BS EN 61169-18-2011 Radio-frequency connectors Sectional specification Radio frequency coaxial connectors of type SSMA《射频连接器 分规范 扩频多址(SSMA)型射频同轴连接器》.pdf

《BS EN 61169-18-2011 Radio-frequency connectors Sectional specification Radio frequency coaxial connectors of type SSMA《射频连接器 分规范 扩频多址(SSMA)型射频同轴连接器》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61169-18-2011 Radio-frequency connectors Sectional specification Radio frequency coaxial connectors of type SSMA《射频连接器 分规范 扩频多址(SSMA)型射频同轴连接器》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationRadio-frequency connectorsPart 18: Sectional specification Radio frequency coaxial connectors of type SSMABS EN 61169-18:2011National forewordThis British Standard is the UK impl

2、ementation of EN 61169-18:2011. It is identical to IEC 61169-18:2011. It supersedes DD IEC/PAS 61169-18:2009 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee EPL/46, Cables, wires and waveguides, radio frequency connectors and acces sories for communica

3、tion and signalling.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 64918 9 ICS 33.120

4、.30Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2011.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 61169-18:2011

5、EUROPEAN STANDARD EN 61169-18 NORME EUROPENNE EUROPISCHE NORM March 2011 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELE

6、C - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61169-18:2011 E ICS 33.120.30 English version Radio-frequency connectors - Part 18: Sectional specification - Radio frequency coaxial connectors of type SSMA (IEC 61169-18:2011) Connecteur

7、s pour frquences radiolectriques - Partie 18: Spcification intermdiaire - Connecteurs coaxiaux pour frquences radiolectriques de type SSMA (CEI 61169-18:2011) Hochfrequenz-Steckverbinder - Teil 18: Rahmenspezifikation - Hochfrequenz-Koaxial-Steckverbinder des Typs SSMA (IEC 61169-18:2011) This Europ

8、ean Standard was approved by CENELEC on 2011-03-03. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

9、 concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member

10、 into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I

11、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 61169-18:2011EN 61169-18:2011 - 2 - Foreword The text of document 46F/136/CDV, future edition 1 of IEC 61169-

12、18, prepared by SC 46F, R.F. and microwave passive components, of IEC TC 46, Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61169-18 on 2011-03-03. Attention is drawn

13、to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publi

14、cation of an identical national standard or by endorsement (dop) 2011-12-03 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2014-03-03 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61169-18:2011 was

15、approved by CENELEC as a European Standard without any modification. _ BS EN 61169-18:2011- 3 - EN 61169-18:2011 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the applica

16、tion of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN

17、/HD applies. Publication Year Title EN/HD Year IEC 61169-1 A1 A2 1992 1996 1997 Radio-frequency connectors - Part 1: Generic specification - General requirements and measuring methods EN 61169-1 A1 A2 1994 1996 1997 BS EN 61169-18:2011 2 61169-18 IEC:2011 CONTENTS 1 Scope . 6 2 Normative references

18、. 6 3 Mating face and gauge information . 6 3.1 Dimensions - High performance connectors Grade 1 6 3.1.1 Connector with pin-centre contact 7 3.1.2 Connector with socket-centre contact 8 3.2 Gauges . 9 3.2.1 Gauge pins for socket-centre contact . 9 3.2.2 Test procedure 9 3.3 Dimensions - standard tes

19、t connectors Grade 0 . 10 3.3.1 Connector with pin-centre contact 10 3.3.2 Connector with socket-centre contact 11 4 Quality assessment procedure 12 4.1 General . 12 4.2 Standard ratings and characteristics (see Clause 6 of IEC 61169-1) 12 4.3 Test schedule and inspection requirements Acceptance tes

20、ts . 15 4.3.1 Acceptance tests . 15 4.3.2 Periodic tests 15 4.4 Procedures 18 4.4.1 Quality conformance inspection . 18 4.4.2 Qualification approval and its maintenance 18 5 Instructions for preparation of detail specifications . 18 5.1 General . 18 5.2 Identification of the component 18 5.3 Perform

21、ance 19 5.4 Marking, ordering information and related matters . 19 5.5 Selection of tests, test conditions and severities 19 5.6 Blank detail specification pro-forma for type SSMA connector . 20 Figure 1 Connector with pin-centre contact (for dimensions and notes, see Table 1) 7 Figure 2 Connector w

22、ith socket-centre contact (for dimensions and notes, see Table 2) 8 Figure 3 Gauge pins for socket-centre contact (for dimensions and notes, see Table 3) 9 Figure 4 Connector with pin-centre contact (for dimensions and notes, see Table 4) 10 Figure 5 Connector with socket-centre contact (for dimensi

