BS EN 60107-1-1997 Methods of measurement on receivers for television broadcast transmission - General considerations - Measurements on displays at radio and video frequencies《电视广播.pdf

《BS EN 60107-1-1997 Methods of measurement on receivers for television broadcast transmission - General considerations - Measurements on displays at radio and video frequencies《电视广播.pdf》由会员分享，可在线阅读，更多相关《BS EN 60107-1-1997 Methods of measurement on receivers for television broadcast transmission - General considerations - Measurements on displays at radio and video frequencies《电视广播.pdf（132页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60107-1:1997 IEC 60107-1: 1997 Methods of measurement on receivers for television broadcast transmissions Part 1: General considerations Measurements on displays at radio and video frequencies The European Standard EN 60107-1:1997 has the status of a British Standard ICS 33.16

2、0.20BSEN60107-1:1997 This British Standard, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15 July 1997 BSI 07-1999 ISBN 0 580 27734 8 National foreword This British Standard is the English

3、 language version of EN60107-1:1997. It is identical with IEC60107-1:1997. It supersedes BS3549-1:1979 which will be withdrawn on1997-12-01. The UK participation in its preparation was entrusted by Technical Committee ELP/100, Audio, video and multimedia systems and equipment, to Subcommittee EPL/10

4、0/1, Receiving equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European de

5、velopments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact thatAnnex ZA lists normative references to international publications with their corresponding European publ

6、ications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standa

7、rd does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, a

8、n inside front cover, pages i and ii, theEN title page, pages 2 to 126 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.

9、 Date CommentsBSEN60107-1:1997 BSI 07-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 60107-1 7ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60107-1 May 1997 ICS 33.160.20 Descriptors: Television receivers, electric measurements, display devices, radio

10、frequencies, tests, electrical properties, sensitivity, luminance, chrominance, images, synchronisation, quality English version Methods of measurement on receivers for television broadcast transmissions Part 1: General considerations Measurements at radio and video frequencies (IEC 60107-1:1997) Mt

11、hodes de mesures applicables aux rcepteurs de tlvision Partie 1: Considrations gnrales Mesures aux domaines radiofrquences et vidofrquences (CEI 60107-1:1997) Meverfahren fr Empfnger von Fernseh-Rundfunksendungen Teil 1: Allgemeine Vorschriften, Messungen bei Radio- und Videofrequenzen (IEC 60107-1:

12、1997) This European Standard was approved by CENELEC on1997-03-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliograph

13、ical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a

14、 CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, N

15、orway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All r

16、ights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60107-1:1997 EEN60107-1:1997 BSI 07-1999 2 Foreword The text of document100A/5 + 5A/FDIS, future edition3 of IEC60107-1, prepared by SC100A, Multimedia end-user equipment, of IECTC100, Audio, video

17、 and multimedia systems and equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN60107-1 on1997-03-11. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. Annexes designated “informative” are given for information

18、 only. In this standard, Annex A, Annex B and Annex ZA are normative and Annex C is informative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC60107-1:1997 was approved by CENELEC as a European Standard without any modification. In the official vers

19、ion, for Annex C, Bibliography, the following notes have to be added for the standards indicated: IEC 61079-1 NOTEHarmonized as EN 61079-1:1993 (notmodified) IEC 61079-2 NOTEHarmonized as EN 61079-2:1993 (notmodified) IEC 61079-3 NOTEHarmonized as EN 61079-3:1993 (notmodified) IEC 61079-5 NOTEHarmon

20、ized as EN 61079-5:1993 (notmodified) Contents Page 1 General 7 1.1 Scope 7 1.2 Normative references 7 2 General explanation of terms 8 2.1 Definitions 8 2.2 Types of receivers 8 2.3 Peripheral connectors 8 3 General notes on measurement 9 3.1 General conditions 9 3.1.1 Operation conditions 9 3.1.2

21、Test room 9 3.1.3 Presentation of results 9 3.1.4 Environmental conditions 9 3.1.5 Precautions during measurement 9 3.1.6 Power supply 9 3.1.7 Stabilization period 10 3.2 Test signals 10 3.2.1 Video test signals 10 3.2.2 Audio test signals 14 3.2.3 Teletext test signals 14 3.3 Radiofrequency (r.f.)

