BS EN 60684-3-343 to 345-2002 Specification for flexible insulating sleeving - Specification requirements for individual types of sleeving - Expandable braided ethylene chlorotrifl-.pdf

《BS EN 60684-3-343 to 345-2002 Specification for flexible insulating sleeving - Specification requirements for individual types of sleeving - Expandable braided ethylene chlorotrifl-.pdf》由会员分享，可在线阅读，更多相关《BS EN 60684-3-343 to 345-2002 Specification for flexible insulating sleeving - Specification requirements for individual types of sleeving - Expandable braided ethylene chlorotrifl-.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60684-3-343 to 345:2002 Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheets 343 to 345: Expandable braided ethylene chlorotrifluoroethylene (E-CTFE) textile sleeving, uncoated The European Standard EN 60684-3-343 to 345:2002 has the stat

2、us of a British Standard ICS 29.035.20 BS EN 60684-3-343 to 345:2002 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 19 December 2002 BSI

3、19 December 2002 ISBN 0 580 40986 4 National foreword This British Standard is the official English language version of EN 60684-3-343 to 345:2002. It is identical with IEC 60684-3-343 to 345:2002. It supersedes BS EN 60684-3-343 to 345:1994 which is withdrawn. The UK participation in its preparatio

4、n was entrusted by Technical Committee GEL/15, Insulating material, to Subcommittee GEL/15/3/5, Sleevings, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement int

5、ernational or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or British Standards Online. This publication does not purpo

6、rt to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee

7、 any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and

8、 a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 60684-3-343 to 345 NORME EUROPENNE EUROPISCHE NORM September 2002 CENELEC European Committee for Electrotechnic

9、al Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60

10、684-3-343 to 345:2002 E ICS 29.035.20 Supersedes EN 60684-3-343 to 345:1994 English version Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheets 343 to 345: Expandable braided ethylene chlorotrifluoroethylene (E-CTFE) textile sleeving, uncoated (IEC 60684-3-343

11、 to 345:2002) Gaines isolantes souples Partie 3: Spcifications pour types particuliers de gaines Feuilles 343 345: Gaines expansibles tresses, en thylne chlorotrifluorothylne (E-CTFE), tisses, non revtues (CEI 60684-3-343 to 345:2002) Isolierschluche Teil 3: Anforderungen fr einzelne Schlauchtypen B

12、ltter 343 bis 345: Aufweitbare, geflochtene Ethylen-Chlortrifluorethylen- Textilschluche (E-CTFE), unbeschichtet (IEC 60684-3-343 to 345:2002) This European Standard was approved by CENELEC on 2002-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate t

13、he conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exis

14、ts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national elect

15、rotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.Foreword The text of document 15C/1357/FDIS, future editi

16、on 2 of IEC 60684-3-343 to 345, prepared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60684-3-343 to 345 on 2002-09-01. This European Standard supersedes EN 60684-3-343 to 345:1994. The following dates

17、 were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2003-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2005-09-01 Annexes designated “normative

18、“ are part of the body of the standard. In this standard, annex ZA is normative. Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60684-3-343 to 345:2002 was approved by CENELEC as a European Standard without any modification. _ Page2 EN606843343to3

19、45:2002-48606-3543 ot 343 2002:CEI 3 INTRODUCTION This International Standard is one of a series which deals with flexible insulating sleeving for electrical purposes. The series consists of three parts: Part 1: Definitions and general requirements (IEC 60684-1); Part 2: Methods of test (IEC 60684-2

20、); Part 3: Specifications for individual types of sleeving (IEC 60684-3). This standard contains three of the sheets comprising Part 3, as follows: Sheet 343: Expandable braided ethylene chlorotrifluoroethylene (E-CTFE) textile sleeving, uncoated, thin wall thickness Sheet 344: Expandable braided et

