BS EN 61169-1-1-1997 Radio-frequency connectors - Single multi-series dual-language blank detail specification《射频连接器 单个、多系列、双语空白详细规范》.pdf

《BS EN 61169-1-1-1997 Radio-frequency connectors - Single multi-series dual-language blank detail specification《射频连接器 单个、多系列、双语空白详细规范》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61169-1-1-1997 Radio-frequency connectors - Single multi-series dual-language blank detail specification《射频连接器 单个、多系列、双语空白详细规范》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61169-1-1:1997 IEC 1169-1-1: 1996 QC 220001: 1996 Radio-frequency connectors Part 1-1: Single, multi-series, dual-language blank detail specification The European Standard EN 61169-1-1:1997 has the status of a British Standard ICS 33.120.30BSEN 61169-1-1:1997 This British Stan

2、dard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 July 1997 BSI 02-1999 ISBN 0 580 27755 0 National foreword This British Standard is the English language version of EN61169-1-1:19

3、97. It is identical with IEC1169-1-1:1996. This standard is a harmonized specification within the IEC quality assessment system for electronic components (IECQ). In the IECQ System, this specification is numbered QC220001. The UK participation in its preparation was entrusted by Technical Committee

4、EPL/46, Cables, wires, waveguides, RF connectors and accessories for communication and signalling, to Subcommittee EPL/46/2, RF connectors and waveguides, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries

5、on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The Britis

6、h Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. A British Sta

7、ndard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover

8、, an inside front cover, pages i and ii, theEN title page, pages 2 to 14 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. N

9、o. Date CommentsBSEN 61169-1-1:1997 BSI 02-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 61169-1-1 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61169-1-1 May 1997 ICS 33.120.30 Descriptors: Electronic components, R.F. connectors, multi-series connec

10、tors English version Radio-frequency connectors Part 1-1: Single, multi-series, dual-language blank detailspecification (IEC 1169-1-1:1996) Connecteurs pour frquences radiolectriques Partie 1-1: Spcification particulire cadre bilingue unique pour plusieurs sries de connecteurs (CEI 1169-1-1:1996) Ho

11、chfrequenz-Steckverbinder Teil 1-1: Zweisprachiger einheitlicher Vordruck fr Bauartspezifikationen fr verschiedene Baureihen (IEC 1169-1-1:1996) This European Standard was approved by CENELEC on1997-03-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

12、the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exi

13、sts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national elec

14、trotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation El

15、ectrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61169-1-1:1997 EEN61169-1-1:1997 BSI 02-1999 2 Foreword Th

16、e text of the International Standard IEC1169-1-1:1996, prepared by SC46D, RF connectors, of IECTC46, Cables, wires, waveguides, R.F. connectors, and accessories for communication and signalling, was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN61169-1-1 on1997-03-11

17、without any modification. The following dates were fixed: This part 1-1 of EN61169 is to be used in conjunction with EN61169-1:1994 and its amendment A1:1996. Endorsement notice The text of the International Standard IEC1169-1-1:1996 was approved by CENELEC as a European Standard without any modific

18、ation. latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1998-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1998-03-01EN61169-1-1:1997 BSI 02-1999 3 Exemp

19、le de la spcification IECQ pour la srie 1169 IECQ Specification example for series 1169EN61169-1-1:1997 4 BSI 02-1999 Introduction and Instructions for the preparation of detail specifications for R.F. connectors produced under the IECQ System The numbers between square brackets in the BDS correspon

20、d to the following indications which shall be given: Identification of the detail specification (DS) 1 The name of the National Authorized Institution (NAI) under whose authority the DS is published and, if available, the organization from whom the DS is available. 2 The IECQ logo and the number all

21、otted to the DS by the IECQ general secretariat. 3 The number and issue number of the IECQ generic and sectional specification; also national reference if different. 4 If different from the IECQ number, the national number of the DS, date of issue and any further information required by the national

22、 system, together with any amendment numbers. Enter the series designation of the connector in the box below the IECQ logo in characters9mm approximately high. Identification of the component 5 Enter the following details: Style: the style designation or model number of the connector. The method of

23、cable/wire attachment to the centre and outer conductor: by deletion of inapplicable options. Special features and markings. Example: fitted with both panel and barrier seals. Mass: the maximum mass in grams, rounded upwards to the nearest whole number. If several variants (having differing mass) ar

24、e included, list the maximum mass of each variant separately. 6 Enter details of assessment level, characteristic impedance and climatic category. 7 Provide a reproduction of the outline drawing and panel piercing details showing maximum envelope dimensions of the relevant body style and, in the cas

25、e of a fixed connector, the position of the mounting plane relative to the front face of the connector. Information shall be given in the places indicated concerning the international documents see the sectional specification (SS) to which the interface dimension and the outline dimensions comply, t

26、ogether with any maximum panel thickness limitations for fixed connectors. The symbol may be converted to indicate either first-angle or third-angle projection by deleting the inappropriate part of the drawing: First angle Third angle 8 Particulars of all variants covered by the DS. Where appropriat

27、e, the information shall include: cable types (or sizes) applicable to each variant; alternative plated or protective finishes; details of alternative mounting flanges having either tapped or plain mounting holes; details of alternative solder spills or solder buckets for microwave component-mountin

28、g styles. 9 Performance data listing the most important characteristics of the connector in accordance with the requirements in3.1 of the SS. Deviations from the minimum requirements listed shall be clearly indicated. Non-applicable parameters shall be market “na”. 10 Enter the information as applic

29、able. 11 Refer to the test groupings and schedule of tests in subclause3.3 of the relevant sectional specification and enter the letter “a” in the “Test required” columns against those tests shown to be mandatory for the applicable, assessment level. At the discretion of the specification writer, th

