BS EN 50267-2-2-1999 Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Procedures - Determination of degreep.pdf

《BS EN 50267-2-2-1999 Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Procedures - Determination of degreep.pdf》由会员分享，可在线阅读，更多相关《BS EN 50267-2-2-1999 Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Procedures - Determination of degreep.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Common test methods for cables under fire conditions - Tests on The European Standard EN 50267-2-2:1998 has the status of a British Standard BS EN 50267-2-2:1999 ICs 13.220.40: 29.060.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Copyright European Commit

2、tee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-ST3=BSI ES EN 5-2b7-2-2-EKGL 3999 U lb2Ybb4 0777483 733 direction of the Electrotechnical hd. No. Date Sector Committee, was published u

3、nder the authority of the Standards Committee and comes into effect on 16 September 1999 BS EN 50267-2-2:1999 Comments National foreword This British Standard is the English language version of EN 50267-2-2:1999. The UK participation in its preparation was entrusted by Technical Committee GEMO, Elec

4、tric cables, to Subcommittee GEI20/3, Insulation and sheath, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related international and European developments and promulgate interpretation, or propo

5、sals for change, and keep the UK interests informed; them in the UK A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be

6、found in the BSI Standarch Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Stand

7、ards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copyright notice

8、displayed in this document indicates when the document was last issued. O BSI 041999 I l ISBN O 680 32734 6 Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-EUR

9、OPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 50267-2-2 June 1998 ICs 13.220.40; 29.060.20 Descriptors: elecical installation, electrical cables, fire tests, combustion tests, combustion products, burning gases, corrosive gases, determination, acidity, measurements, pH conductivity, testing, con

10、ditions, procedures English version Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Part 2-2: Procedures - Determination of degree of acidity of gases for materials by materials by measuring pH and conductivity Mthodes dessai

11、 communes aux cbles soumis au feu - Essais sur les gaz mis lors de la combustion dun matriau prlev sur un cble - Partie 2-2: Procdures -Dtermination de lacidit des gaz des matriaux par une mesure du pH et de la conductivit Allgemeine Prfverfahren fr das Verhalten von Kabeln und isolierten Leitungen

12、im Brandfall -Prfung der bei der Verbrennung der Werkstoffe von Kabeln und isolierten Leitungen entstehenden Gase - Teil 2-2: Prfverfahren - Bestimmung des Grades der Aziditt von Gasen bei Werkstoffen durch pH-Wert und LeiWgkeit This European Standard was approved by CENELEC on 1998 04.01. CENELEC m

13、embers are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applica

14、tion to the Central Secretariat or to any CENELEC member. This European Standard exists in three oficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat

15、has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom

16、. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels O 1998 CENELEC - All rights of exploitation in any form and by any means reserve

17、d worldwide for CENELEC national members Ref. No. EN 50267-2-2: 1998 E Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-Page 2 EN 50267-2-2: 1998 Fore wo rd Thi

18、s European Standard was prepared by the Technical Committee CENELEC TC20, Electric Cables. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 50267-2-2 on 1998-04-0 1. The following dates were fixed: - latest date by which the EN has to be implem

19、ented at national level by publication of an identical national standard or by endorsement (dop) 1999-03-01 - latest date by which national standards conflicting with the EN have to be withdrawn (dow) 2000-03-0 1 Annexes designated “nonnative“ are part of the body of the standard. Annexes designated

20、 “informative“ are given for information only. In this standard annex A is informative. There is no normative annex. Contents Foreword 1 Scope 2 Normative references 3 Definition 4 Test apparatus 5 Test method and procedure 5. I General principle 5.2 Samples and conditioning 5.3 Test pieces 5.4 Proc

21、edure 5.5 Determination of pH and conductivity 6 Expression of the results Annex A (informative) Performance requirements Page 2 3 3 3 3 3 3 4 4 4 4 4 5 Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networ

22、king permitted without license from IHS-,-Page 3 EN 50267-2-2 : 1998 1 Scope EN 50267-2-2 specifies the test method and procedure for the detemination of the degree of acidity of gases evolved during the combustion of materials taken from electric or optical cables by measuring pH and conductivity.

23、NOTE The relevant cable standard should indicate which materials from the cable should be tested. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text a

24、nd the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.

