BS EN 60455-3-2-2003 Resin based reactive compounds used for electrical insulation - Specifications for individual materials - Quartz filled epoxy resinous compounds - Sheet 2 Quar.pdf

《BS EN 60455-3-2-2003 Resin based reactive compounds used for electrical insulation - Specifications for individual materials - Quartz filled epoxy resinous compounds - Sheet 2 Quar.pdf》由会员分享，可在线阅读，更多相关《BS EN 60455-3-2-2003 Resin based reactive compounds used for electrical insulation - Specifications for individual materials - Quartz filled epoxy resinous compounds - Sheet 2 Quar.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60455-3-2:2003 Resin based reactive compounds used for electrical insulation Part 3: Specifications for individual materials Sheet 2: Quartz filled epoxy resinous compounds The European Standard EN 60455-3-2:2003 has the status of a British Standard ICS 29.035.01 BS EN 60455-3

2、-2:2003 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 1 August 2003 BSI 1 August 2003 ISBN 0 580 42363 8 National foreword This British Standard is the official English language version of EN 60455-3-2:2003. It is identical with IEC 60455-3

3、-2:2003. It supersedes BS 5664-3.2:1997 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee GEL/15, Insulating material, to Subcommittee GEL/15/3, Material specifications, which has the responsibility to: A list of organizations represented on this subcom

4、mittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the

5、“Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from leg

6、al obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. S

7、ummary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comme

8、ntsEUROPEAN STANDARD EN 60455-3-2 NORME EUROPENNE EUROPISCHE NORM July 2003 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2003

9、 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60455-3-2:2003 E ICS 29.035.01 Supersedes HD 307.3.2 S2:1997English version Resin based reactive compounds used for electrical insulation Part 3: Specifications for individual mater

10、ials Sheet 2: Quartz filled epoxy resinous compounds (IEC 60455-3-2:2003) Composs ractifs base de rsines utiliss comme isolants lectriques Partie 3: Spcifications pour matriaux particuliers Feuille 2: Composs rsineux poxydes chargs de silice (CEI 60455-3-2:2003) Reaktionsharzmassen fr die Elektroiso

11、lierung Teil 3: Anforderungen an einzelne Werkstoffe Blatt 2: Quarzmehlgefllte Epoxidharzmassen (IEC 60455-3-2:2003) This European Standard was approved by CENELEC on 2003-06-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

12、his European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versi

13、ons (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of

14、Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. Foreword The text of document 15C/1462/FDIS, future edition 2 of IEC 60455-3-2, pr

15、epared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60455-3-2 on 2003-06-01. This European Standard replaces HD 307.3.2 S1:1997. References to HD 307.2 S1:1986 have been updated to EN 60455-2:1999 and

16、a new product, EP-F-7, has been introduced. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2004-03-01 latest date by which the national standards conflicting with the EN have

17、 to be withdrawn (dow) 2006-06-01 Annexes designated “normative“ are part of the body of the standard. In this standard, annex ZA is normative. Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60455-3-2:2003 was approved by CENELEC as a European Sta

18、ndard without any modification. _ Page2 EN6045532:2003INTRODUCTION This part of IEC 60455 is one of a series which deals with specifications for resin based reactive compounds used for electrical insulation. The series consists of three parts: Part 1: Definitions and general requirements (IEC 60455-

19、1) Part 2: Methods of test (IEC 60455-2) Part 3: Specifications for individual materials (IEC 60455-3) IEC 60455-3-2 is one of the specification sheets comprising Part 3, as follows: Sheet 2: Quartz filled epoxy resinous compounds Page3 EN6045532:2003RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICA

20、L INSULATION Part 3: Specifications for individual materials Sheet 2: Quartz filled epoxy resinous compounds 1 Scope This part of IEC 60455 contains the requirements for quartz filled epoxy resinous compounds in the cured form for types EP-F-1 to EP-F-7. Other materials than quartz may be introduced

21、 later. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60455-2:1998,

22、Resin-based reactive compounds used for electrical insulation Part 2: Methods of test 3 Requirements The requirements for quartz filled epoxy resinous compounds in the cured form are given in Table 2. If not otherwise specified, the requirements are for (23 2) C. NOTE 1 Materials with fillers differ

23、ent from quartz may be added as additional tables. Quartz filled epoxy resinous compounds purporting to comply with this standard shall contain between 45 % and 65 % by mass of quartz filler. NOTE 2 Materials for use in lower or higher temperature conditions may require additional tests to establish

24、 their suitability. 4 Special requirements When any of the following special properties are prescribed in the purchase contract, the method of test given below shall be used. Table 1 Requirements for quartz filled epoxy compounds in the uncured form Property Method of test in IEC 60455-2 Subclause V

25、iscosity 5.3 Epoxy equivalent 5.9 Shelf life 5.4 Pot life 5.16 Exothermic temperature peak 5.18.2 Total shrinkage 5.19 Page4 EN6045532:2003 Table 2 Requirements for quartz filled epoxy compounds in the cured form Method of test according to IEC 60455-2 Requirements for compounds types Properties Sub

26、clause Unit Value EP-F-1 EP-F-2 EP-F-3 EP-F-4 EP-F-5 EP-F-6 EP-F-7 Density 5.2 g/cm 3Range 1,7 1,9 Flexural (3 points) strength at rupture 6.3.3 MPa Min. 60 80 90 110 90 60 Tensile strength at rupture 6.3.1 MPa Min. 40 50 30 Impact strength, unnotched, flatwise 6.3.4 kJ/m 2Min. 3 4 6 7 8 8 Glass tra

27、nsition temperature C Typical values under consideration Temperature of deflection under load 6.4.4.2 C Min. 160 135 125 100 75 45 Typical values under consider- ation Flammability 6.4.5 FH2 Water absorption 6.5.1 (method 1) % Max. 0,3 0,3 0,3 0,3 0,4 1,5 Volume resistivity (no water immersion) 6.6.

28、1 cm Min. 1 10 1423 C, 48 Hz to 62 Hz Max. 0,02 23 C, 1 MHz Max. 0,35 Dissipation factor Temperature a , 48 Hz to 62 Hz 6.6.2 Max. 0,20 23 C, 48 Hz to 62 Hz Max. 5 Permittivity Temperature a , 48 Hz to 62 Hz 6.6.2 Max. 6 Electric strength b6.6.3 kV/mm Min. 10 Tracking resistance 6.6.4 Min. 400 300 T

29、hermal endurance by flexural strength to 50 % of initial value c6.4.7 Min. 140 130 130 120 105 90 Typical values under consider- ation Thermal endurance by loss of mass 6.4.7 Typical values under consideration aThe temperatures for determining dissipation factor and permittivity are as follows: EP-F

30、-1: 160 C, EP-F-2: 135 C, EP-F-3: 125 C, EP-F-4: 100 C, EP-F-5: 75 C, EP-F-6: 45 C. bThe specimen shall be 3 mm thick and of sufficient area to prevent flashover. c The value indicated for the temperature indices are minimum values which can therefore be considerably exceeded and should not be consi

31、dered as characterizing the category or as being related to the temperature of deflection under load. Page5 EN6045532:2003 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated re

32、ference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorp

33、orated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/

34、HD Year IEC 60455-2 1998 Resin based reactive compounds used for electrical insulation Part 2: Methods of test EN 60455-2 1999 Page6 EN6045532:2003BS EN 60455-3-2:2003 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for prep

35、aring British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editio

36、ns. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the insi

37、de front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publicatio

38、ns should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that

39、have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are a

40、lso available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price o

41、f standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information

42、about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extrac

43、t may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbo

44、ls, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.