BS EN 60512-24-1-2012 Connectors for electronic equipment Tests and measurements Magnetic interference tests Test 24a Residual magnetism《电子设备连接器 试验和测量 磁场干扰试验 试验24a 剩磁》.pdf

《BS EN 60512-24-1-2012 Connectors for electronic equipment Tests and measurements Magnetic interference tests Test 24a Residual magnetism《电子设备连接器 试验和测量 磁场干扰试验 试验24a 剩磁》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60512-24-1-2012 Connectors for electronic equipment Tests and measurements Magnetic interference tests Test 24a Residual magnetism《电子设备连接器 试验和测量 磁场干扰试验 试验24a 剩磁》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 24-1: Magnetic interference tests Test 24a: Residual magnetismBS EN 60512-24-1:2012National forewordThis British St

2、andard is the UK implementation of EN 60512-24-1:2012. It isidentical to IEC 60512-24-1:2010.The UK participation in its preparation was entrusted to Technical CommitteeEPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this

3、 committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012 Published by BSI Standards Limited 2012 ISBN 978 0 580 62175 8 ICS 3

4、1.220.01Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 6051

5、2-24-1:2012EUROPEAN STANDARD EN 60512-24-1 NORME EUROPENNE EUROPISCHE NORM November 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brus

6、sels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-24-1:2012 E ICS 31.220.01 English version Connectors for electronic equipment - Tests and measurements - Part 24-1: Magnetic interference tests - Test 24a: Residual m

7、agnetism (IEC 60512-24-1:2010) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 24-1: Essais de perturbations magntiques - Essai 24a: Magntisme rsiduel (CEI 60512-24-1:2010) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 24-1: Prfungen im magnetisc

8、hen Strfeld - Prfung 24a: Restmagnetismus (IEC 60512-24-1:2010) This European Standard was approved by CENELEC on 2010-04-28. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standa

9、rd without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in

10、 any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croat

11、ia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turke

12、y and the United Kingdom. BS EN 60512-24-1:2012EN 60512-24-1:2012 - 2 - Foreword The text of document 48B/2027/CDV, future edition 1 of IEC 60512-24-1, prepared by SC 48B “Connectors“ of IEC/TC 48 “Electromechanical components and mechanical structures for electronic equipment“ was submitted to the

13、IEC-CENELEC parallel vote and approved by CENELEC as EN 60512-24-1:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-05-16 latest date by which the national stan

14、dards conflicting with the document have to be withdrawn (dow) 2015-04-28 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement

15、notice The text of the International Standard IEC 60512-24-1:2010 was approved by CENELEC as a European Standard without any modification. BS EN 60512-24-1:2012 4 60512-24-1 IEC:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 24-1: Magnetic interference tests Test 24a: Residual

16、magnetism 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a stan

17、dard method to measure the residual magnetism of a connector after exposure to a specified magnetic field. 2 Preparation of the specimen The connector shall be prepared and mounted in a fixture as required by the detail specification. 3 Test method A magnetometer with a suitable probe shall be place

18、d horizontally on a non-magnetic support with the probe positioned as far away from the measuring instrument as allowed by the connecting cord. The measuring instrument shall be set to the appropriate scale and the probe oriented so as to read “0“. The specimen shall be exposed to a magnetic field o

19、f approximately 0,5 T (5 000 G) three times. NOTE The specimen should not touch the polar parts of the magnet. Immediately after magnetization, the specimen shall be placed at a distance not exceeding 3 mm from the probe, without touching the probe. The specimen shall be oriented so as to obtain a m

20、aximum reading on the measuring instrument. 4 Requirements The value measured shall not exceed the maximum value specified by the detail specification. 5 Details to be specified When this test is required by the detail specification, the following details shall be specified: a) accessories to be fit

21、ted on the specimen; b) maximum value of the residual magnetism; c) any deviation from the standard test method. _ BS EN 60512-24-1:2012This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standar

22、ds-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raisi

23、ng standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant

24、 aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary fo

25、r PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 F

26、ax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9

27、001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand inter

28、national standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Members

29、hip Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documen

30、tation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publicati

31、on and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude t

32、he free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: