BS EN 50214-2006 Flat polyvinyl chloride sheathed flexible cables《扁平聚氯乙烯套装柔性电缆》.pdf

《BS EN 50214-2006 Flat polyvinyl chloride sheathed flexible cables《扁平聚氯乙烯套装柔性电缆》.pdf》由会员分享，可在线阅读，更多相关《BS EN 50214-2006 Flat polyvinyl chloride sheathed flexible cables《扁平聚氯乙烯套装柔性电缆》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 50214:2006Flat polyvinyl chloride sheathed flexible cablesThe European Standard EN 50214:2006 has the status of a British StandardICS 29.060.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g

2、48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Wed Apr 11 06:17:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 50214:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 20

3、07ISBN 978 0 580 50053 4National forewordThis British Standard was published by BSI. It is the UK implementation of EN 50214:2006. It supersedes BS EN 50214:1998 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee GEL/20, Electric cables, to Subcommittee G

4、EL/20/17, Low voltage cables.A list of organizations represented on GEL/20/17 can be obtained on request to its secretary.This British Standard makes reference to HD 308, which is not published directly by BSI but is incorporated into the content of other British Standards. The relevant information

5、on core colours can also be found in BS 7671. Similarly, specific tests and requirements from HD 21.1 can be cross-referenced directly as follows:HD 21 clause Requirement BS cross referenceHD 21.1 s/c 1.3 Common marking 5.3.3 of BS 6004:2000HD 21.1 clause 3.1 Indication of origin 5.3.2 of BS 6004:20

6、00HD 21.1 clause 3.2 Continuity of mark 5.3.2 of BS 6004:2000HD 21.1 clause 3.3 Durability 5.3.5 of BS 6004:2000This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer

7、immunity from legal obligations. Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Wed Apr 11 06:17:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD EN 50214 NORME EUROPENNE EUROPISCHE NORM November 2006 CENELEC European Committee for Electrotechnica

8、l Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 502

9、14:2006 E ICS 29.060.20 Supersedes HD 359 S2:1990 and EN 50214:1997English version Flat polyvinyl chloride sheathed flexible cables Cbles souples mplats gains en polychlorure de vinyle Flache PVC-ummantelte Steuerleitungen This European Standard was approved by CENELEC on 2006-10-01. CENELEC members

10、 are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application

11、to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has

12、the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway,

13、 Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, na, Wed Apr 11 06:17:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 50214:2006 2 Foreword This European Standard was prepared for Technical Committee CENELEC TC 20, Electric c

14、ables, with the agreement of CEN TC 10, Lifts, escalators and moving walks. The text of the draft was submitted to the formal vote and was approved by CENELEC as EN 50214 on 2006-10-01. This European Standard supersedes EN 50214:1997 and HD 359 S2:1990. The following dates were fixed: latest date by

15、 which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-10-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2008-01-01 _ Licensed Copy: Wang Bin, na, Wed Apr 11 06:17:25 GMT+0

16、0:00 2007, Uncontrolled Copy, (c) BSI 3 EN 50214:2006 Contents Page 1 Scope 5 2 Normative references .5 3 Definitions 6 4 Requirements for the construction of cables7 4.1 General .7 4.2 Core identification .7 4.3 Telecommunication Units 7 5 Flat PVC sheathed flexible cables for low rise lifts 8 5.1

17、Code designation 8 5.2 Rated voltage8 5.3 Construction8 5.4 Tests.10 6 Flat PVC sheathed flexible cables, of rated voltage 300/500 V, for high rise, high speed lifts.11 6.1 Code designation 11 6.2 Rated voltage11 6.3 Construction11 6.4 Tests.13 7 Flat PVC sheathed flexible cable of rated voltage 450

18、/750 V .16 7.1 Code designation 16 7.2 Rated voltage16 7.3 Construction16 7.4 Tests.18 8 Test methods 19 9 Marking .19 9.1 General .19 9.2 Common Marking 19 10 Guide to use .19 Annex A (normative) Test methods.20 Annex B (informative) Guide to use 26 Figure 1 Cable without strain bearing member .10

19、Figure 2 Cable with strain bearing member 10 Figure A.1 Adherence test for strain bearing member (method 1).23 Figure A.2 Adherence test for strain bearing member (method 2, showing two examples of clamping device).24 Figure A.3 Adherence between cores and sheath 25 Table 1 Composition of cables .8

20、Table 2 Grouping of cores9 Table 3 General data .10 Table 4 Composition of cables .12 Licensed Copy: Wang Bin, na, Wed Apr 11 06:17:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 50214:2006 4 Table 5 General data .13 Table 6 List of applicable tests.14 Table 7 List of additional applicable tests fo

21、r cables with strain bearing member(s) .15 Table 8 Composition of cables .16 Table 9 Grouping of cores17 Table 10 General Data.18 Table 11 List of Applicable Tests .18 Licensed Copy: Wang Bin, na, Wed Apr 11 06:17:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 5 EN 50214:2006 1 Scope This European St

22、andard covers the construction, requirements and particular test methods for flat, flexible PVC insulated and PVC sheathed cables, of rated voltage Uo/U 300/500 V, for use in passenger and goods lifts (elevators), and Uo/U 450/750 V for general purposes and for special applications such as hoists an

23、d travelling cranes. Cables of composite construction (for instance, cables with cores of different sizes) are not specified, but conditions are given for the inclusion of telecommunication units into the cables. NOTE 1 This revision is in accordance with an agreement with CEN TC 10 to specify in th

24、e same standard a) flexible cables for lifts as required by EN 81, and b) flexible cable for applications such as hoists and travelling cranes, previously found in HD 359. In accordance with this agreement only those cables in Clauses 5 and 6 are suitable for use with EN 81. NOTE 2 The limits for th

25、e overall diameter of the cables have been calculated in accordance with EN 60719. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the

26、 referenced document (including any amendments) applies. EN 81 Series Safety rules for the construction and installation of lifts EN 50334 Marking by inscription for the identification of cores of electric cables EN 50363 Series Insulating, sheathing and covering materials for low voltage energy cab

27、les EN 50395 Electrical test methods for low voltage energy cables EN 50396 Non electrical test methods for low voltage energy cables EN 60228 Conductors of insulated cables (IEC 60228) EN 60332-1-2 Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame

28、propagation for a single insulated wire or cable - Procedure for 1 kW pre-mixed flame (IEC 60332-1-2) EN 60719 Calculation of the lower and upper limits for the average outer dimensions of cables with circular copper conductors and of rated voltages up to and including 450/750V (IEC 60719) EN 60811

29、Series Insulating and sheathing materials of electric and optical cables - Common test methods (IEC 60811 series) HD 21 Series Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation HD 308 Identification of cores in cables and flexible cords IEC 60227-6 Polyvinyl

30、chloride insulated cables of rated voltages up to and including 450/750 V - Part 6: Lift cables and cables for flexible connections Licensed Copy: Wang Bin, na, Wed Apr 11 06:17:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 50214:2006 6 3 Definitions 3.1 Definitions relating to insulating and shea

31、thing materials 3.1.1 type of compound the category in which a compound is placed according to its properties, and determined by specific tests. The type designation is not directly related to the composition of the compound 3.1.2 polyvinyl chloride compound (PVC) combinations of materials, of which

32、 polyvinyl chloride is the characteristic constituent, suitably selected, proportioned and treated which meet the requirements given in the particular specification 3.2 Definitions relating to the tests 3.2.1 type tests (Symbol T) tests required to be made before supplying a type of cable covered by

33、 this standard on a general commercial basis, in order to demonstrate satisfactory performance characteristics to meet the intended application. These tests are of such a nature that, after they have been made, they need not be repeated unless changes are made in the cable materials, design or type

34、of manufacturing process which might change the performance characteristics 3.2.2 sample tests (Symbol S) tests made on samples of completed cable, or components taken from a completed cable adequate to verify that the finished product meets the design specifications 3.2.3 routine tests (Symbol R) t

