BS EN 29009-1994 Glass containers - Height and non-parallelism of finish with reference to container base - Test methods《玻璃容器 以容器底为基准的瓶口高度和不平行性 试验方法》.pdf

《BS EN 29009-1994 Glass containers - Height and non-parallelism of finish with reference to container base - Test methods《玻璃容器 以容器底为基准的瓶口高度和不平行性 试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 29009-1994 Glass containers - Height and non-parallelism of finish with reference to container base - Test methods《玻璃容器 以容器底为基准的瓶口高度和不平行性 试验方法》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 29009:1994 ISO 9009:1991 Glass containers Height and non-parallelism of finish with reference to container base Test methods The European Standard EN 29009:1994 has the status of a British Standard UDC 621.798.147:666.171/172.531.717BSEN29009:1994 This British Standard, having

2、 been prepared under the directionof the Packaging and Freight Containers Standards Policy Committee, was publishedunder the authority ofthe Standards Board and comesinto effect on 15 July 1994 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference PKM/6 Dr

3、aft for comment 88/45701 DC ISBN 0 580 22989 0 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitu

4、t Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland I

5、reland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normaliza

6、cin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN29009:1994 BSI 09-1999 i Contents Page Cooperating organizations Inside front co

7、ver National foreword ii Foreword 2 1 Scope 3 2 Normative reference 3 3 Definitions 3 4 Principle 3 5 Apparatus 3 6 Sampling 3 7 Procedure 3 8 Expression of results 5 9 Test report 5 National annex NA (informative) Committees responsible Inside back cover Figure 1 Non-parallelism 4 Figure 2 Example

8、of a height gauge 4BSEN29009:1994 ii BSI 09-1999 National foreword This British Standard has been prepared under the direction of the Packaging and Freight Containers Standards Policy Committee and is the English language version of EN29009:1993 Glass containers Height and non-parallelism of finish

9、with reference to container base Test methods, published by the European Committee for Standardization (CEN). It is identical with ISO9009:1991 Glass containers Height and non-parallelism of finish with reference to container base Test methods, published by the International Organization for Standar

10、dization (ISO). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This doc

11、ument comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages2 to6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front c

12、over.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 29009 April 1994 UDC 621.798.147:666.171/172.531.717 Descriptors: Containers, glass packaging, tests, determination, height, parallelism, dimensional measurements English version Glass containers Height and non-parallelism of finish with refe

13、rence to container base Test methods (ISO 9009:1991) Rcipients en verre Hauteur et non-paralllisme la bague par rapport au fonddu rcipient Mthodes dessai (ISO9009:1991) Behltnisse aus Glas Hhe und Nichtparallelitt von Mndung und Behltnisboden Prfverfahren (ISO9009:1991) This European Standard was ap

14、proved by CEN on 1994-04-01. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national s

15、tandards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified

16、 to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CE

17、N European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1994 Copyright reserved to CEN members Ref. No. EN 29009:1994 EEN29009:1994 BSI 09-1999 2 Foreword On the proposal of the CEN Central Secret

18、ariat, the Technical Board decided to submit the International Standard: ISO 9009:1991, Glass containers Height and non-parallelism of finish with reference to container base Test methods. to the formal vote. The result of the formal vote was positive. This European Standard shall be given the statu

19、s of a national standard, either by publication of an identical text or by endorsement, at the latest by October1994, and conflicting national standards shall be withdrawn at the latest by October1994. In accordance with the CEN/CENELEC Internal Regulations, the following countries are bound to impl

20、ement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom.EN29009:1994 BSI 09-1999 3 1 Scope This International Standard specifies test methods for determ

21、ining the height and the non-parallelism of finish with reference to the container base of glass containers. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the e

22、dition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently

23、valid International Standards. ISO 7348:1991, Glass containers Manufacture Vocabulary. 3 Definitions For the purposes of this International Standard, the definitions given in ISO7348and the following definitions apply. 3.1 (maximum) height of a container the distance between the highest point on the

24、 plane of the top surface of the finish and the standing surface (See Figure 1.) 3.2 minimum height of a container the distance between the lowest point on the plane of the top surface of the finish and the standing surface (See Figure 1.) 3.3 non-parallelism the difference between the maximum and m

