BS EN 61300-2-15-2008 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-15 Tests - Torque strength of coupling mechanism《光.pdf

《BS EN 61300-2-15-2008 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-15 Tests - Torque strength of coupling mechanism《光.pdf》由会员分享，可在线阅读，更多相关《BS EN 61300-2-15-2008 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-15 Tests - Torque strength of coupling mechanism《光.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 61300-2-15:2008Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-15: Tests Torque strength of coupling mechanismICS 33.180.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g4

2、0g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 61300-2-15:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2008 BSI 2008ISBN 978 0 580 57891 5National forewordThis Brit

3、ish Standard is the UK implementation of EN 61300-2-15:2008. It is identical to IEC 61300-2-15:2008. It supersedes BS EN 61300-2-15:1997 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interco

4、nnecting devices and passive components.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a Briti

5、sh Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARD EN 61300-2-15 NORME EUROPENNE EUROPISCHE NORM May 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechniqu

6、e Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61300-2-15:2008 E ICS 33.180.20 Supersedes EN 61300-2-15:1997Englis

7、h version Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-15: Tests - Torque strength of coupling mechanism (IEC 61300-2-15:2008) Dispositifs dinterconnexion et composants passifs fibres optiques - Mthodes fondamentales dessais et de mesure

8、s - Partie 2-15: Essais - Robustesse du mcanisme de verrouillage aux efforts de torsion (CEI 61300-2-15:2008) Lichtwellenleiter -Verbindungselemente und passive Bauteile - Grundlegende Prf- und Messverfahren - Teil 2-15: Prfungen - Torsionsfestigkeit der Verriegelung (IEC 61300-2-15:2008) This Europ

9、ean Standard was approved by CENELEC on 2008-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

10、 concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member

11、 into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, I

12、reland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 86B/2539/CDV, future edition 2 of IEC 61300-2-15, prepared by SC 86B, Fibre optic interconnect

13、ing devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61300-2-15 on 2008-04-01. This European Standard supersedes EN 61300-2-15:1997. Specific technical changes from EN 61300-2-15:1997 include reexamination of

14、 the pre-conditioning. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-01-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow

15、) 2011-04-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61300-2-15:2008 was approved by CENELEC as a European Standard without any modification. _ BS EN 61300-2-15:2008 2 CONTENTS 1 Scope.4 2 Normative references4 3 General description.4 4 App

16、aratus.4 4.1 Stand 4 4.2 Specimen holder4 4.3 Coupling5 4.4 Coupling shaft .5 4.5 Alignment mechanism5 4.6 Torque applicator and gauge .5 5 Procedure.6 5.1 Preparation of specimens 6 5.2 Pre-conditioning 6 5.3 Specimen mounting .6 5.4 Torque loading 6 5.5 Post-test examination 6 6 Severity 6 7 Detai

17、ls to be specified.6 Figure 1 Coupling torque tester 5 BS EN 61300-2-15:2008 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications .8 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Pa

18、rt 2-15: Tests Torque strength of coupling mechanism 1 Scope This part of IEC 61300 applies an overload torque to twist-type coupling mechanisms. It is applicable to threaded or bayonet-twist type coupling mechanisms. It can be used to ensure that the coupling mechanism of a connector set or connect

19、or-device combination will withstand the torsional loads likely to be applied during normal service. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the lat

20、est edition of the referenced document (including any amendments) applies. IEC 61300-3-1: Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination 3 General description A torsional load is smoothly app

21、lied to a mated connector set or connector-device combination in a manner that will over-torque threaded or bayonet twist-type coupling mechanisms. The torque is normally applied between the connector plug and the adapter or between the connector plug and the device being tested. 4 Apparatus The tes

22、t apparatus shall be capable of applying a torque, either manually or automatically, to a threaded or bayonet coupling nut while the adapter or device is held in place. An example of a test apparatus is shown in Figure 1. Some or all of the following apparatus components will be required. 4.1 Stand

23、Use a stand capable of ensuring that the specimen and the torque applicator are always held in the proper relationship during the test. 4.2 Specimen holder The specimen holder shall be a floating fixture to which the device under test is mounted. The holder shall be prohibited from rotating, but sha

24、ll otherwise be capable of moving freely in order to obtain the proper alignment between the coupling nut or cap and the adapter or other device under test. BS EN 61300-2-15:2008 4 Specimen holder Torque gauge and applicator Alignment mechanism Coupling shaftStand Coupling Device under test IEC 090/

25、08 Figure 1 Coupling torque tester 4.3 Coupling Use a coupling designed to mate with the cap or coupling nut of the specimen in a such a manner that the torque is applied orthogonally to the coupling interface without the presence of any bending moment. 4.4 Coupling shaft A coupling shaft shall be u

26、sed to connect the torque applicator through the coupling to the device under test. 4.5 Alignment mechanism Use an alignment mechanism to ensure that the coupling shaft is always in the proper position relative to the specimen. A clearance hole or low friction sleeve bearing will usually be satisfac

27、tory. 4.6 Torque applicator and gauge Torque shall be applied using a torque wrench or equivalent and a torque gauge, having a torque range of no more than three times the required torque test value. A maximum reading torque indicator is preferred, but not required. The gauge shall be accurate to wi

28、thin 10 % of the applied torque value. BS EN 61300-2-15:2008 5 5 Procedure 5.1 Preparation of specimens Mate the device to be tested according to the manufacturers instructions. For screw type couplings, use a torque wrench to ensure that the couplings are tightened to the proper value. 5.2 Pre-cond

29、itioning Pre-condition the prepared specimens for 2 h at the standard test conditions specified in IEC 61300-1 before beginning the test, unless otherwise specified in the relevant specification. 5.3 Specimen mounting Securely mount each specimen under test, usually the connector adapter, switch, at

30、tenuator, etc., to the stationary portion of the test fixture. Connect the torque applicator to the plug cap or coupling nut through the coupling, coupling shaft and alignment mechanism. 5.4 Torque loading Using the torque applicator, smoothly apply the specified torque to the cap or coupling nut at

31、 a nominal rate such that there is no element of impact loading. Unless otherwise specified in the relevant specification, maintain the specified torque for a minimum period of 15 s. 5.5 Post-test examination Remove the torque load and remove the specimen from the mounting. Unless otherwise specifie

32、d, examine the specimen and its component parts in accordance with the requirements of IEC 61300-3-1. Check for any evidence of cracking, bending or permanent deformation. Check for other damage which might impair its function, and any other pass/fail criteria specified in the relevant specification

33、. 6 Severity The severity of the test is dependant upon the magnitude of the applied torque and to a lesser extent the duration of the load. The magnitude and duration of the load shall be given in the relevant specification. The following preferred severities are non-mandatory severities which may

34、be applied to this test: Overload torques N m 0,4 0,6 0,8 7 Details to be specified The following details, as applicable, shall be specified in the relevant specification: magnitude of overload torque; required coupling torque; duration of torque application, if other than 15 s; BS EN 61300-2-15:200

35、8 6 pre-conditioning procedure, if different from 5.2; recovery procedure; specimen optical functioning or not functioning; specimen mated or unmated; initial examinations and measurements and performance requirements; examinations and measurements during test and performance requirements, if requir

36、ed; final examinations and measurements and performance requirements; deviations from the test procedure; additional pass/fail criteria. _ BS EN 61300-2-15:2008 7 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following refe

37、renced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common

38、modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 61300-3-1 -1)Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-1: Examinations and measurements - Visual examination EN 61300-3-1 20052)1)Und

39、ated reference. 2)Valid edition at date of issue. BS EN 61300-2-15:2008 8 blankBS EN 61300-2-15:2008BSI Group Headquarters389 Chiswick High Road,London W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards Institution (BSI)BSI is the independent national body responsible for preparing Briti

40、sh Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the

41、constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover

42、. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addres

43、sed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been pub

44、lished as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available w

45、hich give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of

46、 these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/.Copyright

47、Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any

48、 form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: