BS EN 61212-3-2-2013 Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Specifications for individual materi.pdf

《BS EN 61212-3-2-2013 Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Specifications for individual materi.pdf》由会员分享，可在线阅读，更多相关《BS EN 61212-3-2-2013 Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Specifications for individual materi.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationInsulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposesPart 3: Specifications for individual materials Sheet 2: Round laminated moulded tubesBS EN 61212-3-2:2013National forewordThis British Standard is the U

2、K implementation of EN 61212-3-2:2013. It isidentical to IEC 61212-3-2:2013. It supersedes BS EN 61212-3-2:2006, whichwill be withdrawn on 3 June 2016.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/15, Solid electrical insulating materials, to SubcommitteeGEL/15/6, R

3、igid fibrous reinforced laminates for electrical purposes.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The Br

4、itish Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 70403 1ICS 29.035.01 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 Aug

5、ust 2013.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61212-3-2:2013EUROPEAN STANDARD EN 61212-3-2 NORME EUROPENNE EUROPISCHE NORM July 2013 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europi

6、sches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61212-3-2:2013 E ICS 29.035.01 Supersedes EN 61212-3-2:2006 English version Ins

7、ulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Round laminated moulded tubes (IEC 61212-3-2:2013) Matriaux isolants - Tubes et barres industriels rigides, ronds, st

8、ratifis, base de rsines thermodurcissables, usages lectriques - Partie 3: Spcifications pour matriaux particuliers - Feuille 2: Tubes ronds stratifis mouls (CEI 61212-3-2:2013) Isolierstoffe Runde Rohre und Stbe aus technischen Schichtpressstoffen auf der Basis warmhrtender Harze fr elektrotechnisch

9、e Zwecke Teil 3: Bestimmungen fr einzelne Werkstoffe Blatt 2: Runde, formgepresste Rohre (IEC 61212-3-2:2013) This European Standard was approved by CENELEC on 2013-06-03. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eur

10、opean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official ve

11、rsions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical c

12、ommittees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovaki

13、a, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61212-3-2:2013EN 61212-3-2:2013 - 2 - Foreword The text of document 15/700/FDIS, future edition 3 of IEC 61212-3-2, prepared by IEC/TC 15 “Solid electrical insulating materials“, was submitted to the IEC-CENELEC parallel v

14、ote and approved by CENELEC as EN 61212-3-2:2013. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-03-03 latest date by which the national standards conflicting with

15、the document have to be withdrawn (dow) 2016-06-03 This document supersedes EN 61212-3-2:2006. EN 61212-3-2:2013 includes the following significant technical changes with respect to EN 61212-3-2:2006: Details of test for insulation resistance after immersion in water are changed. Attention is drawn

16、to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61212-3-2:2013 was approved by CENELEC as a

17、 European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61212-3 series ISO 472:1999 NOTE Harmonized in EN 61212-3 series (not modified). NOTE Harmonized as EN ISO 472:2001 (not modified). BS EN 6121

18、2-3-2:2013- 3 - EN 61212-3-2:2013 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated refe

19、rences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title E

20、N/HD Year IEC 61212-1 - Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements EN 61212-1 - IEC 61212-2 2006 Insulating materials - Industrial rigid round laminated tube

21、s and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test EN 61212-2 2006 BS EN 61212-3-2:2013 2 61212-3-2 IEC:2013 CONTENTS INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 6 4 Designations and abbreviations 7 4.1 General . 7 4.2 Des

22、ignation . 7 4.3 Abbreviations 7 5 Requirements . 7 Bibliography 13 Table 1 Types of industrial round moulded tubes . 8 Table 2 Permissible deviation from nominal external diameter of round moulded tubes in the “as moulded“ condition 8 Table 3 Permissible deviation from nominal external diameter of

23、moulded tubes in ground or turned condition, all types . 9 Table 4 Permissible deviation from nominal internal diameter of moulded tubes 9 Table 5 Tolerance on wall thickness for round moulded tubes 9 Table 6 Departure from straightness for round moulded tubes . 10 Table 7 Property requirements for

24、round moulded tubes 11 Table 8 Electric strength at 90 C in oil, perpendicular to laminations for round moulded tubes (1 min proof test or 20 s step-by-step test)a(kV/mm) . 12 BS EN 61212-3-2:201361212-3-2 IEC:2013 5 INTRODUCTION This part of IEC 61212 is one of a series which deals with industrial

25、rigid round laminated tubes and rods based on thermosetting resins for electrical purposes. This series consists of three parts: Part 1: Definitions, designations and general requirements (IEC 61212-1) Part 2: Methods of test (IEC 61212-2) Part 3: Specifications for individual materials (IEC 61212-3

26、) IEC 61212-3-2 contains one of the specification sheets comprising Part 3, as follows: Sheet 2: Round laminated moulded tubes. BS EN 61212-3-2:2013 6 61212-3-2 IEC:2013 INSULATING MATERIALS INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES Part 3:

27、 Specifications for individual materials Sheet 2: Round laminated moulded tubes 1 Scope This part of IEC 61212 gives requirements for industrial rigid round laminated moulded tubes for electrical purposes, based on different resins and different reinforcements. Applications and distinguishing proper

28、ties are given in Table 1. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based o

29、n this specification alone. Safety Warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document an

30、d are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61212-1, Insulating materials Industrial rigid round laminated tubes and rods based on thermose

31、tting resins for electrical purposes Part 1: Definitions, designations and general requirements IEC 61212-2:2006, Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 2: Methods of test 3 Terms and definitions For the purpose

32、s of this document, the following term and definition apply. 3.1 moulded tube tube formed by rolling impregnated layers of material on a mandrel, curing the assembly in a cylindrical mould under heat and pressure, and then removing the mandrel SOURCE: ISO 472:1999, modified In the ISO definition, th

33、e term “laminated moulded tube” is used instead of “moulded tube” and an indication “or other suitable” is provided between the words “cylindrical” and “mould”. BS EN 61212-3-2:201361212-3-2 IEC:2013 7 4 Designations and abbreviations 4.1 General The moulded tubes covered by this Part 3 sheet are cl

34、assified into types which differ in the resin and reinforcement used, the method of manufacture and their distinguishing properties. 4.2 Designation Individual types are designated by: a two-letter abbreviation denoting the resin; a second two-letter abbreviation, denoting the reinforcement; a seria

35、l number of two digits, the first digit denoting the form of the material, a “3” indicates moulded tubes, and, a second digit denoting sub-grades of the same type. The abbreviations are given in 4.3. The complete designation of the moulded tube is denoted by: description: moulded tube; number of the

36、 IEC standard: IEC 61212-3-2; designation of the individual type; dimensions (in millimetres) of the moulded tube: internal diameter external diameter length; a letter designating the finish on the external diameter of the moulded tube: “A“ designating moulded tubes in the “as produced“ condition; “

37、B“ designating moulded tubes in ground or turned condition. EXAMPLE Moulded tube, IEC 61212-3-2 EP CC 31 25 35 1 000-A. 4.3 Abbreviations Types of resin Types of reinforcement EP Epoxy (epoxide) CC Woven cotton cloth PF Phenolic CP Cellulosic paper 5 Requirements In addition to the general requireme

38、nts given in IEC 61212-1, the moulded tubes shall comply with the additional requirements given in Tables 2, 3, 4, 5, 6, 7, and 8, with the exception of the length of tube supplied, which shall be subject to agreement between buyer and seller. BS EN 61212-3-2:2013 8 61212-3-2 IEC:2013 Table 1 Types

39、of industrial round moulded tubes Resin Reinforce- ment Serial numberApplications and distinguishing characteristicsaEP CC 31 Mechanical, electrical and electronic applications. Good resistance to tracking. fine weaveb. PF CC 31 Mechanical and electrical applications. fine weaveb. 32 Similar to type

40、 PF CC 31, but of coarse weaveb. 33 Similar to type PF CC 31, but of very coarse weaveb. CP 31 Electrical and mechanical applications. Good electrical properties when exposed to normal relative humidity. 32 Similar to type PF CP 31, but with improved mechanical and electrical properties. aIt should

41、not be inferred from the contents of Table 1 that round laminated moulded tubes of any particular type are necessarily unsuitable for applications other than those listed for them, or that specific round laminated moulded tubes will be suitable for all applications within the wide description given.

42、 bFabric weaves of type CC reinforcements: Mass per unit area g/m2Thread count cm-1Very coarse weave 200 130 18 to 29 Fine weave 130 30 to 37 Very fine weave 125 37 These values are only for information. They are not to be considered as specification values. In general, the finer weave materials hav

43、e better machining characteristics. Table 2 Permissible deviation from nominal external diameter of round moulded tubes in the “as moulded“ condition Nominal external diameter D mm Maximum deviation, mm Type PF CP EP CC PF CC 3 3 500 0,08 0,1 0,15 0,2 0,3 0,3 0,4 0,5 0,6 0,7 0,75 0,8 1,0 - - - 0,3 0

44、,4 0,4 0,4 0,5 0,6 0,7 0,75 0,8 1,0 Test method: see 4.1 of IEC 61212-2:2006. NOTE A double dash “-“ signifies that there is no requirement. BS EN 61212-3-2:201361212-3-2 IEC:2013 9 Table 3 Permissible deviation from nominal external diameter of moulded tubes in ground or turned condition, all types

45、 Nominal external diameter D mm Maximum deviationa mm 25 25 125 0,15 0,25 0,30 0,35 0,45 0,50 Test method: see 4.2 of IEC 61212-2:2006. aIf a unilateral tolerance is agreed between purchaser and supplier, the tolerance may not be greater than twice the value given in the table.Table 4 Permissible de

46、viation from nominal internal diameter of moulded tubes Nominal internal diameter d mm Maximum deviationa mm 3 3 500 0,10b0,15 0,20 0,25 0,30 0,50 0,70 1,00 1,50 2,00 Test method: see 4.3 of IEC 61212-2:2006. aIf a unilateral tolerance is agreed between purchaser and supplier, the tolerance may not

47、be greater than twice the value given in the table. bApplicable to PF CP types only.Table 5 Tolerance on wall thickness for round moulded tubes Nominal wall thickness t mm Maximum deviation mm Types PF CP PF CP 32 EP CC PF CC 31 PF CC PF CC 33 PF CC 34 1,5 1,5 25,0 0,25 0,40 0,55 0,90 1,30 2,00 0,28

48、 0,45 0,60 1,00 1,40 2,00 0,40 0,60 0,85 1,35 1,90 2,70 Test method: see 4.4 of IEC 61212-2:2006. BS EN 61212-3-2:2013 10 61212-3-2 IEC:2013 Table 6 Departure from straightness for round moulded tubes Nominal external diameter D mm Maximum deviation mm D 8 8 L2D 8 6 L2Test method: see 4.5 of IEC 612

49、12-2:2006. The departure from straightness of any tube shall not exceed the appropriate limiting value given above, where L is the length of the tube in metres. BS EN 61212-3-2:201361212-3-2 IEC:2013 11 Table7Propertyrequirementsfor round mouldedtubesPropertyMethod ofTestIEC61212-2:2006(SubclauseNo.)UnitMaximumorminimumTypeRemarksEPCC 31PFCC 31PFCC 32PFCC33PFCP 31PFCP 32Flexuralst