21、hylene chlorotrifluoroethylene (E-CTFE) textile sleeving, uncoated, medium wall thickness Sheet 345: Expandable braided ethylene chlorotrifluoroethylene (E-CTFE) textile sleeving, uncoated, thick wall thickness Page3 EN606843343to345:2002-48606-3543 ot 343 2002:CEI 4 FLEXIBLE INSULATING SLEEVING Par

22、t 3: Specifications for individual types of sleeving Sheets 343 to 345: Expandable braided ethylene chlorotrifluoroethylene (E-CTFE) textile sleeving, uncoated 1 Scope This International Standard gives the requirements for sleeving having the property of expanding its internal diameter when compress

23、ed longitudinally and thereafter returning to its initial diameter after release of the compressing force. This expandable braided textile sleeving, uncoated, is constructed of ethylene chlorotrifluoroethylene (E-CTFE) monofilament yarns suitably processed to provide the mechanical ability to confor

24、m in the manner described above. These sleevings have been found suitable for use at temperatures up to 155 C. This sleeving is normally supplied in internal diameters between 6 mm and 63 mm and in three levels of wall thickness (thin (sheet 343), medium (sheet 344), and thick (sheet 345). It is nor

25、mally supplied in the following colours: black, white, brown, red, orange, yellow, green, blue, grey, and natural. Because of its open construction, this sleeving is normally used to provide air-space insulation. Therefore, no requirement for breakdown voltage is specified in this standard. (Any val

26、ue for this property should be given in the purchase contract, but a typical value is 1,5 kV/mm wall thickness, although a linear relationship cannot be assumed.) However, it serves to provide mechanical protection to circuit components such as wires, sleeves, and flat cable over which it is applied

27、 as a containing wrap or harness. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not

28、based on this specification alone. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

29、applies. IEC 60684-1:1980, Specification for flexible insulating sleeving Part 1: Definitions and general requirements IEC 60684-2:1997, Flexible insulating sleeving Part 2: Methods of test IEC 60757:1983, Code for designation of colours ISO 846:1997, Plastics Evaluation of the action of microorgani

30、sms ISO 1817:1999, Rubber, vulcanized Determination of the effect of liquids Page4 EN606843343to345:2002-48606-3543 ot 343 2002:CEI 5 3 Designation The sleeving shall be identified by the following designation: Description IEC Publication - Number - Part - Sheet Dimension (nominal interior diameter

31、in millimetres) Colour Code to identify that requirements from table 3 are applicable Sleeving IEC 60684 3 343 6 NC X The addition of “X“ at the end of the designation indicates that either or both of the properties contained in table 5 have been agreed upon and are included in the purchase contract

32、. Any abbreviation used for colour shall comply with IEC 60757. NC is used for “Natural Colour/ No Colour pigmentation”. Where no abbreviation is given, the colour shall be written in full. 4 Requirements 4.1 Standard requirements In addition to the general requirements given in IEC 60684-1, the sle

33、eving in the sizes normally available shall comply with the requirements in tables 1 and 2. 4.2 Special requirements If sleeving shall be supplied with any of the properties specified in table 5, it shall also comply with the appropriate requirements of table 5. 5 Sleeving conformance Conformance wi

34、th the requirements of this specification shall normally be based on the results of size 32 mm sleeving. Page5 EN606843343to345:2002-48606-3543 ot 343 2002:CEI 6 Table 1 Dimensional requirements Nominal internal diameter mm Minimum internal diameter in fully expanded state (by longitudinal compressi

35、on) mm 69 10 15 12 19 16 27 20 34 30 42 32 45 40 62 45 70 50 89 60 107 63 114 Wall thicknesses Sheet 343: Thin wall 0,30 mm min. Sheet 344: Medium wall 0,50 mm min. Sheet 345: Thick wall 0,75 mm min.Wall thickness dimensions shall be measured to the nearest 0,05 mm, using the suitable method of subc

36、lause 3.2 in IEC 60684-2. NOTE Because of the ease with which this sleeving can be dilated, care should be exercised in measuring the internal diameter using the plug gauges described in 3.1 of IEC 60684-2. Table 2 Standard requirements Property IEC 60684-2 clause or subclause Units Min. or max. Req

37、uirement Remarks Dimensions 3 mm Min. Table 1 Longitudinal change 9 % Max. +10 Test specimens shall be conditioned 4 h at 175 C 2 K Bending at low temperature 14 No cracking Full-section test specimens shall be conditioned unfilled at 70 C 5 K and tested by bending at that temperature around a 25 mm

38、 diameter metal rod Tensile strength 19.1* N Min. Table 3 Flame propagation 26 Method B s Max. 60 In addition, the indicator flag shall not be burned on any of the three tests, nor shall flaming or glowing particles ignite the cotton Resistance to fluids 36 19.1* % Min. 85 % retention of maximum loa

39、d at break Use the fluids and test temperatures specified in table 4 * The central value shall be reported as the maximum load at break. The jaws shall be separated at a uniform rate of 100 mm/min. Page6 EN606843343to345:2002-48606-3543 ot 343 2002:CEI 7 Table 3 Requirements for tensile strength Thi

40、n wall Medium wall Thick wall Sheet 343 Sheet 344 Sheet 345 Nominal internal diameter mm NNN 6 10 12 16 20 30 32 40 45 50 60 63 380 410 440 490 560 700 720 730 750 770 820 880 540 690 730 820 940 1 180 1 210 1 220 1 240 1 270 1 320 1 470 960 1 030 1 100 1 240 1 410 1 760 1 800 1 840 1 870 1 910 2 06

41、0 2 210 Page7 EN606843343to345:2002-48606-3543 ot 343 2002:CEI 8 Table 4 Resistance to selected fluids Test fluid No. Fluids Type Standard or symbol Immersion temperature C 2 K 1 Gasoline ISO 1817 Liquid B 23 2 Fuels Kerosene ISO 1817 Liquid F 23 3 Phosphate base ISO 1817 Liquid 103 23 4 Silicone ba

42、se S-1714* 23 5 Hydraulic fluids Mineral base H-520* 23 6 Synthetic base ISO 1817 Liquid 101 23 7 Mineral base ISO 1817 Oil No. 2 23 8 Mineral base O-1176* 23 9 Oils Mineral base O-142* 23 10 Isopropyl alcohol 23 11 Propanol 25 % White spirit 75 % 23 12 Cleaning fluids Solvent Methylethylketone 23 1

43、3 Runway de-icers Inhibited potassium acetate in water, 50 % 23 14 De-icing fluids Aircraft de-icers Ethylene glycol 80 % Water 20 % 23 * These are commercially available fluids which can be identified in aviation fluid guides. Other fluids and/or temperatures may be specified with specific needs. T

44、hese additional fluids shall be applicable when incorporated into agreements between the supplier and the customer. Table 5 Special requirements Property IEC 60684-2 clause or subclause or other reference Max. or min. Requirements Remarks Mould growth ISO 846, Method A Max. Scale 1 or better Fraying

45、 resistance 20 Max. Shall be subject to purchase contract Page8 EN606843343to345:2002Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publica

46、tions. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision.

47、 For undated references the latest edition of the publication referred to applies (including amendments). NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60684-1 1980 Specification

48、 for flexible insulating sleeving Part 1: Definitions and general requirements EN 60684-1 1995 IEC 60684-2 1997 Flexible insulating sleeving Part 2: Methods of test EN 60684-2 1997 IEC 60757 1983 Code for designation of colours HD 457 S1 1985 ISO 846 1997 Plastics - Evaluation of the action of micro

49、organisms EN ISO 846 1997 ISO 1817 1999 Rubber, vulcanized - Determination of the effect of liquids - Page9 EN606843343to345:2002BS EN 60684-3-343 to 345:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK