2.5 Quality assessment 4 2.6 Identific

19、ation and marking 4 3 Quality assessment procedures 4 3.1 Primary stage of manufacture 4 3.2 Capability approval procedures 5 3.3 Quality conformance inspection 5 3.4 Certified records of released lots 6 3.5 Delayed deliveries 6 3.6 Release before completion of group B tests 6 3.7 Measurements and t

20、est procedures 6 3.8 Unchecked parameters 6 Annex ZA (normative) Normative references to international publications with their corresponding European publications Inside back cover latest date by which the ENhas to be implemented at national level by publication of an identical national standard or

21、by endorsement (dop) 1998-03-01 latest date by which the national standards conflicting with the EN haveto be withdrawn (dow) 1998-03-01EN61313-1:1997 BSI 03-2000 3 1 General 1.1 Scope This specification applies to fibre optic passive components and cable assemblies for delivery under the capability

22、 approval procedure. It includes: component and cable assembly requirements; quality assessment procedures. 1.2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this specification. At the time of publication, th

23、e editions indicated were valid. All standards are subject to revision and parties to agreements based on this specification are encouraged to apply the most recent editions of the normative documents indicated below. Members of IEC and ISO maintain registers of currently valid International Standar

24、ds. IEC68, Environmental testing. IEC68-1:1988, Environmental testing Part1:General and guide. IEC410:1973, Sampling plans and procedures for inspection by attributes. IEC695-2-2:1991, Fire hazard testing Part2:Test methods Section2: Needle-flame test. IEC1300:1995, Basic measurement and test proced

25、ures for passive fibre optic components. IEC QC001001:1986, Basic rules of the IEC Quality Assessment System for Electronic Components (IECQ). IEC QC001002:1986, Rules of Procedure of the IECQuality Assessment System for Electronic Components (IECQ). IEC Guide102:1989, Electronic components Specific

26、ation structures for quality assessment (Qualification approval and capability approval). ISO8601:1988, Data elements and interchange formats Information interchange Representation of dates and times. 1.3 Abbreviations 2 Requirements 2.1 Capability approval Components and cable assemblies furnished

27、to this specification shall be authorized by the NSI for listing on the QPL under the capability approval procedure in accordance with11.7.7 of IECQC001002. 2.2 Classification Components and cable assemblies furnished to this specification shall be classified by assessment level 1) . In addition, th

28、ey may be classified by climatic and environmental categories. 2.2.1 Climatic category Climatic category is defined in Appendix A of IEC68-1. The following are preferred values which may be specified. 2.3 Documentation 2.3.1 Specification system This specification is part of a four-level IECspecific

29、ation system. Subsidiary specifications consist of sectional specifications and detail specifications (according to IEC Guide102). Sectional specifications shall be prepared for each subfamily of components. The specification shall contain: 1) Any additional requirements peculiar to the subfamily. 2

30、) Any additional quality assessment procedures peculiar to the subfamily. 3) Any standard or preferred values and severities which are peculiar to the subfamily. 4) The minimum mandatory test schedules for the subfamily. 5) One or more blank detail specifications. IECQ IEC Quality Assessment System

31、for Electronic Components CQC Capability Qualifying Component CDS Customer Detail Specification QPL Qualified Products List NSI National Supervisory Inspectorate 1) Assessment level is the combination of the CQC periodic inspection and the lot-by-lot inspection on released product. Low temperature C

32、 High temperature C Damp-heat duration Days 5 10 25 40 55 65 +30 +40 +55 +70 +85 +100 +125 +155 +175 +200 4 10 21 56EN61313-1:1997 4 BSI 03-2000 2.3.2 Measurements 2.3.2.1 Reference components The description of capability(3.2.1) shall define reference components as required. 2.3.2.2 Gauges The desc

33、ription of capability(3.2.1) shall define gauges as required. 2.3.3 Test data sheets Prepare test data sheets for each test conducted to the capability test programme. Include the data sheets in the capability approval report(3.2.8) and in the periodic inspection report(3.3.2.3). Include the followi