25、EN 50267- 1, Common test methods for cables underfire conditions - Tests on gases evolved during the cornbusrion of materialsfrom cables. Part 1: Tesr apparum. EN 60695-4, Fire Hazard testing - Part 4: Terminology concemingfire tests. NOTE IEC 60695 is in the course of re-numbering its parts and sec

26、tions. This will also affect the equivalent ENS. 3 Definition For the purposes of EN 50267-2-2 the following definition applies. The definition is taken from EN 60695-4. 3.1 combustion exothermic reaction of a substance with an oxidizer with emission of effluent, generally accompanied by flames ando

27、r glowing and/or emission of smoke 4 Test apparatus The apparatus used shall be that specified in EN 50267-1 together with the following measuring instruments: - analytical balance of an accuracy of *O, 1 mg; - pH meter to an accuracy of *0,02, equipped with a suitable pH electrode; - Conductivity m

28、easuring device with a range lo2 pS/mm to lo2 pS/mm and a suitable electrode; - timer. 5 Test method and procedure 5.1 General principle A pre-determined quantity of the test material is burned in a tube hace. The evolved gases are trapped by bubbling through wash bottles filled with distilled or de

29、mineralized water. Each wash bottle shall contain approximately 450 mi of distilled or demineralized water with the following properties: pH 6,5 f 1,O; conductivity I 0,5pS/mm. The acidity is measured by determination of pH value. The conductivity of the solution is also measured. 0 BSlO9-1999 Copyr

30、ight European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-Page 4 EN 50267-2-2 : 1998 5.2 Samples and conditioning Representative samples of the material to be tested shall be

31、 taken. The samples shall be stored for at least 16 h at a temperature of (23 i 2) OC and a relative humidity of (50 f 5) %. 5.3 Test pieces A test piece shall consist of (1 O00 f 5) mg of the material to be tested taken from the representative sample. The test piece shall be cut into a number of sm

32、aller pieces. 5.4 Procedure The test pieces, which shall be weighed to an accuracy of 1 mg, shall be put into a combustion boat. They shall be evenly distributed on the bottom of the boat. The air flow shall be adjusted by means of a needle valve at (0,015 702) 1.h-I I10 % and kept constant during t

33、he test. NOTE 1 it is recommended that the air flow is not started until immediately prior to the commencement of the test. The temperature value shall be measured by a thermocouple suitably protected against corrosion and placed inside the tube. The boat containing the test pieces shall be quickly

34、inserted into the effective zone of the tube and the timer shall be started. The combustion boat shall be placed in such a way that the distance between the boat and the exit end of the effective heating zone is 2300 mm; the temperature measured at the position of the boat shall be not less than 935

35、 OC. The temperature measured at a position 300 mm fiom the boat in the direction of the air flow shall be not less than 900 “C. The combustion procedure under the air flow condition shall be continued for 30 min in the furnace. NOTE 2 The operator should take precautions, .e. the wearing of eye pro

36、tection and suitable protective clothing, because certain materials ignite quickly, and can cause blow-back“ of hot gases. Care should also be taken to avoid over-pressurisation of the system, and to allow for venting of exhaust gases. After the test, and before determination of the pH and conductiv

37、ity, the contents of both bottles shall be aggregated in a volumetric flask and made up to 1 O00 mi using water with the properties given in 5.1. NOTE 3 AAer removing the combustion boat, the tube has to be cleaned throughout its length by calcination at 950 OC. 5.5 Determination of the pH value and

38、 conductivity 5.5.1 Calibration of thepH meter The pH meter shall be calibrated as proposed by the instrument supplier. 5.5.2 Determination of the pH value and conductivity of the solution The pH value of the solution shall be determined at room temperature. The pH value shall be read by using the a

39、utomatic temperature compensation, usually integral with the instrument. Conductivity measurements shall be performed in accordance with the test procedures as prescribed by the supplier. 6 Expression of the results Two test determinations shall be undertaken on each non-metallic individual material

40、 to be tested. The test is considered to be passed if both the pH value of each sample of the material is not less than the specified value and the conductivity does not exceed the specified value. If one sample fails, the test determination shall be repeated on two further samples of the relevant m

41、aterial. Both repeat samples shall comply with specified limit values. Ca BSI 09-1 999 Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-Page 5 EN 50267-2-2: 199

42、8 Annex A (informative) Performance requirements No requirements for conformity are included in this standard. The method specified in this standard is intended for testing of individual materials used in cable construction. The use of this method will enable the requirements for individual material

43、s of a cable construction to be stated in the appropriate cable specification. Where no requirements are specified in the particular cable specification, and where the cable is described as “zero halogen” or “halogen-he” it is recommended that at least both the following requirements should be met f

44、or each of the individual materials of a cable constniction. a) The pH value as determined in 6, should not be less than 4,3, when related to one litre of water. b) The conductivity value as determined in 6, should not exceed 10 pS/mm, when related to one litre of water. In case of dispute over the

45、conductivity value, such as may occur if the recommended value is exceeded even though the test shows compliance with the recommended pH value, alternative methods of investigation should be agreed between interested parties. O BSI 09-1999 Copyright European Committee for Electrotechnical Standardiz

46、ation Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-BS EN 50267-2-2:1999 BSI 389 Chiswick High Road London w4 4AT.4 BSI - British Standards Institution BSI is the independent national body responsible for preparing British

47、Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the

48、constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover

49、. Tel O20 8996 9000. Fax: O20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automaticaliy receive the latest editions of standards. Buying standards Orders for ail BSI, international and foreign standards publications should be addressed to Customer Services. Tel: O20 8996 9001. Fax: O20 8996 7001. In response to orders for internationai standards, it is BSI pol