30、e letter “a” shall be entered also to indicate any additional test(s) required. In the “Number of specimens” columns, the number shall be entered as given in3.3 of the relevant sectional specification for the applicable assessment level. For 5 and 6 the text to be given in the DS should be suitable

31、for an entry in IECQC001004 1)(specification list) or IECQC001005 2)(QPL). At the lower right-hand corner of each page enter the specification issue number of the detail specification. When all the information has been entered, these introductory pages should be detached from the completed DS and di

32、scarded. NOTEThis BDS has been laid out to provide entry lines on a1/6 inch(4,23mm), spacing to suit standard typewriter line spacing in ISO4882 3) . After adjusting the position for the first entry on each page, no further adjustment should be necessary. 1) IEC QC 001004: Specifications List. 2) IE

33、C QC 001005: Register of Firms, Products and Services approved under IECQ System, including ISO 9000. 3) ISO 4882:1979, Office machines and data processing equipment Line spacings and character spacings.EN61169-1-1:1997 BSI 02-1999 5EN61169-1-1:1997 6 BSI 02-1999EN61169-1-1:1997 BSI 02-1999 7 9 Perf

34、ormance (including limiting conditions of use) For the notes, see the end of the table.EN61169-1-1:1997 8 BSI 02-1999EN61169-1-1:1997 BSI 02-1999 9EN61169-1-1:1997 10 BSI 02-1999EN61169-1-1:1997 BSI 02-1999 11 10 Supplementary informationEN61169-1-1:1997 12 BSI 02-1999 11 Test schedule and inspectio

35、n requirements 11.1 Qualification approval procedures One of the following procedures shall be used: a) Fixed quantity sample procedure This shall consist of the appropriate fixed quantity sample passing the initial tests in group0 without any failures. The fixed quantity number of specimens shall b

36、e: Level M 36 specimens Level H 18 specimens Specimens for groups D1, D2, D4-D7 shall then be selected randomly from the group0 specimens and subjected to the inspection for their particular group. No failures are permitted. The number of specimens in each group D1, D2, D4-D6 shall be: Level M 6 spe

37、cimens Level H 3 specimens Any additional specimens required for group D7 inspection shall also first be subjected to group0 tests. No failures are permitted. A set of piece parts shall be randomly selected for group D3 inspection. No failures are permitted. b) Lot-by-lot procedure This shall consis

38、t of three consecutive lots passing the acceptance tests in groups A1 andB1. Specimens from these lots shall be randomly selected for periodic tests in groups D1, D2, D4-D7 and shall be subjected to the relevant inspection for their particular group. The number of specimens in each group D1, D2, D4-

39、D6 shall be: Level M 6 specimens Level H 3 specimens A set of piece parts shall be randomly selected for group D3 inspection. No failures are permitted. 11.2 Quality conformance inspection a) Lot-by-lot tests These shall consist of test groups A1 and B1 performed on a lot-by-lot basis. b) Periodic t

40、ests There are no group C tests for r.f. connectors, level H and M. 11.3 Maintenance of qualification approval This shall consist of the procedure in11.1 b) above. 11.4 Test schedule and inspection requirements Series Assessment levelEN61169-1-1:1997 BSI 02-1999 13 Fixed quantity sample procedure In

41、itial test sequence: Group0 Lot-by-lot procedure Acceptance tests; Groups A1 and B1 Inspections Test method IEC 1169-1 (QC220000) Subclause Test required Fixed quantity sample procedure Initial QA test sequence Lot-by-lot procedure acceptance tests Group Number of specimens Group IL AQL% Period Visu

42、al examination 9.1.2 A1 Lot-by-lot Outline dimensions Mechanical compatibility Engagement and separation 9.1.3.1 9.1.3.3 9.3.6 Gauge retention (resilient contacts) 9.3.4 0 B1 Lot-by-lot Sealing non-hermetic Sealing hermetic Voltage proof Solderability piece parts (d) Insulation resistance 9.4.5.1 9.

43、4.5.2 9.2.6 9.3.2.1.1 9.2.5EN61169-1-1:1997 14 BSI 02-1999 Fixed quantity sample procedure Remaining QA test groups lot-by-lot procedure Periodic group D tests Inspections Test method IEC1169-1 (QC220000) Subclause Test required Number of specimens Period Group D1 (d) Solderability connector assembl

44、ies Resistance to soldering heat Mechanical tests on cable fixing i) cable rotation (nutation) ii) cable pulling iii) cable bending iv) cable torsion Bending moment Strength of coupling mechanism 9.3.2.1.1 9.3.2.1.2 9.3.7 9.3.8 9.3.9 9.3.10 9.3.12 9.3.11 Group D2 (d) Contact resistance, outer conduc

45、tor and screen continuity and centre conductor continuity Centre and outer conductor continuity under severe mechanical conditioning Bump Vibration Shock Damp heat, steady state Salt mist 9.2.3 9.2.4 9.3.1.3 9.3.3 9.3.14 9.4.3 9.4.6 Group D3 Dimensions, piece parts and materials a 9.1.3 Group D4 (d)

46、 Mechanical endurance High-temperature endurance Sulphur dioxide 9.5 9.6 9.4.8 Group D5 (d) Reflection factor Screening effectiveness Water immersion 9.2.1 9.2.8 9.2.7 Group D6 (d) Centre contact captivation Discharge test (corona) Rapid change of temperature Climatic sequence 9.3.5 9.2.9 9.4.4 9.4.

47、2 Group D7 (d) Resistance to solvents and contaminating fluids 9.7 b a Unless using common piece parts. b One pair of connectors for each solvent, when applicable. Abbreviations: a na IL AQL (d) applicable; non-applicable; inspection level; acceptable quality level; destructive tests specimens shoul

48、d not be returned to stock.blankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

49、 | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve