BS EN 61290-1-1-2015 Optical amplifiers Test methods Power and gain parameters Optical spectrum analyzer method《光纤放大器 试验方法 第1-1部分 功率和增益参数 光学频谱分析仪法》.pdf

《BS EN 61290-1-1-2015 Optical amplifiers Test methods Power and gain parameters Optical spectrum analyzer method《光纤放大器 试验方法 第1-1部分 功率和增益参数 光学频谱分析仪法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61290-1-1-2015 Optical amplifiers Test methods Power and gain parameters Optical spectrum analyzer method《光纤放大器 试验方法 第1-1部分 功率和增益参数 光学频谱分析仪法》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationOptical amplifiers Test methodsPart 1-1: Power and gain parameters Optical spectrum analyzer methodBS EN 61290-1-1:2015National forewordThis British Standard is the UK implementation of EN 61290-1-1:2015. It is identical to IEC 61290-1-1:2015. It supersedes BS EN 61290-1-1:2

2、006 which is withdrawn.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/3, Fibre optic systems and active devices.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication

3、does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83954 2ICS 33.180.30Compliance with a British Standard cannot confer immunity fromleg

4、al obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61290-1-1:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61290-1-1 July

5、 2015 ICS 33.180.30 Supersedes EN 61290-1-1:2006 English Version Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method (IEC 61290-1-1:2015) Amplificateurs optiques - Mthodes dessai - Partie 1-1: Paramtres de puissance et de gain - Mthode de lanaly

6、seur de spectre optique (IEC 61290-1-1:2015) Prfverfahren fr Lichtwellenleiter-Verstrker - Teil 1-1: Optische Leistungs- und Verstrkungsparameter - Verfahren mit optischem Spektralanalysator (IEC 61290-1-1:2015) This European Standard was approved by CENELEC on 2015-06-11. CENELEC members are bound

7、to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-

8、CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Ce

9、ntre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, It

10、aly, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr

11、 Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61290-1-1:2015 E BS EN 61290-1-1:2015EN 61290-1-1:2015 2 European foreword The text of

12、document 86C/1309/FDIS, future edition 3 of IEC 61290-1-1, prepared by SC 86C “Fibre optic systems and active devices“ of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61290-1-1:2015. The following dates are fixed: latest date by which the docu

13、ment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2016-03-11 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-06-11 This document supersedes EN 61290-1-1:2006 and constitutes

14、a technical revision. EN 61290-1-1:2015 includes the following significant technical changes with respect to the previous edition: a) updates on the characteristics of measurement apparatus; b) revised list of addressed optical amplifier parameters. EN 61290-1-1:2015 shall be used in conjunction wit

15、h EN 61290-1 and EN 61291-1. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard

16、 IEC 61290-1-1:2015 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61290-10 NOTE Harmonized in EN 61290-10 series (not modified). IEC 60793-2-50 NOTE Harmonized

17、as EN 60793-2-50. BS EN 61290-1-1:2015EN 61290-1-1:2015 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its app

18、lication. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies

19、. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 61290-1 - Optical amplifiers - Test methods - Part 1: Power and gain parameters EN 61290-1 - IEC 61291-1 - Optical amplifiers

20、 - Part 1: Generic specification EN 61291-1 - BS EN 61290-1-1:2015 2 IEC 61290-1-1:2015 IEC 2015 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms, definitions and abbreviations . 5 3.1 Terms and definitions 5 3.2 Abbreviations 5 4 Apparatus 6 5 Test sample . 8 6 Procedure 8 7 Calcula

21、tion 9 8 Test results . 11 Bibliography 12 Figure 1 Typical arrangement of the optical spectrum analyzer test apparatus for gain and power measurements . 6 BS EN 61290-1-1:2015IEC 61290-1-1:2015 IEC 2015 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ OPTICAL AMPLIFIERS TEST METHODS Part 1-1: Power an

22、d gain parameters Optical spectrum analyzer method FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation

23、 on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

24、 Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparati

25、on. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus

26、 of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are m

27、ade to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications trans

28、parently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent c

29、ertification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability

30、 shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including

31、 legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this

32、 publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61290-1-1 has been prepared by subcommittee 86C: F

33、ibre optic systems and active devices, of IEC technical committee 86: Fibre optics. This third edition cancels and replaces the second edition published in 2006 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous editio

34、n: a) updates on the characteristics of measurement apparatus; b) revised list of addressed optical amplifier parameters. BS EN 61290-1-1:2015 4 IEC 61290-1-1:2015 IEC 2015 The text of this standard is based on the following documents: FDIS Report on voting 86C/1309/FDIS 86C/1328/RVD Full informatio

35、n on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This standard shall be used in conjunction with IEC 61290-1 and IEC 61291-1. A list of all parts o

36、f the IEC 61290 series, published under the general title Optical amplifiers Test methods1can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the

37、data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date 1The first editions of some of these parts were published under the general title O

38、ptical fibre amplifiers Basic specification or Optical amplifier test methods. BS EN 61290-1-1:2015IEC 61290-1-1:2015 IEC 2015 5 OPTICAL AMPLIFIERS TEST METHODS Part 1-1: Power and gain parameters Optical spectrum analyzer method 1 Scope This part of IEC 61290 applies to all commercially available o

39、ptical amplifiers (OAs) and optically amplified modules. It applies to OAs using optically pumped fibres (OFAs based on either rare-earth doped fibres or on the Raman effect), semiconductor OAs (SOAs) and planar optical waveguide amplifiers (POWAs). The object of this standard is to establish unifor

40、m requirements for accurate and reliable measurements, by means of the optical spectrum analyzer test method, of the following OA parameters, as defined in IEC 61291-1: a) nominal output signal power; b) gain; c) polarization-dependent gain; d) maximum output signal power; e) maximum total output po

41、wer. NOTE All numerical values followed by () are suggested values for which the measurement is assured. The object of this standard is specifically directed to single-channel amplifiers. For multichannel amplifiers, one should refer to the IEC 61290-10 series 12. 2 Normative references The followin

42、g documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61290-1, Optica

43、l amplifiers - Test methods - Part 1: Power and gain parameters IEC 61291-1, Optical amplifiers - Part 1: Generic specification 3 Terms, definitions and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 61291-1 apply. 3.2 Abbreviations

44、ASE amplified spontaneous emission DBR distributed Bragg reflector (laser diode) DFB distributed feed-back (laser diode) 2Numbers in square brackets refer to the Bibliography BS EN 61290-1-1:2015 6 IEC 61290-1-1:2015 IEC 2015 ECL external cavity laser (diode) LED light emitting diode OA optical ampl

45、ifier OFA optical fibre amplifier POWA planar optical waveguide amplifier SOA semiconductor optical amplifier 4 Apparatus A diagram of the measurement set-up is given in Figure 1. Figure 1a Calibration Figure 1b Input signal power measurement Figure 1c Output power measurement Figure 1 Typical arran

46、gement of the optical spectrum analyzer test apparatus for gain and power measurements The test equipment listed below, with the required characteristics, is needed. a) optical source: The optical source shall be either at fixed wavelength or wavelength-tuneable. fixed-wavelength optical source: Thi

47、s optical source shall generate a light with a wavelength and optical power specified in the relevant detail specification. Unless otherwise specified, the optical source shall emit a continuous wave with the full width at half maximum of the spectrum narrower than 1 nm (). A distributed feed-back (

48、DFB) laser, a distributed Bragg reflector (DBR) laser, an external cavity laser (ECL) diode and a light emitting diode (LED) with a narrow-band filter are applicable, for example. The suppression ratio for the side modes for the DFB laser, the DBR laser or the ECL IEC Optical power meter Variable op

49、tical attenuator dB Optical source J1 Polarization controller (optional) IEC Optical spectrum analyzer Variable optical attenuator dB Optical source J1 J2 Polarization controller (optional) IEC OA under test Optical spectrum analyzer Variable optical attenuator dB Optical source J1 OA J2 Polarization controller (optional) BS EN 61290-1-1:2015IEC 61290-1-1:2015 IEC 2015 7 shall be higher than 30 dB (). The output power fluctuation shall be less t