BS EN 61169-37-2007 Radio-frequency connectors - Sectional specification for STWX8 R F connectors《射频连接器 STWX8 R F连接器用分规范》.pdf

《BS EN 61169-37-2007 Radio-frequency connectors - Sectional specification for STWX8 R F connectors《射频连接器 STWX8 R F连接器用分规范》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61169-37-2007 Radio-frequency connectors - Sectional specification for STWX8 R F connectors《射频连接器 STWX8 R F连接器用分规范》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58STWX8 R.F connectorsThe European Standard EN 61169-37:2007 has the status of a British StandardICS

2、33.120.30Radio-frequency connectors Part 37: Sectional specification for BRITISH STANDARDBS EN 61169-37:2007BS EN 61169-37:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2007 BSI 2007ISBN 978 0 580 50820 2Amendments issued since p

3、ublicationAmd. No. Date Commentsrequest to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis

4、British Standard was published by BSI. It is the UK implementation of EN 61169-37:2007. It is identical with IEC 61169-37:2007.The UK participation in its preparation was entrusted by Technical Committee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communicati

5、on and signalling, to Subcommittee EPL/46/2, Radio frequency connectors and waveguides.A list of organizations represented on this committee can be obtained on EUROPEAN STANDARD EN 61169-37 NORME EUROPENNE EUROPISCHE NORM April 2007 CENELEC European Committee for Electrotechnical Standardization Com

6、it Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61169-37:2007 E ICS 33.1

7、20.30 English version Radio-frequency connectors - Part 37: Sectional specification for STWX8 R.F connectors (IEC 61169-37:2007) Connecteurs pour frquences radiolectriques - Partie 37: Spcification intermdiaire relative aux connecteurs pour frquences radiolectriques de type STWX8 (CEI 61169-37:2007)

8、 Hochfrequenz-Steckverbinder - Teil 37: Rahmenspezifikationen - STWX8-Hochfrequenzsteckverbinder (IEC 61169-37:2007) This European Standard was approved by CENELEC on 2007-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

9、his European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versi

10、ons (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of

11、Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdo

12、m. Foreword The text of document 46F/44/CDV, future edition 1 of IEC 61169-37, prepared by SC 46F, R.F. and microwave passive components, of IEC TC 46, Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories, was submitted to the IEC-CENELEC parallel Unique

13、Acceptance Procedure and was approved by CENELEC as EN 61169-37 on 2007-03-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-12-01 latest date by which the national sta

14、ndards conflicting with the EN have to be withdrawn (dow) 2010-03-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61169-37:2007 was approved by CENELEC as a European Standard without any modification. _ 2 EN 61169-37:2007 3 CONTENTS 1 Scope.4 2

15、Normative references. 4 3 Mating face and gauge information.4 3.1 Dimensions - General connectors Grade 2 (Figure 1) .4 3.2 Gauges for general purpose connectors - Grade 2 6 3.3 Dimensions standard test connectors Grade 0.9 4 Quality assessment procedure12 4.1 General .12 4.2 Rating and characterist

16、ics (see Clause 6 of IEC 61169-1 (QC 220000) 124.3 Test schedule and inspection requirements - Acceptance tests .15 4.4 Procedures18 5 Instructions for preparation of detail specifications. 18 5.1 General .18 5.2 Identification of the detail specification 18 5.3 Identification of the component18 5.4

17、 Performance19 5.5 Marking, ordering information and related matters.19 5.6 Selection of tests, tests conditions and severities19 5.7 Blank detail specification pro-forma for type STWX 8 connectors 19 Figure 1 Mating face of STWX8 connectors (for dimensions and notes, see Table 1) .5 Figure 2 Gauge

18、pins for contact of socket connectors (for dimensions, see Table 2).7 Figure 3 Gauge for outer of socket connectors (for dimensions, see Table 3) 8 Figure 4 Female contact (for dimensions and notes, see Table 4)9 Figure 5 Male contact (for dimensions and notes, see Table 5)11 Table 1 Mating face dim

19、ensions.6 Table 2 Gauges Dimensions 7Table 3 Gauge dimensions 9 Table 4 Female contact dimensions .10 Table 5 Male contact dimensions .11 Table 6 Rating and characteristics .13 Table 7 Acceptance tests.15 Table 8 Periodic tests Annex ZA (normative) Normative references to international publications

20、with their corresponding European publications . EN 61169-37:20072516 4 RADIO-FREQUENCY CONNECTORS Part 37: Sectional specification STWX8 R.F. connectors 1 Scope This part of IEC 61169, which is a Sectional Specification (SS), provides information and rules for the preparation of Detail Specificatio

21、ns (DS) for type STWX8 R.F. coaxial connectors with push-pull self-lock coupling. The connectors are normally used with flexible and semi-rigid R.F. cables for middle power applications in conjunction with 50 cables in an operating frequency range up to 4 GHz. It describes the interface dimensions f

