BS EN 61169-29-2005 Radio-frequency connectors - Sectional specification - Miniature radio frequency coaxial connectors model screw snap-on push-pull or quick-lock slide-in (rack ac.pdf

《BS EN 61169-29-2005 Radio-frequency connectors - Sectional specification - Miniature radio frequency coaxial connectors model screw snap-on push-pull or quick-lock slide-in (rack ac.pdf》由会员分享，可在线阅读，更多相关《BS EN 61169-29-2005 Radio-frequency connectors - Sectional specification - Miniature radio frequency coaxial connectors model screw snap-on push-pull or quick-lock slide-in (rack ac.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61169-29:2005 Radio-frequency connectors Part 29: Sectional specification Miniature radio frequency coaxial connectors model screw, snap-on, push-pull or quick-lock, slide-in (rack and panel applications) Characteristic impedance 50 ohms (type 1,0/2,3) 50 ohms and 75 ohms appl

2、ications The European Standard EN 61169-29:2005 has the status of a British Standard ICS 33.120.30BS EN 61169-29:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 9 November 2005 BSI 9 November 2005 ISBN 0 580 46743 0 National foreword Thi

3、s British Standard is the official English language version of EN 61169-29:2005. It is identical with IEC 61169-29:2005. The UK participation in its preparation was entrusted by Technical Committee waveguides, which has the responsibility to: A list of organizations represented on this subcommittee

4、can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search

5、” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obli

6、gations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of p

7、ages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 28, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments EPL/

8、46, Cables, wires and waveguides, RF connectors and accessories for communication and signalling, to Subcommittee EPL/46/2, RF connectors and EUROPEAN STANDARD EN 61169-29 NORME EUROPENNE EUROPISCHE NORM September 2005 CENELEC European Committee for Electrotechnical Standardization Comit Europen de

9、Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61169-29:2005 E ICS 33.120.30 English

10、version Radio-frequency connectors Part 29: Sectional specification Miniature radio frequency coaxial connectors model screw, snap-on, push-pull or quick-lock, slide-in (rack and panel applications) Characteristic impedance 50 ohms (type 1,0/2,3) 50 ohms and 75 ohms applications (IEC 61169-29:2005)

11、Connecteurs pour frquences radiolectriques Partie 29: Spcification intermdiaire Connecteurs coaxiaux miniatures pour frquences radiolectriques avec accouplements de type vis, pousser-tirer et encliquetage, ou glis (applications de “panneau“ et “fond de panier“) Impdance caractristique 50 ohms (type

12、1,0/2,3) Applications 50 ohms et 75 ohms (CEI 61169-29:2005) Hochfrequenz-Steckverbinder Teil 29: Rahmenspezifikation Koaxiale Miniatur-Hochfrequenzsteckverbinder mit Schraub-, Einrast-, Push-pull- oder Schnellverschluss-, Einschubkupplung (Einschubausfhrung) Wellenwiderstand 50-Ohm (Typ 1,0/2,3) 50

13、-Ohm- und 75-Ohm-Anwendungen (IEC 61169-29:2005) This European Standard was approved by CENELEC on 2005-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any

14、alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made

15、by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland,

16、 France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 61169-29:2005 2 Foreword The text of document 46F/27/FDIS, future edition 1 of IEC 61169-29,

17、prepared by SC 46F, R.F. and microwave passive components, of IEC TC 46, Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories, was submitted to IEC-CENELEC parallel vote and was approved by CENELEC as EN 61169-29 on 2005-07-01. The following dates were fi

18、xed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2008-07-01 Annex ZA has been added by CENELEC. _

19、 Endorsement notice The text of the International Standard IEC 61169-29:2005 was approved by CENELEC as a European Standard without any modification. _ 3 EN 61169-29:2005 CONTENTS 1 Scope 4 2 Normative references .4 3 IEC type designation 5 4 Interface information.6 5 Quality assessment procedures 1

20、4 6 Instructions for preparation of detail specifications 21 Annex ZA (normative) Normative references to international publications with their corresponding European Publications .28 Figure 1 Interfaces (for dimensions, see Table 1) .6 Figure 2 Locking devices (for dimensions, see Table 2) 8 Figure

21、 3 Gauge pin for centre contact of socket connector10 Figure 4 Outer contact sizing and retention force gauges A and B.11 Figure 5 Plug.12 Figure 6 Socket .13 Table 1 Dimensions of the interfaces7 Table 2 Dimensions of the locking devices .9 EN 61169-29:2005 4 RADIO-FREQUENCY CONNECTORS Part 29: Sec

