BS EN 61300-2-35-2014 Fibre optic interconnecting devices and passive components Basic test and measurement procedures Tests Cable nutation《光纤互联装置和无源部件 基本试验和测量程序 第2部分第35节 试验 电缆下垂》.pdf

《BS EN 61300-2-35-2014 Fibre optic interconnecting devices and passive components Basic test and measurement procedures Tests Cable nutation《光纤互联装置和无源部件 基本试验和测量程序 第2部分第35节 试验 电缆下垂》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61300-2-35-2014 Fibre optic interconnecting devices and passive components Basic test and measurement procedures Tests Cable nutation《光纤互联装置和无源部件 基本试验和测量程序 第2部分第35节 试验 电缆下垂》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationFibre optic interconnecting devices and passive components Basic test and measurement proceduresPart 2-35: Tests Cable nutationBS EN 61300-2-35:2014National forewordThis British Standard is the UK implementation of EN 61300-2-35:2014. It isidentical to IEC 61300-2-35:2014. I

2、t supersedes BS EN 61300-2-35:1997which is withdrawn.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre opticinterconnecting devices and passive components.A list of organizations represented on this committee can be obta

3、ined onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 75736 5ICS 33.180.20Compliance with

4、a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61300-2-35:2014EUROPEAN STANDA

5、RD NORME EUROPENNE EUROPISCHE NORM EN 61300-2-35 July 2014 ICS 33.180.20 Supersedes EN 61300-2-35:1997 English Version Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-35: Tests - Cable nutation (IEC 61300-2-35:2014) Dispositifs dinterconnex

6、ion et composants passifs fibres optiques - Procdures fondamentales dessais et de mesures - Partie 2-35: Essais - Nutation du cble (CEI 61300-2-35:2014) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prf- und Messverfahren - Teil 2-35: Prfungen - Kabelnutation (IEC 61300

7、-2-35:2014) This European Standard was approved by CENELEC on 2014-04-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibl

8、iographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the re

9、sponsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Fi

10、nland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Ele

11、ctrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

12、 Ref. No. EN 61300-2-35:2014 E BS EN 61300-2-35:2014EN 61300-2-35:2014 - 2 - Foreword The text of document 86B/3703/FDIS, future edition 2 of IEC 61300-2-35, prepared by SC 86B “Fibre optic interconnecting devices and passive components“ of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC p

13、arallel vote and approved by CENELEC as EN 61300-2-35:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-01-11 latest date by which the national standards conflic

14、ting with the document have to be withdrawn (dow) 2015-04-11 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes

15、EN 61300-2-35:1997. Endorsement notice The text of the International Standard IEC 61300-2-35:2014 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated: IEC 61753-1 NOTE Harmon

16、ized as EN 61753-1. BS EN 61300-2-35:2014- 3 - EN 61300-2-35:2014 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for

17、 its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD

18、 applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 61300-3-1 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part

19、 3-1: Examinations and measurements - Visual examination EN 61300-3-1 - IEC 61300-3-3 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-3: Examinations and measurements - Active monitoring of changes in attenuation and return loss EN 61300-

20、3-3 - IEC 61300-3-4 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-4: Examinations and measurements - Attenuation EN 61300-3-4 - BS EN 61300-2-35:2014 2 IEC 61300-2-35:2014 IEC 2014 CONTENTS 1 Scope 5 2 Normative references 5 3 Terms and

21、 definitions 5 4 General description . 6 5 Apparatus 6 5.1 Design of the apparatus . 6 5.2 Optical measurements . 9 6 Procedure 9 6.1 Preconditioning 9 6.2 Initial examinations and measurements 9 6.3 Conditioning . 10 6.4 Recovery . 10 6.5 Final examinations and measurements 10 7 Severity . 10 8 Det

22、ails to be specified . 11 Annex A (informative) Example for a test set-up 12 Bibliography 13 Figure 1 Test apparatus with vertical rotating DUT . 7 Figure 2 Test apparatus with horizontal rotating DUT . 8 Figure 3 Test apparatus with rotating deflection unit 9 Figure A.1 Example for a test set-up 12

23、 Table 1 Severities 10 BS EN 61300-2-35:2014IEC 61300-2-35:2014 IEC 2014 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-35: Tests Cable nutation 1 Scope This part of IEC 61300 details procedures for determining the suitability of a fibre opt

24、ic device to withstand nutation that may occur during operation, service, storage and/or transport. The test is intended to indicate the performance of such devices when exposed to torsion and bending as a combined load. 2 Normative references The following documents, in whole or in part, are normat

25、ively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-3-1, Fibre optic interconnecting devices and passive

26、components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61300-3-3, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-3: Examinations and measurements Active monitoring of changes in attenuat

27、ion and return loss IEC 61300-3-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-4: Examinations and measurements Attenuation 3 Terms and definitions For the purposes of this document, the terms and definitions contained in the IEC 61300 seri

28、es, some of which have been repeated here for convenience, and the following terms and definitions apply. 3.1 deflection unit rotating element with a cable feed through, able to describe a circle without transmitting substantial torque to the cable 3.2 fixed clamping device clamping device which pre

29、vents the device under test (DUT) moving during the test 3.3 fixed plate plate with a cable feed through able to constrain any movement and twist of the cable in relation to the DUT BS EN 61300-2-35:2014 6 IEC 61300-2-35:2014 IEC 2014 3.4 weight element which applies the required tensile force to th