22、television signal 31 3.3.1 Carrier levels 31 3.3.2 Reference modulation 31 3.3.3 Test channels 32 3.4 Radiofrequency input signals 33 3.4.1 Radiofrequency input signal level 33 3.4.2 Radiofrequency input arrangements 33 3.4.3 Radiofrequency input to built-in antennas 33 3.5 Measuring system and test

23、 instruments 35 3.5.1 Measuring system 35 3.5.2 Baseband test signal generators 35 3.5.3 Television test modulator 36 3.5.4 RF signal generator 36 3.5.5 Spectrum analyzer 36 3.5.6 Video noise meter 36 3.5.7 Oscilloscope 36 3.5.8 Vectorscope 36 3.5.9 Audio level/distortion meter 36 3.5.10 Passive dev

24、ices 36 3.5.11 Luminance meter and colorimeter 36 3.5.12 Other optical measuring instruments 37 3.6 Standard measuring conditions 37 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1997-12-01 latest date by

25、which the national standards conflicting with the EN have to be withdrawn (dow) 1997-12-01EN60107-1:1997 BSI 07-1999 3 Page 3.6.1 Standard input signal levels 37 3.6.2 Standard output signal levels 37 3.6.3 Standard receiver settings 39 3.6.4 Standard viewing conditions 39 3.6.5 General conditions 4

26、0 4 Initial tests under general operating conditions 40 4.1 Electrical and mechanical performance 40 4.2 Power consumption 41 5 Characteristics of radiofrequency channel 42 5.1 Tuning characteristics 42 5.1.1 Operating frequency and its stability 42 5.1.2 Fine tuning frequency range 42 5.1.3 Automat

27、ic frequency control (AFC) 42 5.1.4 Tuning sensitivity 43 5.1.5 Mechanical properties of tuning system 43 5.1.6 Performance characteristics of presettable tuning systems 44 5.1.7 Tuning steps 44 5.2 Sensitivity 47 5.2.1 General measuring conditions 47 5.2.2 Gain-limited sensitivity 47 5.2.3 Noise-li

28、mited sensitivity 48 5.2.4 Synchronizing sensitivity 48 5.2.5 Colour sensitivity 48 5.2.6 Coefficient of reflection at the antenna input 49 5.2.7 Automatic gain control (AGC) static characteristics 49 5.2.8 Automatic gain control (AGC) dynamic characteristics 50 5.2.9 Colour killing 50 5.2.10 Maximu

29、m usable single r.f. input signal level 50 5.2.11 Maximum usable multiple r.f. input signal level 51 5.3 Selectivity and response to undesired signals 52 5.3.1 General 52 5.3.2 Two-signal selectivity 53 5.3.3 Intermediate frequency interference ratio 54 5.3.4 Adjacent channel interference ratio 55 5

30、.3.5 Image interference ratio 56 5.3.6 Intermodulation interference ratio 57 5.3.7 Cross-modulation interference ratio 58 Page 5.3.8 IF beat interference ratio 59 5.3.9 Spurious frequency interference ratio 59 5.3.10 Internally generated interference 60 6 Characteristics of luminance and chrominance

31、 channels 62 6.1 Characteristics of the luminance channel 62 6.1.1 General measuring conditions 62 6.1.2 Amplitude response to video frequency 62 6.1.3 Group delay characteristics to video frequency 63 6.1.4 Linear waveform response 63 6.1.5 Line-time non-linearity 65 6.1.6 Chrominance to luminance

32、intermodulation 65 6.1.7 Black level and its stability 65 6.1.8 Cross luminance (SECAM system) 66 6.2 Characteristics of chrominance channels 68 6.2.1 General measuring conditions 68 6.2.2 Chrominance automatic gain control characteristics 69 6.2.3 Differential gain and differential phase 69 6.2.4 A

33、mplitude response to modulation frequency 70 6.2.5 Linear waveform response in chrominance channel 70 6.2.6 Luminance/chrominance delay inequality 72 6.2.7 Line-time non-linearity of chrominance signals 73 6.2.8 Colour signal reproduction characteristics 73 6.2.9 Stability of colour synchronization

34、74 6.2.10 Phase stability of subcarrier oscillator 74 6.2.11 Cross-colour distortion 75 6.2.12 Group delay characteristics at subcarrier frequency 77 6.2.13 Chrominance amplifier and limiter in SECAM receivers 77 6.3 Demodulation characteristics of chrominance signals inherent in each colour system

35、(NTSC, PAL and SECAM) 85 6.3.1 Errors of chrominance signal demodulation angle NTSC system 85 6.3.2 Errors of chrominance signal demodulation angle PAL system 87EN60107-1:1997 4 BSI 07-1999 Page 6.3.3 Effects of phase distortion on incoming signal for small picture areas PAL system 88 6.3.4 Direct a

36、nd delayed signal amplitude matching SECAM system 88 6.3.5 Colour flaming on luminance transients SECAM system 89 6.3.6 Influence of the reference frequency deviation of the FM demodulator in SECAM colour decoders 89 6.3.7 Deviation of the r.f. de-emphasis frequency adjustment in SECAM colour decode