22、tional specification Miniature radio frequency coaxial connectors model screw, snap-on, push-pull or quick-lock, slide-in (rack and panel applications) Characterisctic impedance 50 (type 1,0/2,3) 50 and 75 applications 1 Scope This part of IEC 61169, which is a sectional specification (SS), provides

23、 information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with screw, snap- on, push-pull or quick-lock, slide-in coupling (rack and panel applications) with a characterisctic impedance of 50 (type 1,0/2,3) for 50 and 75 applications. The connectors are norma

24、lly used with flexible and semi-rigid r.f. cables for low power applications in conjunction with 50 cables in an operating frequency range up to 10 GHz or in conjunction with 75 cables up to 2 GHz. It describes the interface dimensions for general purpose grade 2 connectors, dimensional details for

25、standard test connectors, grade 0, together with gauging information and the mandatory tests selected from IEC 61169-1, applicable to all DS relating to type 1,0/2,3 connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers tes

26、t schedules and inspection requirements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendm

27、ents) applies. IEC 61169-1:1992, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods 5 EN 61169-29:2005 3 IEC type designation Type designations are given for each of the various coupling mechanisms: Screw the coupling mechanism consists of a coupling

28、nut (on the plug ) and a thread (on the socket). The tightening torque is achieved by hand. The engagement and separation force depends on the mechanical dimensions of the inner and outer contacts of the plug and socket. Snap on the coupling mechanism consists of a spring device (on the plug) that f

29、its in a suitable shape of the body (on the socket). The engagement and separation force depends on the mechanical dimensions of the inner and outer contact, of the spring device and of the socket body. The coupling mechanism does not prevent accidental disengagements. Push pull or Quick lock (herea

30、fter called push pull) the coupling mechanism consists of a spring device (on the plug) that fits in a suitable shape of the body (on the socket). The engagement and separation force depends on the mechanical dimensions of the inner and outer contact, of the spring element and of the socket body. Th

31、is coupling mechanism prevents accidental disengagements. Slide in the coupling mechanism consists of a nut (on the plug) which allows a float mounting on the panel preventing a radial misalignment. The engagement and separation force depends on the mechanical dimensions of the inner and outer conta

32、cts of the plug and socket. In case of rack and panel applications, the separation range of panels may differ from the fully mated position by 1,7 mm. Connectors conforming to this part of IEC 61169 shall be designated by: a) the reference to this part of IEC 61169: IEC 61169-29; b) the grade number

33、: Grade 0 = standard test connector = G0 Grade 2 = general purpose connector = G2 c) identification number (see Clause 8 of IEC 61169-1). EN 61169-29:2005 6 4 Interface information 4.1 Dimensions 4.1.1 General purpose connectors - Grade 2 Millimetre dimensions are original dimensions. All undimensio

34、ned pictorial configurations are for reference purposes only. Plug Pin contact Flared to meet the gauging requirement Reference plane electrical and mechanical Radius 0,8 0,1 (0,030 0,002) Socket Radius 0,3 max. (0,010 max.) Slotted and closed to meet the gauging requirement Socket resilient contact

35、 S F B A C D E 30 2 K G H R L I M N T O P IEC 820/05 Figure 1 Interfaces (for dimensions, see Table 1) 7 EN 61169-29:2005 Table 1 Dimensions of the interfaces mm in Ref. Min. Max. Min. Max. Note A 0,475 0,520 0,018 7 0,020 5 Diameter B 4,5 0,177 C 5,5 0,217 D 1,15 0,045 E (*) 1 nominal 0,039 nominal

36、 Diameter F 5,4 5,7 0,213 0,224 G 3,00 3,06 0,118 0,120 Diameter H 4,03 4,14 0,159 0,163 Diameter I 1,8 1,9 0,071 0,075 K M 5,5 0,5 L 0,5 0,6 0,020 0,024 M 5,8 5,9 0,228 0,232 N 6,4 6,5 0,252 0,256 O (*) 1 nominal 0,039 nominal Diameter P 1,15 1,75 0,045 0,069 R 3,525 3,600 0,138 8 0,141 7 Diameter

37、S 2,3 nominal 0,091 nominal Diameter T 4,5 0,177 (*) = only for 50 version. EN 61169-29:2005 8 Figure 2 Locking devices (for dimensions, see Table 2) G F F S U T C E A D B M H L* I K R 45 2 P O Figure 2a Screw Reference plane Biased in the forward direction Reference plane 45 2 Biased in the forward