35、ests made on all production cable lengths to demonstrate their integrity 3.3 rated voltage the rated voltage of a cable is the reference voltage for which the cable is designed, and which serves to define the electrical tests The rated voltage is expressed by the combination of two values Uo/U, expr

36、essed in volts: Uobeing the r.m.s. value between any insulated conductor and “earth“ (metal covering of the cable or the surrounding medium); U being the r.m.s. value between any two phase-conductors of a multicore cable or of a system of single-core cables. In an alternating current system, the rat

37、ed voltage of a cable shall be at least equal to the nominal voltage of the system for which it is intended. This condition applies both to the value Uoand to the value U. In a direct current system, the nominal voltage between conductors shall be not higher than 1,5 times the rated voltage (U) of t

38、he cable, and the nominal voltage between any conductor and earth shall not be higher than 1,5 times the rated voltage (Uo) of the cable. NOTE The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage

39、 than its rated voltage if the latter is at least equal to the nominal voltage of the system. Licensed Copy: Wang Bin, na, Wed Apr 11 06:17:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 7 EN 50214:2006 3.4 freely suspended length the unsupported allowed length of cable between two fixing points 3.5

40、strain bearing member (sbm) metallic or non-metallic high tensile strand or bunch included in the cable construction in order to hold the cable weight 4 Requirements for the construction of cables 4.1 General Unless otherwise indicated in Clauses 5, 6 or 7 of this EN, the cables shall comply with th

41、e general requirements specified in HD 21.1, Clause 5. 4.2 Core identification Both cables with or without a green-and-yellow core are harmonised. For cables with five cores or fewer, the identification of the remaining cores shall be either by colours, in accordance with a) below, or by numbers in

42、accordance with b) below. For cables with six cores or more only identification by numbers shall be used, except for any green-and-yellow core. a) Identification by colours The identification system of HD 308 shall be used. b) Identification by numbers Identification by numbers shall be in accordanc

43、e with EN 50334. The green-and-yellow core, if any, shall not be identified by a number. 4.3 Telecommunication Units It shall be permitted to introduce telecommunication units into the cable construction described in Clauses 5 and 6, subject to the following conditions: 1) units shall be chosen from

44、 copper pairs or copper coaxial or optical fibres; NOTE Two pairs may alternatively be included as a quad. 2) units shall have a diameter equal or very close to the diameter of insulated cores; 3) preferably the number of telecommunication units in a cable shall not exceed three; 4) the position of

45、units shall be central and symmetrical; 5) thickness (e2) of the cable sheath, where measured over telecommunication units, shall comply with the requirements for minimum thickness (see 5.3.5 and 6.3.5) but shall not be taken into account when calculating the mean value; 6) the colour or identificat

46、ion of the outer sheath over units shall not conflict with that of the cores in 4.2. However, no restriction shall be placed on colours used for insulations under an outer sheath. Licensed Copy: Wang Bin, na, Wed Apr 11 06:17:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 50214:2006 8 5 Flat PVC sh

47、eathed flexible cables, of rated voltage 300/500 V, for low rise lifts 5.1 Code designation Without strain bearing members: H05VVH6-F With strain bearing members: H05VVD3H6-F 5.2 Rated voltage 300/500 V. 5.3 Construction 5.3.1 Conductor Material: copper Number of conductors: 4 up to 24 Nominal cross

48、 sections: 0,75 mm and 1 mm The conductors shall be in accordance with the requirements of Class 5 given in EN 60228. 5.3.2 Insulation The insulation shall be PVC compound of type TI 2 to EN 50363-3 applied around each conductor. The mean value of the thickness of insulation shall be not less than t

49、he specified value for each type and size of cable shown in Table 3. However, the thickness at any place may be less than the specified value provided that the difference does not exceed 0,1 mm + 10 % of the specified value. Compliance shall be checked by the test given in EN 50396, 4.1. The insulation resistance at 70 C shall be not less than the values given in Table 3. 5.3.3 Assembly of cores The preferred number of cores for the composition of the cables is given in Table 1, according to the nominal cross