23、ons and notes, see Table 5) 11 BS EN 61169-18:201161169-18 IEC:2011 3 Table 1 Dimensions of connector with pin-centre contact . 7 Table 2 Dimensions of connector with socket-centre contact 8 Table 3 Dimensions of gauge pins for socket-centre contact 9 Table 4 Dimensions of connector with pin-centre

24、contact . 10 Table 5 Dimensions of connector with socket-centre contact 12 Table 6 Rating and characteristics . 13 Table 7 Acceptance tests . 15 Table 8 Periodic tests 16 BS EN 61169-18:2011 6 61169-18 IEC:2011 RADIO-FREQUENCY CONNECTORS Part 18: Sectional specification Radio frequency coaxial conne

25、ctors of type SSMA 1 Scope SSMA series connectors with characteristic impedance 50 are used for millimeter wave applications, connecting with RF cables or micro strips. The operating frequency limit is up to 35 GHz. The coupling thread is 10-36 UNS thread. This sectional specification provides infor

26、mation and rules for preparation of detail specification of SSMA series R.F connectors together with the pro-forma blank detail specification. It also prescribes mating face dimensions for grade 1 high performance connectors, dimensional detail of grade 0 standard test connectors, gauging informatio

27、n and tests selected from IEC 61169-1 applicable to all detail specifications relating to SSMA series RF connectors. This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for

28、assessment levels M and H. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

29、 IEC 61169-1:19981992, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods1Amendment 1 (1996) Amendment 2 (1997) 3 Mating face and gauge information 3.1 Dimensions High performance connectors Grade 1 All undimensioned pictorial configurations are for r

30、eference purpose only. _ 1There exists a consolidated edition 1.2 (1998) that comprises IEC 61169-1:1992, its Amendment 1:1996 and its Amendment 2:1997. BS EN 61169-18:201161169-18 IEC:2011 7 3.1.1 Connector with pin-centre contact Not e 110-36UNS-2B10-36UNS-2B(Chamf er )Gas k et ( Not e 4)(Not e 2)

31、Not e 3El ect r i cal and Me c h a n i c a l r e f e r e n c eElectrical and mechani al referenceGasket (Note 4)Note 1gicfelnd (Note 2)bha10-36UNS-2Bjm(Cha fer)Note3IEC 053/11Figure 1 Connector with pin-centre contact (for dimensions and notes, see Table 1) Table 1 Dimensions of connector with pin-c

32、entre contact Ref. mm Min. Max. a 4,98 - b 3,15 3,22 c 0,38 1,14 d - 3,43 e 2,54 - f 0,00 0,18 g 0,00 0,25 h 2,79 nominal i 0,08 max. 45 or R0,08 max. j 0,495 0,528 l 1,00 - m - 0,25 n - 1,65 BS EN 61169-18:2011 8 61169-18 IEC:2011 NOTE 1 Dimensions are such that the reference planes coincide and th

33、e connectors meet the required environmental performance. NOTE 2 Dimension for coupling nut to screw forward. NOTE 3 The diameters are chosen upon the assumption that the PTFE dielectric has a dielectric constant of 2,02 to give an impedance of 50 . NOTE 4 For grade 1 connectors, the design of which

34、 is free, the sealing gasket is mandatory. 3.1.2 Connector with socket-centre contact I10-36UNS-2AI(Not e 3)Not e 2 Not e 1No f i l l et per mi t t edRoot c ut ac c ept abl eEl ect r i cal and Me c h a n i c a l r e f e r e n c eElectrical and mechanical referencey (Note 3)vu10-36UNS-2ANote2wopIINo

35、fillet permittedcut acceptablextsrqzNote1IEC 054/11Figure 2 Connector with socket-centre contact (for dimensions and notes, see Table 2) Table 2 Dimensions of connector with socket-centre contact Ref. mm Min. Max. o 3,91 - p4,32 - q0,00 0,25 r1,88 1,98 s 0,00 0,18 t 0,38 1,14 u2,79 nominal v3,231 3,

36、300 w3,89 4,06 BS EN 61169-18:201161169-18 IEC:2011 9 Ref. mm Min. Max. x45 y 0,25 - z2,92 - NOTE 1 Resilient contact may be closed or open entry, method of resilience is optional. NOTE 2 The diameters are chosen upon the assumption that the PTFE dielectric has a dielectric constant of 2,02 to give

37、an impedance of 50 . NOTE 3 y refers to the width of the end surface platform. 3.2 Gauges 3.2.1 Gauge pins for socket-centre contact Blend radiusR 0,4 mm max.50 2a0,2 mm max.bIEC 055/11Figure 3 Gauge pins for socket-centre contact (for dimensions and notes, see Table 3) Table 3 Dimensions of gauge p

38、ins for socket-centre contact Gauge A Maximum material for sizing purposes Gauge B Minimum material for measurement of retention force Ref. mm mm Min. Max. Min. Max. a 0,528 0,533 0,492 0,495 b 1,25 1,35 1,25 1,35 Material: steel, polished, surface roughness: Ra=0,4 m maximum. Mass of gauge: 26 g 1

39、g. 3.2.2 Test procedure The gauge A shall be inserted into the socket-centre contact three times with a minimum depth of 1,25 mm. BS EN 61169-18:2011 10 61169-18 IEC:2011 This is a sizing operation and should only be carried out when the socket-centre contact is removed from the connector. After thi

40、s, the gauge B shall have a withdrawal force of 0,25 N minimum after inserted into socket-centre contact .The contact shall retain the mass of the gauge in a vertical downward position. This test also shall be carried out on connector when the socket-centre contact is not removed. In this case, ther

41、e is not any sizing operation. 3.3 Dimensions Standard test connectors Grade 0 3.3.1 Connector with pin-centre contact El ect r i cal and Me c h a n i c a l r e f e r e n c eAAA10-36UNS-2BA0. 0004i n0. 0004i n0. 01mm0. 01mm0. 038mm0. 0015i n0. 013mm0. 0005i n BBNot e 1Not e 1Electrical and mechanica

42、l referencee 1d10-36UNS-2BNote1hfgdacijmkl0,038 mm0,01 mm0,01 mm0,013 mmbIEC 056/11Figure 4 Connector with pin-centre contact (for dimensions and notes, see Table 4) Table 4 Dimensions of connector with pin-centre contact Ref. mm Min. Max.a 2,54 3,40b 2,03 -c 2,54 4,32d 0,000 0,076 e 0,000 0,050 f 4

43、,98 5,21 BS EN 61169-18:201161169-18 IEC:2011 11 Ref. mm Min. Max. g 3,17 3,22 h 0,08 max 45or R0,08 max i 2,79 nominal j 35 48 k 0,495 0,528 l - 0,25 m 1,40 1,65 NOTE 1 The diameters are chosen upon the assumption that the PTFE dielectric has a dielectric constant of 2,02 to give an impedance of 50

44、 0,5 .3.3.2 Connector with socket-centre contact INo f i l l et per mi t t ed Root c ut ac c ept abl e10-36UNS-2AINot e 1ASee Det ai l AAA0. 0004i n0. 0004i n0. 01mm0. 01mmEl ect r i cal and Me c h a n i c a l r e f e r e n c eNot e 20. 013mm0. 0005i n BNot e 1BDet ai l AEl ect r i cal and Me c h a

45、n i c a l r e f e r e n c eElectrical and mechanical referenceNote 1 10-36UNS-2AtBA0,01 mmoA0,01 mmuvpsqrywxIINo fill t permittedot cut cceptableSee Detail AANote1Note2Electrical and mechanical referenceabaaacadDetail A0,013 mmIEC 057/11Figure 5 Connector with socket-centre contact (for dimensions a

46、nd notes, see Table 5) BS EN 61169-18:2011 12 61169-18 IEC:2011 Table 5 Dimensions of connector with socket-centre contact Ref. mm Min. Max. o 3,89 - p 3,81 - q 0,38 1,14 r 0,000 0,076 s 0,000 0,050 t 2,79 nominal u 3,23 3,28 v 3,89 4,04 w 1,88 1,98 x 0,13 max 45 y 2 slots - 0,13/0,15 wide aa 1,52 1

47、,80 ab 2,92 3,30 ac 42 48 ad 0,05 - NOTE 1 The diameters are chosen upon the assumption that the PTFE dielectric has a dielectric constant of 2,02 to give an impedance of 50 0,5 . NOTE 2 Design for slotting is optional, and should meet electrical and mechanical requirements, when mating with 0,495 m

48、m to 0,528 mm pin. 4 Quality assessment procedure 4.1 General The following subclauses provide recommended rating, performance and test conditions to be considered when writing a detail specification. They also provide an appropriate schedule of tests with minimum levels of conformance inspection sa

49、mpling, together with the pro-forma blank detail specification (BDS) and instructions for the preparation of a detail specification. 4.2 Standard ratings and characteristics (see Clause 6 of IEC 61169-1) The values indicated below are recommended for SSMA series RF connectors and are given for the writer of the detail specification. They ar