30、e cable end 3.5 nutation combined flexing-rotation movements with tensile force 3.6 pulley swivel pulley 3.7 rotating clamping device clamping device, able to describe a circle without transmitting axial rotation to the DUT 4 General description The purpose of environmental testing is to demonstrate

31、 that the DUT, under defined environmental conditions, is able to survive without irreversible or reversible failures according to the requirements. The specimen is placed on the apparatus and subjected to a flexing rotation which is maintained at a given temperature and relative humidity for a spec

32、ified duration, as specified in the relevant specification. 5 Apparatus 5.1 Design of the apparatus The apparatus performs a flexing rotation, substantially without torque, of the cable adjacent to the DUT in a conical path, with the axis of the cone being parallel with the longitudinal axis of the

33、specimen. During the rotation a tensile force is applied to the cable. Either the DUT or the deflection unit may rotate, depending on the design of the apparatus. Examples of the test apparatus are given in Figure 1, Figure 2 and Figure 3. BS EN 61300-2-35:2014IEC 61300-2-35:2014 IEC 2014 7 Figure 1

34、 Test apparatus with vertical rotating DUT The test apparatus in Figure 1 consists at least of the following elements: a) rotating clamping device; b) pulley; c) weight for the tensile force. The size of the pulley should not create additional attenuation during the rotation of the connector. The de

35、sign and size of the pulley should not cause a change in the load at the connector. The maximum radius of the pulley depending on the allowed variation of the cone angle should be calculated with the following equation: ALrmax18= where L is conical path length; A is the deflection angle (null) ; 10%

36、 allowable tolerance of conical path length was assumed. DUTSwivel pulleyxxWeightxxDeflection angle AbarTensileforce RIEC 0412/14 BS EN 61300-2-35:2014 8 IEC 61300-2-35:2014 IEC 2014 Figure 2 Test apparatus with horizontal rotating DUT The test apparatus in Figure 2 consists of at least the followin

37、g elements: 1) rotating clamping device; 2) fixed plate; 3) weight for the tensile force. The cable should be able to move freely and be driven to rotate such that its absolute orientation is maintained. IEC 0413/14 WeightDUTRotating clamping deviceTensileforce RDeflection angle ABS EN 61300-2-35:20

38、14IEC 61300-2-35:2014 IEC 2014 9 Figure 3 Test apparatus with rotating deflection unit The test apparatus in Figure 3 consists of at least the following elements: i) fixed clamping device; ii) deflection unit; iii) weight for the tensile force. The cable should be able to move freely and be driven t

39、o rotate such that its absolute orientation is maintained. 5.2 Optical measurements Where active monitoring is specified, measuring equipment specified in IEC 61300-3-3 shall be connected to the specimen for monitoring optical performance during the test. The optical source and detector used to meas

40、ure changes in attenuation shall comply with those specified in IEC 61300-3-4. 6 Procedure 6.1 Preconditioning Maintain the specimen under standard atmospheric conditions (room temperature condition) for a minimum of 2 h. Clean the specimen according to the manufacturers instructions. 6.2 Initial ex

41、aminations and measurements Complete initial examinations and measurements as required by the relevant specification. IEC 0414/14 DUTFixed clamping deviceWeightDeflection unitDeflection angle ATensile force RBS EN 61300-2-35:2014 10 IEC 61300-2-35:2014 IEC 2014 6.3 Conditioning A tensile force is ap

42、plied to the cable of the terminated assembly. The mated connector assembly is held by the adaptor installed in the clamping device. The force is applied at the deflection angle to the connector axis. The test procedure consists of the following tasks and shall be performed in the following order: a

43、) set up the apparatus to obtain the required deflection angle; b) fix the specimen to the clamping device; c) route the cable and apply the required tensile force to the cable end; d) run the required number of cycles of rotation (360) at a rate of 10 cycles per minute. 6.4 Recovery Allow the speci

44、men to remain under standard atmospheric conditions for a period of 10 min. 6.5 Final examinations and measurements On completion of the test, remove all fixtures. Clean the mechanical and optical alignment parts of the specimen according to the manufacturers instructions. Take final measurements as

45、 required by the relevant specification. If specified, visually examine the specimen in accordance with IEC 61300-3-1 and take any measurements specified to ensure that there is no permanent damage. 7 Severity The severity consists of the combination of the number of cycles of rotation, the deflecti

46、on angle and the tensile force applied to the cable. The severity shall be specified in the relevant specification. The severities according to Table 1 may be used for the procedure. Table 1 Severities Tensile force, R N Deflection angle A Rotation angle Number of cycles Category 10 45 360 100 I BS

47、EN 61300-2-35:2014IEC 61300-2-35:2014 IEC 2014 11 8 Details to be specified The following details, as applicable, shall be specified in the relevant specification: a) description of the DUT; b) cable type; c) tensile force; d) deflection angle; e) number of cycles; f) specific mounting structures; g

48、) specimen optically functioning; h) initial examinations and measurements and performance requirements; i) examinations and measurements during test and performance requirements; j) final examinations and measurements and performance requirements; k) deviations from test procedure; l) additional pa

49、ss/fail criteria. BS EN 61300-2-35:2014 12 IEC 61300-2-35:2014 IEC 2014 Annex A (informative) Example for a test set-up An example of a real test set-up is shown in Figure A.1. Figure A.1 Example for a test set-up IEC 0215/14 BS EN 61300-2-35:2014IEC 61300-2-35:2014 IEC 2014 13 Bibliography IEC 61753-1, Fibre optic interconnecting devices and passive components performance standard Part 1: General and guidance for performance stand