25、inimum heights of a container (See Figure 1.) 4 Principle 4.1 Checking of the height of a container using maximum and minimum GO/NO GO gauges or by using an appropriate measuring instrument. Determination of the (maximum) height. 4.2 Determination of the non-parallelism of finish. 5 Apparatus 5.1 Fo

26、r checking the height Various types of gauge exist. Examples are given in5.1.1 and5.1.2. 5.1.1 Height gauge, consisting for example of a baseplate with one or two vertical pillars and a) a fixed horizontal cross-piece, in which case thedistance between the baseplate and the cross-piece is equivalent

27、 to the dimension to be gauged, or b) a fixed horizontal cross-piece with a step, in which case the distances between the baseplate and the two portions of the cross-piece are equivalent to the maximum and minimum heights to be gauged (see, for example, Figure 2), or c) an adjustable horizontal cros

28、s-piece, which may be fixed at a distance from the baseplate equivalent to the distance to be gauged. 5.1.2 Window gauge, which combines minimum body diameter and maximum height. 5.2 For determination of height Various types of apparatus exist, such as an engineering height vernier and a micrometer

29、height gauge. Such apparatus shall have an accuracy of measurement of at least0,1mm. 5.3 For determination of non-parallelism The apparatus may be a) that described in5.1.1 c) together with feeler gauges in0,1mm steps, or b) the apparatus described in5.2. For quick qualitative determinations, a spir

30、it level may be used. 6 Sampling Sampling shall form the subject of agreement between the parties concerned. 7 Procedure 7.1 Height of container 7.1.1 Quick check Place the container on a metal baseplate. Set up a height gauge (5.1.1) (see, for example, Figure 2) so that the minimum and maximum heig

31、hts correspond to the height tolerance requirements to an accuracy of 0,1mm. Determine those containers which slide under the highest portion of the gauge and which do not slide under the lowest portion of the gauge.EN29009:1994 4 BSI 09-1999 Figure 1 Non-parallelism Figure 2 Example of a height gau

32、geEN29009:1994 BSI 09-1999 5 7.1.2 Determination of (maximum) height Using an engineering height vernier or other suitable apparatus (5.2), measure the (maximum) height of the container to an accuracy of0,1mm. 7.2 Non-parallelism of finish with reference to container base Place the container on a me

33、tal baseplate. Using an engineering height vernier or other suitable apparatus (5.2) measure, to an accuracy of0,1mm, the lowest point of the finish (i.e. the minimum height) and, if not already determined in7.1.2, the highest point of the finish (i.e. the maximum height) (see Figure 1). 8 Expressio

34、n of results 8.1 Height of container 8.1.1 Quick check (see7.1.1) If results by attributes are required, take as the result the number of containers which meet the height tolerance requirements. 8.1.2 (Maximum) height (see 7.1.2) Take as the result the height, in millimetres, determined in7.1.2. 8.2

35、 Non-parallelism of finish with reference to container base Take as the result the difference between the maximum and minimum heights, in millimetres, determined in7.2. 9 Test report The test report shall specify the following information: a) reference to this International Standard; b) reference to

36、 the test method(s) used (i.e.7.1 and/or7.2); c) the size of the sample and the type of container tested; d) manufacturing details; e) the type of apparatus used; f) the results obtained; g) the testers name and signature, and date of test.6 blankBSEN29009:1994 BSI 09-1999 National annex NA (informa

37、tive) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Packaging and Freight Containers Standards Policy Committee (PKM/-) to Technical Committee PKM/6, upon which the following bodies were represented: Association of the Briti

38、sh Pharmaceutical Industry Brewers Society British Glass Manufacturers Confederation British Pharmacopoeia Commission British Plastics Federation British Retail Consortium British Soft Drinks Association Ltd. Campden Food and Drink Research Association Child Accident Prevention Trust Consumer Policy

39、 Committee of BSI Dairy Trade Federation Department of Trade and Industry (Consumer Safety Unit, CA Division) Food and Drink Federation Institute of Trading Standards Administration Metal Packaging Manufacturers Association National Association of Cider Makers Royal Society for the Prevention of Acc

40、idents Scotch Whisky Association Scottish Association of Soft Drinks Manufacturers Welsh Beekeepers Association Wine and Spirit Association of Great BritainBS EN 29009:1994 ISO9009:1991 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body respo

41、nsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendmen

42、ts or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found

43、on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications shou

44、ld be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide

45、 range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111

46、. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsist

47、s in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any m

48、eans electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.