22、or general purpose grade 2 connectors, dimensional details for standard test connectors, grade 0, together with gauging information and the mandatory tests selected from QC 220000 (IEC 61169-1), applicable to all DS relating to type STWX8 connectors. This specification indicates the recommended perf

23、ormance characteristics to be considered when writing a DS and covers test schedules and inspection requirements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refere

24、nces, the latest edition of the referenced document (including any amendments) applies. IEC 60096 (all parts), Radio-frequency cables IEC 61169-1:1992, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods Amendment 1 (1996) Amendment 2 (1997) 3 Mating f

25、ace and gauge information 3.1 Dimensions - General connectors Grade 2 (Figure 1) All dimensions are in mm. All un-dimensioned pictorial configurations are for reference purpose only. EN 61169-37:2007 5 Note 1JD F H C B A G E N P Note 1 Note 1Note 1U S I T X C Z W K 90 10 L MBB Q EE Q M M A L MCC DD

26、AA Note 1 Note 4 V Q RIEC 300/07 Figure 1 Mating face of STWX8 connectors (for dimensions and notes, see Table 1) EN 61169-37:2007 6 Table 1 Mating face dimensions mm Reference min. max. Notes A 8,12 8,20 Diameter B 4,83, - Diameter C 2,06 2,21 Diameter D 4,0 - E 5,33 5,84 F - 0,18 G 4,5 - H - 0,18

27、I 8,22 8,28 Diameter J 6,90 7,00 K - 2,20 L 0,05 0,15 Radius M - 0,13 RadiusN - 0,64 Diameter P 1,32 1,37 Diameter Q 0,19 0,25 R 0,00 0,30 S 7,05 - T - - Diameter (see Note 2) U 7,05 - V 6,00 - W 0,18 - X - 4,72- Diameter Z 0,18 - AA - - Diameter (see Note 3) BB 7,92 8,02 Diameter CC 1,22 1,42 DD 0,

28、72 0,92 EE 1,10 Nominal NOTE 1 Reference plane: mechanical and electrical. NOTE 2 To meet electrical and mechanical requirements. NOTE 3 Bore diameter closed to meet electrical and mechanical requirements when mated with a 1,32/1,37 diameter. 3.2 Gauges for general purpose connectors - Grade 2 All d

29、imensions are in mm. All undimensioned pictorial configurations are for reference purposes only. EN 61169-37:2007 7 3.2.1 Gauges for socket contact 4 mm (max.)3,17 mm (min.)5010D C IEC 301/07 Figure 2 Gauge pins for contact of socket connectors (for dimensions, see Table 2) Table 2 Gauges Dimensions

30、 Gauge A- Maximum material for sizing purposes Gauge B Minimum material for measurement of gauge retention force Mass of gauge: (80 1) g mm mmReference min. max. min. max. D 1,370 1,375 1,315 1,320 C 0 0,64 - - Material: steel, polished. Surface roughness: Ra=0,4 m maximum. Test procedure According

31、to 9.3.4 of IEC 61169-1, the gauge A shall be inserted three times into the socket center contact. This is a sizing operation. After this, the gauge B shall be inserted into socket centre contact. The contact shall support the mass of the gauge in a vertical downward attitude. NOTE The minimum diame

32、ter of gauge A corresponds to the maximum diameter of a male contact. EN 61169-37:2007 8 3.2.2 Gauges for female outer contact Radius or allow chamfer 0,38 mm (max.) Jack connector center contact/insulator into the holeA J Reference plane IEC 302/07 (A) General dimensions Q M MA90 10 Reference plane

33、 Reference planeL M QBBK L M DD QCC IEC 303/07 (B) Alternative coupling grooves Figure 3 Gauge for outer of socket connectors (for dimensions, see Table 3) EN 61169-37:2007 9 Table 3 Gauge dimensions Gauge C-Maximum material for sizing purpose Gauge D-Minimum material for measurement of gauge retent

34、ion force mm mmReference min. max. min. max. A 8,185 8,20 8,12 8,135 J 7,05 7,15 7,05 7,15 K 1,1 1,1 Rad.L 0,05 0,15 0,05 0,15 RadM - 0,13 - 0,13 Q 0,2 0,25 0,15 0,20 BB 7,95 7,98 7,95 7,98 CC 1,2 1,4 1,1 1,3 DD 0,6 0,8 0,5 0,7 Material: polished steel. Surface roughness: Ra =0,4 m max. Test procedu

35、re According to 9.3.4 of IEC 61169-1, the gauge C shall be placed three times inside the outer contact. This is a sizing operation. The gauge D is placed inside the outer contact.The retention force of the gauge shall be 15 N minimum. 3.3 Dimensions standard test connectors Grade 0 3.3.1 Socket (fem