34、ng minimum information in each data sheet: title of test and date; a complete description of the capability qualifying component(s) including the type of fibre, the type of cable, and the components; test equipment used and date of latest calibration; all applicable test details; all measurement val

35、ues and observations; sufficiently detailed documentation to provide traceable information for failure analysis(see3.2.6 and3.3.2.4). 2.3.4 Safety warnings Each detail specification shall include the following warning: “Care should be taken when handling small diameter optical fibre to prevent punct

36、uring the skin, especially in the eye area. Direct viewing of an optical fibre, when it is propagating energy, is not recommended unless prior assurance has been obtained as to the safe energy output level”. 2.4 Design and construction 2.4.1 Materials 2.4.1.1 Corrosion resistance All materials used

37、in the construction of components or cable assemblies shall be corrosion resistant or shall be suitably finished to meet the requirements of the detail specification. 2.4.1.2 Non-flammable materials When non-flammable materials are required, the requirement shall be specified in the detail specifica

38、tion and IEC695-2-2 shall be referenced. 2.4.2 Workmanship Components or cable assemblies shall be manufactured to a uniform quality. The appropriate manufacturers instructions for use shall be followed when applying components to the fibre/cable. Particular attention shall be given to neatness and

39、thoroughness of marking, soldering, bonding, etc. 2.5 Quality assessment The quality assessment procedures of clause3 shall control the quality of components and cable assemblies covered by this specification. 2.6 Identification and marking Components, cable assemblies, associated hardware and packa

40、ges shall be permanently and legibly marked as required by the detail specification. 2.6.1 Component or cable assembly marking The preferred order of marking for components or cable assemblies is: 1) manufacturers identification mark; 2) manufacturing date code; 3) manufacturers part number. 2.6.2 P

41、ackage marking The preferred order of marking components or cable assemblies is: 1) manufacturers identification mark; 2) manufacturers part number; 3) manufacturing date code (year/week)(seeISO8601); 4) assessment level(s); 5) climatic category; 6) environmental category; 7) additional marking requ

42、ired by the detail specification. 3 Quality assessment procedures Procedures for quality assessment and release of components or cable assemblies consist of: capability approval(2.1); quality conformance inspection(3.3). 3.1 Primary stage of manufacture The primary stage of manufacture for component

43、s or cable assemblies covered by this specification is defined at the manufacturing stage when the parts which make up the individual component or cable assembly are aggregated into the product defined in the detail specification. Subcontracting of the primary stage and subsequent stages is permitte

44、d.EN61313-1:1997 BSI 03-2000 5 3.2 Capability approval procedures 3.2.1 Description of capability The manufacturer shall prepare a description of capability in accordance with11.7.3.2 of IECQC001002. The description shall include: a) the limits of capability; b) the design rules; c) a process flow c

45、hart, including inspection points; d) a list of the specifications for the material and parts used; e) a list of the specifications for the inspections to be carried out; f) a list of the fibres, cables, and components by manufacturers part number. 3.2.2 Capability qualifying component The capabilit

46、y qualifying component may consist of a complete component or cable assembly or any individual subassembly or test piece which will demonstrate the limits of capability defined in the description of capability(3.2.1). 3.2.3 Capability test programme The manufacturer shall provide a capability test p

47、rogramme in accordance with11.7.3.3 of IECQC001002. The programme shall include: a) a description of the CQCs to be used as specimens in the capability approval tests, including instructions for use(see3.2.2); b) a description of the counterpart components 2) ; c) the test schedules for capability a

48、pproval and a test plan. The test plan shall include a complete schedule of test events along with the test requirements; d) the assessment level; e) the climatic category, if specified; f) the environmental category, if specified; g) the test schedules as specified in the applicable sectional speci

49、fication for periodic inspection of the CQCs (groups C and D) and a test plan. Thetest plan shall include a complete schedule of test events, together with the test requirements. The manufacturer shall obtain approval for the test programme from the NSI. 3.2.4 Preparation of specimens The CQCs shall be prepared for testing according to the instructions for use defined in the capability test programme(3.2.3). 3.2.5 Capability approval testing Manufacturers shall conduct the tests in the order given and to the met