BS EN 60819-3-1-2001 Non-cellulosic papers for electrical purposes - Specifications for individual materials - Filled glass paper《电工用非纤维素纸 专用材料规范 填充玻璃纸》.pdf

《BS EN 60819-3-1-2001 Non-cellulosic papers for electrical purposes - Specifications for individual materials - Filled glass paper《电工用非纤维素纸 专用材料规范 填充玻璃纸》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60819-3-1-2001 Non-cellulosic papers for electrical purposes - Specifications for individual materials - Filled glass paper《电工用非纤维素纸 专用材料规范 填充玻璃纸》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60819-3-1:2001 IEC 60819-3-1:2001 Non-cellulosic papers for electrical purposes Part 3: Specifications for individual materials Sheet 1: Filled glass paper The European Standard EN 60819-3-1:2001 has the status of a British Standard ICS 29.035.10 NO COPYING WITHOUT BSI PERMISS

2、ION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 60819-3-1:2001 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 29 November 2001 BSI 29 Novem

3、ber 2001 ISBN 0 580 38734 8 National foreword This British Standard is the official English language version of EN 60819-3-1:2001. It is identical with IEC 60819-3-1:2001 The UK participation in its preparation was entrusted to Technical Committee GEL/15, Insulating materials, to Subcommittee GEL/15

4、/3/10, Flexible composites and textiles, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been ren

5、umbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references The British Standards which implement international or European publications referred to in this document may be found

6、in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards a

7、re responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the U

8、K interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this

9、 document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 60819-3-1 NORME EUROPENNE EUROPISCHE NORM September 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechniq

10、ue Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60819-3-1:2001 E ICS 29.035.10 English version Non-cellulosic pape

11、rs for electrical purposes Part 3: Specifications for individual materials Sheet 1: Filled glass paper (IEC 60819-3-1:2001) Papiers non cellulosiques usages lectriques Partie 3: Spcifications pour matriaux particuliers Feuille 1: Papier charg base de fibres de verre (CEI 60819-3-1:2001) Vliesstoffe

12、auf Kunststofffaserbasis fr elektrotechnische Zwecke Teil 3: Bestimmungen fr einzelne Materialien Blatt 1: Gefllte Glaspapiere (IEC 60819-3-1:2001) This European Standard was approved by CENELEC on 2001-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipul

13、ate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard

14、 exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national

15、electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EN 60819-3-1:2001 - 2 - Foreword The text of document 15C/1205/FDIS, future ed

16、ition 1 of IEC 60819-3-1, prepared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60819-3-1 on 2001-09-01. The following dates were fixed: latest date by which the EN has to be implemented at national le

17、vel by publication of an identical national standard or by endorsement (dop) 2002-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2004-09-01 Annexes designated “normative“ are part of the body of the standard. In this standard, annex ZA is normati

18、ve. Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60819-3-1:2001 was approved by CENELEC as a European Standard without any modification. _ EN6081931:2001 BSI29November2001 260819-3-1 IEC:2001 3 INTRODUCTION This part of IEC 60819 is one of a ser

19、ies which deals with non-cellulosic papers for electrical purposes. The series consists of three parts: Part 1: Definitions and general requirements (IEC 60819-1) Part 2: Methods of test (IEC 60819-2) Part 3: Specifications for individual materials (IEC 60819-3). This standard contains one of the sh

20、eets comprising part 3 as follows: Sheet 1: Filled glass paper. EN6081931:2001 BSI29November2001 360819-3-1 IEC:2001 4 NON-CELLULOSIC PAPERS FOR ELECTRICAL PURPOSES Part 3: Specifications for individual materials Sheet 1: Filled glass paper 1 Scope This sheet of IEC 60819-3 specifies requirements fo

21、r two types of filled glass paper designated: P-FG type 1: high inorganic content paper with maximum organic content 15 %; P-FG type 2: medium inorganic content paper with maximum organic content 25 %. 2 Normative references The following normative documents contain provisions which, through referen

22、ce in the text, constitute provisions of this part of IEC 60819. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IEC 60819 are encouraged to investigate the possibility of applying the most

23、recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. IEC 60819-1:1995, Non-cellulosic papers for electrical purposes

24、Part 1: Definitions and general requirements IEC 60819-2, Non-cellulosic papers for electrical purposes Part 2: Methods of test 1 3 Requirements In addition to complying with the general requirements in IEC 60819-1, papers shall comply with the specific requirements appropriate to their type as give

25、n in table 1 and in 3.1, 3.2, 3.3, 3.4 and 3.5. 3.1 The average thickness of 10 measurements evenly distributed along a line at right angles to the machine direction of the paper of either type 1 or type 2 paper shall be within 15 % of the nominal thickness. Thickness measurements shall be made in a

26、ccordance with clause 4 of IEC 60819-2. 3.2 Loss of mass on ignition at 625 C for 1 h (see IEC 60819-2, clause 13) on the paper as received, deducting the moisture content, shall be: for P-FG type 1 not greater than 25 %; for P-FG type 2 not greater than 30 %. _ 1To be published. EN6081931:2001 BSI2

27、9November2001 460819-3-1 IEC:2001 5 3.3 Moisture content of type 1 paper shall not exceed 0,8 %. Moisture content of type 2 paper shall not exceed 1,3 % (see IEC 60819-2, clause 12). 3.4 Minimum value of elongation at break for type 1 paper shall be 0,9 %. Minimum value of elongation at break for ty

28、pe 2 paper shall be 2,3 %. Determine elongation at break in accordance with IEC 60819-2, clause 7. 3.5 Thermal classification: based on long-term thermal ageing tests and the resulting Arrhenius graph, experience has shown that non-cellulosic papers listed in this sheet may be suitable for use in el

29、ectrical apparatus and shall have a relative temperature index (RTI) up to 220 C. Table 1 Physical and electrical requirements Type 1 Type 2 Properties Clause of IEC 60819-2 Units Nominal thickness mm Minimum Maximum Minimum Maximum Grammage 5 g/m 2 0,08 0,13 0,18 0,25 0,38 0,50 0,76 1,50 108 157 23

30、1 350 461 692 1 429 146 212 312 474 624 936 1 934 55 97 221 75 131 299 Electrical strength 10 kV 0,08 0,13 0,18 0,25 0,38 0,50 0,76 1,50 0,9 1,4 1,9 2,7 3,6 4,4 6,8 NR NR NR NR NR NR NR 0,7 1,0 2,7 NR NR NR Tensile strength 7 N/10 mm 0,08 0,13 0,18 0,25 0,38 0,50 0,76 1,50 9 14 21 28 35 46 86 NR NR

31、NR NR NR NR NR 7 9 19 NR NR NR NOTE NR: no requirement. _ EN6081931:2001 BSI29November2001 5- 3 - EN 60819-3-1:2001 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference

32、, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated

33、in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year

34、 IEC 60819-1 1995 Non-cellulosic papers for electrical purposes Part 1: Definitions and general requirements EN 60819-1 1995 IEC 60819-2 2001 Part 2: Methods of test EN 60819-2 2001 EN6081931:2001 BSI29November2001 6BS EN 60819-3-1:2001 IEC 60819-3-1:2001 BSI 389 Chiswick High Road London W4 4AL BSI

35、 British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users

36、 of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretar

37、y of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying

38、standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to

39、 supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Vari

40、ous BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the

41、purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the co

42、pyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or othe

43、rwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.