36、ale contact) Note 1J R D B Q A F H V C P Y Z Note 1 H EXWIEC 304/07 Figure 4 Female contact (for dimensions and notes, see Table 4) EN 61169-37:2007 10 Table 4 Female contact dimensions mm Reference min. max. Notes A 8,22 8,25 Diameter B 4,67 4,72 see Note 3/Diameter C 2,16 2,18 see Note 4/Diameter

37、D see Note 2/Diameter E 6 F 0,27 0,52 H 0,29 0,57 J 7,05 7,20 P 1,39 1,41 Diameter Q 7,78 7,82 R 0 0,30 V 2,13 2,18 Diameter W 4,62 4,88 X 6,05 6,10 Y 0,18 0,23 Z 0,15 0,25 NOTE 1 Reference plane: mechanical and electrical. NOTE 2 Diameter of outer conductor and length of uniform section of transmis

38、sion line to give required characteristic impedance of 50 when checked using time domain reflectometer methods. NOTE 3 Dimension for use of PTFE dielectric having a dielectric constant of 2,02. Use of PTFE is mandatory. NOTE 4 Bore diameter closed to meet electrical and mechanical requirements when

39、mated with a 1,35/1,37 diameter. EN 61169-37:2007 11 3.3.2 Plug (male contact) Note 1j f h r b a c d u Note 160 1e n p IEC 305/07Figure 5 Male contact (for dimensions and notes, see Table 5) Table 5 Male contact dimensions mm Reference min. max. Notes a 8,15 8,20 Diameter b 4,88 4,93 see Note 3/Diam

40、eter c 2,13 2,18 see Note 2/Diameter d see Note 2/Diameter e f 0,04 0,24 h 0,09 j 6,95 7,00 n 0,30 p 1,35 1,37 Diameter r 0 0,20 Diameter u 0,10 0,20 NOTE 1 Reference plane: mechanical and electrical. NOTE 2 Diameter of outer conductor and length of uniform section of transmission line to give requi

41、red characteristic impedance of 50 when checked using time domain reflectometer methods. NOTE 3 Dimension for use of PTFE dielectric having a dielectric constant of 2,02. Use of PTFE is mandatory. EN 61169-37:2007 12 4 Quality assessment procedure 4.1 General The following subclauses provide recomme

42、nded rating, performance and test conditions to be considered when writing a Detail Specification (DS). They also provide an appropriate schedule of tests with the pro-formal blank detail specification and instructions for the preparation of a detail specification. 4.2 Rating and characteristics (se

43、e Clause 6 of IEC 61169-1 (QC 220000) The values indicated below are recommended for Type STWX8 connectors and are given for the writer of the detail specification (see Table 6). They are applicable to the condition when the connectors are fully mated. Certain tests will usually not be required. Whe

44、n these tests are required appropriate values shall be entered in the detail specification at the discretion of the specification writer. EN 61169-37:2007 13 Table 6 Rating and characteristics Rating and characteristics Test method IEC 61169-1 (QC 220000) Subclause Value Remarks deviations form stan

45、dard test method Electrical Nominal impedance Frequency range Grade 2 connectors -flexible cable,straight styles -semi-rigid cable straight styles -right -angle styles Reflection factor 1)Grade 2 connectors -flexible cable straight styles -flexible cable right angle styles -semi-rigid cable straight

46、 styles -semi-rigid cable right angle styles -component mounting styles -solder bucket and PCB mounting styles Center contact resistance2)-initial -after conditioning Outer conductor continuity2)-initial -after conditioning Insulation resistance2)-initial -after conditioning Proof voltage at sea lev

47、el 3)4)-cable 96IEC-50-3-1,IEC 50-3-7 -cable 96IEC50-5-1,IEC50-5-2 -semi-rigid 3,58 mm diameter -semi-rigid 6,35 mm diameter Proof voltage at 4,4 kPa 3)4)-cables 96IE50-3-1, IEC50-3-7 -cables 96IEC50-5-1, IEC50-5-2 -semi-rigid 3,58 mm diameter -semi-rigid 6,35 mm diameter Environmental test voltage

48、at sea level3)4)-cables 96IEC50-3-1, IEC50-3-7 -cables 96 IEC50-5-1, IEC50-5-2 -semi-rigid 3,58 mm diameter -semi-rigid 6,35 mm diameter Environmental test voltage at 4,4 kPa3)4)-cables 96IE50-3-1, IEC50-3-7 -cables 96IEC50-5-1, IEC50-5-2 -semi-rigid 3,58 mm diameter -semi-rigid 6,35 mm diameter Screening effectiveness (cable connector only)7)Discharge test (corona) 9.2.1 9.2.3 9.2.3 9.2.5 9.2.6 9.2.6 9.2.6 9.2.6 9.2.8 50 up to 4 GHz up to 4 GHz up to 4 GHz 0,11+0,02f 0,15+0,03f 0,11+0,01f 0,15+0,02f see detail specification 0,2 m 3,0 m 1,0 m