37、rs 90 6.3.8 Colour crosstalk (SECAM system) 91 7 Characteristics of displayed pictures 95 7.1 General properties of the picture 95 7.1.1 General measuring conditions 95 7.1.2 Geometric distortion 95 7.1.3 Over- and under-scanning and centring 98 7.1.4 Luminance and contrast 99 7.1.5 Colour purity of

38、 colour CRT 100 7.1.6 White uniformity of colour CRT 100 7.1.7 Convergence and registration errors 101 7.1.8 White balance 101 7.1.9 Resolution 101 7.1.10 Interference due to asynchronicity of mains frequency with field scanning frequency 102 7.1.11 Sound to picture interference 103 7.1.12 Other cha

39、racteristics of the picture 103 7.2 Synchronizing quality 109 7.2.1 Synchronizing range 109 7.2.2 Pulling on whites 110 7.2.3 Pulling on field synchronization pulses 110 7.2.4 Quality of interlace 110 7.3 Picture size stability versus changes of CRT beam current 112 7.3.1 Picture breathing (static l

40、oading influences on picture geometry) 112 7.3.2 Local picture distortion (dynamic loading influences on picture geometry) 112 7.4 Characteristics inherent in projection type displays 113 7.4.1 General 113 7.4.2 Luminance uniformity 113 7.4.3 Uniformity of chromaticity 114 7.4.4 Viewing angle and de

41、pendence of luminance uniformity on the angle 114 Page 7.4.5 Dependence of chromaticity on viewing angle 115 7.4.6 Screen gain and luminous flux index of a projector 115 7.4.7 Blanking 117 7.5 Characteristics inherent in LCD displays 118 7.5.1 General 118 7.5.2 Luminance uniformity 119 7.5.3 Variati

42、on of luminance with time 119 7.5.4 Uniformity of chromaticity 119 7.5.5 Viewing angle and dependence of luminance uniformity on the angle 119 7.5.6 Dependence of chromaticity on viewing angle 119 7.6 Characteristics inherent in widescreen displays 119 7.6.1 General 119 7.6.2 Display mode 119 7.6.3

43、Methods of measurement 119 8 Characteristics inherent in the receivers using double-rate scan displays 120 8.1 General 120 9 Disturbance on the picture due to signals inserted into the field blanking interval 120 9.1 Introduction 120 9.2 Method of measurement 120 9.3 Presentation of results 121 10 C

44、haracteristics inherent in teletext signals 121 10.1 General 121 10.2 General measuring conditions 121 10.3 Characteristics of teletext signal 121 Annex A (normative) Analytical description of the offset-carrier colour bar signal 122 Annex B (normative) Calculation of the relative amplitude and the

45、group delay by the response of a modulated sine-squared pulse 123 Annex C (informative) Bibliography 124 Annex ZA (normative) Normative references tointernational publications with their corresponding European publications 125 Figure 1 Primary colour bar signals 15 Figure 2 NTSC split-field colour b

46、ar 15 Figure 3 NTSC colour bar signal (75/0/75/0) 16EN60107-1:1997 BSI 07-1999 5 Page Figure 4 NTSC colour bar signal (77/7,5/77/7,5) 16 Figure 5 PAL and SECAM full-field colour bar 16 Figure 6 PAL colour bar signal (100/0/75/0) 17 Figure 7 SECAM colour bar signal (100/0/75/0) 17 Figure 8 SECAM colo

47、ur bar signal (30/0/30/0) 17 Figure 9 Three vertical bar signal 18 Figure 10 Cross-hatch signals 18 Figure 11 Flat level signal 19 Figure 12 White window signal 19 Figure 13 Black and white window signal 20 Figure 14 Line and window signal 20 Figure 15 Two step signal 21 Figure 16 Colour reference s

48、ignal 21 Figure 17 Composite sine-wave signal 21 Figure 18 Multiburst signal 22 Figure 19 Multipulse signal 22 Figure 20 2T pulse and bar signal 22 Figure 21 Horizontal bar signal 23 Figure 22 Staircase signal 23 Figure 23 PLUGE signal 24 Figure 24 White PLUGE signal 25 Figure 25 Colour staircase si

49、gnal 26 Figure 26 Sine-wave modulated chrominance signal 26 Figure 27 Modulated 20T pulse and bar signals 27 Figure 28 Y/C timing test signal 28 Figure 29 Staircase-modulated chrominance signal 29 Figure 30 Modulated pedestal signal 29 Figure 31 Single colour bar signal 29 Figure 32 Offset-carrier colour bar signal 29 Figure 33 Four-line colour difference signal 30 Figure 34 Checkered pattern signal 31 Figure 35 Modulated radiofrequency signals 32 Figure 36 Measuri