38、 direction Figure 2b Snap-on Figure 2b(bis) Push-pull Figure 2c Slide-in (rack and panel applications) * Separation of panels when fully mated IEC 821/05 9 EN 61169-29:2005 Table 2 Dimensions of the locking devices mm in Ref. Min. Max. Min. Max. Note A 6,44 6,50 0,254 0,256 Diameter B 8,55 8,9 0,337

39、 0,350 C 13,3 13,5 0,524 0,531 D 2,7 3,9 0,106 0,154 E M 5,5 0,5 Thread F 1,95 2,05 0,077 0,081 G 6,4 0,252 H 8,25 8,40 0,325 0,331 I 7,5 7,6 0,295 0,299 K 3,10 3,15 0,122 0,124 L 11,9 13,6 0,469 0,535 M 4,8 4,9 0,189 0,193 O 7,3 0,287 Diameter P 4,2 4,26 0,165 0,168 Diameter R 1,4 1,6 0,055 0,063 S

40、 6,1 0,240 T 7,9 0,311 Diameter U 7,6 0,299 EN 61169-29:2005 10 4.2 Gauges 4.2.1 Gauges for general purpose connectors Millimetre dimensions are original dimensions. All undimensioned pictorial configurations are for reference purposes only. 4.2.1.1 Gauge for socket centre contact 25 5 a 2,0 min. (0

41、,079 min.) IEC 822/05 NOTE Dimensions are in millimetres. Figures in brackets represent inches. Gauge A Maximum material for sizing purposes Gauge B Minimum material for measurement of gauge retention force Mass (weight) of gauge (20 1) g mm in mm in Ref. Min. Max. Min. Max. Min. Max. Min. Max. a 0,

42、516 0,520 0,020 3 0,020 5 0,471 0,475 0,081 5 0,018 7 Material: steel, polished Surface roughness Ra: 0,4 m (16 in) max. Figure 3 Gauge pin for centre contact of socket connector Test procedure: Gauge A shall be inserted once only into the socket centre contact. This is a sizing operation. After thi

43、s, gauge B shall be inserted into the socket centre contact. The contact shall support the mass of the gauge in a vertical downward attitude. NOTE Gauge A is used for qualification approval tests only (see 9.3.4 of IEC 61169-1). The maximum diameter of gauge A corresponds to the maximum diameter of

44、a pin contact. 11 EN 61169-29:2005 4.2.1.2 Gauge for outer contact of plug connector Radius 0,2 0,05 (0,008 0,002) Radius 0,3 0,05 (0,012 0,002) 30 2 a A C B* D IEC 823/05 NOTE Dimensions are in millimetres. Figures in brackets represent inches. * Surface roughness to apply on this length of inside

45、surface ( 1). mm in Ref. Min. Max. Min. Max. Note A 4,1 0,161 Diameter B 7 nominal 0,276 C 9 0,354 D 0,5 0,6 0,020 0,024 Gauge A Maxumum material for sizing purposes Gauge B Minimum material for measurement of gauge retention force Mass (weight) of gauge (70 1) g mm in mm in Ref. Min. Max. Min. Max.

46、 Min. Max. Min. Max. a 3,000 3,006 0,118 1 0,118 3 3,060 3,068 0,120 5 0,120 8 Material: steel, polished Surface roughness Ra: 0,4 m (16 in) max. Figure 4 Outer contact sizing and retention force gauges A and B Test procedure: The resilient plug outer conductor shall be inserted once only into gauge

47、 A. This is a sizing operation. After this, the resilient plug outer conductor shall be inserted into gauge B. The conductor shall support the mass of the gauge in a vertical downward attitude. EN 61169-29:2005 12 4.2.2 Dimensions Standard test connectors Grade 0 Millimetre dimensions are original d

48、imensions. All undimensioned pictorial configurations are for reference purposes only. Pin contact A BC F E D G H I 45 2 Reference plane mechanical and electrical IEC 824/05 mm in Ref. Min. Max. Min. Max. Note A 2,99 3,00 0,117 7 0,118 1 Diameter B 2,30 2,31 0,090 6 0,090 9 Diameter C 5,40 5,70 0,213 0,224 D 0,50 0,52 0,020 1 0,020 5 Diameter E 0,30 0,40 0,012 0,016 F 4,50 0,177 G 5,30 5,50 0,209 0,217 H 0,95 1,15 0,037 0,045 I 0,99 1,00 0,039 0,039 4 Diameter Figure 5 Plug 13 EN 61169-29:2005 Radius 0,8 0,05 (0,031 0,002) 30 2 Radius 0,3 max. (0,010 max.) Socket resilient