BS EN 170101-2001 Harmonized system of quality assessment for electronic components - Blank detail specification - Waveguide type dielectric resonators - Capability approval《电子元器件质.pdf

《BS EN 170101-2001 Harmonized system of quality assessment for electronic components - Blank detail specification - Waveguide type dielectric resonators - Capability approval《电子元器件质.pdf》由会员分享，可在线阅读，更多相关《BS EN 170101-2001 Harmonized system of quality assessment for electronic components - Blank detail specification - Waveguide type dielectric resonators - Capability approval《电子元器件质.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 170101:2001 Harmonized system of quality assessment for electronic components Blank detail specification: Waveguide type dielectric resonators Capability approval The European Standard EN 170101:2001 has the status of a British Standard ICS 31.140 NO COPYING WITHOUT BSI PERMIS

2、SION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 170101:2001 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 26 November 2001 BSI 26 Novembe

3、r 2001 ISBN 0 580 38723 2 National foreword This British Standard is the official English language version of EN 170101:2001 published by the European Committee for Electrotechnical Standardization (CENELEC). The UK participation in its preparation was entrusted to Technical Committee EPL/49, Piezoe

4、lectric devices for frequency control and selection, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this d

5、ocument may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users o

6、f British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or p

7、roposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7, and a back cover. The BSI copyright date dis

8、played in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 170101 NORME EUROPENNE EUROPISCHE NORM August 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electr

9、otechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 170101:2001 E ICS 31.140 English version Blank detail Spec

10、ification: Waveguide type dielectric resonators - Capability approval Spcification particulire cadre: Rsonateurs dilectriques modes guids - Agrment de savoir-faire Vordruck fr Bauartspezifikation: Dielektrische Resonatoren vom Wellenleitertyp - Befhigungsanerkennung This European Standard was approv

11、ed by CENELEC on 2001-06-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nation

12、al standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language

13、and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain

14、, Sweden, Switzerland and United Kingdom.EN 170101:2001 - 2 - Foreword This European Standard was prepared by the Technical Committee CENELEC TC 49, Piezoelectric devices for frequency control and selection. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by C

15、ENELEC as EN 170101 on 2001-06-01. The following dates were fixed: - Latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2002-08-01 - Latest date by which the national standards conflicting with the EN have to b

16、e withdrawn (dow) 2004-08-01 Annexes designated “informative“ are given for information only. In this standard, annex A is informative.- 3 - EN 170101:2001 Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for

17、 the minimum content of detail specifications. The front page layout shown on page 4 is applicable to detail specifications for standard catalogue items only. For custom-built waveguide type dielectric resonators where the detail specification is not intended for publication, a suggested layout for

18、the front page is given in annex A. This is not mandatory, but it is recommended that the layout should be followed whenever possible. Key for page 4 The numbers between the brackets on page 4 correspond to the following information which should be given in the appropriate boxes. (1) The name of the

19、 National Standards Organization under whose authority the detail specification is published and, if applicable, the organization from whom the detail specification is available. (2) The EN symbol and the number allotted to the detail specification by the Secretariat. (3) The number and issue number

20、 of the EN generic or sectional specification as relevant; also national reference if different. (4) If different from the EN number, the national number of the detail specification, date of issue and any further information required by the national system, together with any amendment numbers. (5) A

21、 brief description of the waveguide type dielectric resonator or range of resonators (For example, nominal frequency and type of resonator). For (5) the text to be given in the detail specification should be suitable for any entry in CECC 00 200 (QPL) and CECC 00 300 (Library List). (6) An outline d

22、rawing with main dimensions which are of importance for interchangeability and/or reference to the appropriate national or international document for outlines. Alternatively, this drawing may be given in an annex to the detail specification.EN 170101:2001 - 4 - Specification available from: (1) EN 1

23、70101XXX (2) Page 1 of ELECTRONIC COMPONENTS OF ASSESSED (3) QUALITY BY CAPABILITY APPROVAL IN ACCORDANCE WITH: (4) Outline and dimensions (6) (first angle projection): Dimensions in mm (5) 1 Ratings (see 1.4 of EN 170000 for preferred ratings) Operating temperature range Climatic category Mechanica

24、l test severities Information about manufacturers who have components qualified to this detail specification is available in the current CECC 00 200. 2 Characteristics (see 1.3 of EN 170000) Nominal frequency Reference temperature Frequency tolerance (s) (if applicable) Insertion attenuation In addi

25、tion other characteristics may be stated.- 5 - EN 170101:2001 3 Related documents Generic specification EN 170000. Sectional specification EN 170100. 4 Marking The marking of the resonator and the primary package shall be in accordance with the requirements of 1.5 of EN 170000. Full details shall be

26、 given in the detail specification. 5 Ordering information The following ordering information shall be specified: 1) quantity; 2) EN or customer detail specification number, issue number and date; 3) nominal frequency expressed in MHz or GHz; 4) product code; 5) full description of any additional re

27、quirements. 6 Certified test records The detail specification shall state whether certified test records are required/not required in accordance with 2.12 of EN 170000. 7 Additional information (not for inspection purposes) The detail specification may include information (which is not normally requ

28、ired to be verified by the inspection procedure) such as circuit diagrams, curves, drawings and notes for the clarification of the detail specification. 8 Inspection requirements Clause numbers of tests and performance refer to EN 170000 and are given in Table 1. In this table D = destructive ND = n

29、on-destructive The manufacturer and their customers shall ensure that any quality aspects of the resonators to be supplied that are not covered by the maintenance of the capability approval programme are included in the detail specification. The blank detail specification does not include any period

30、ic tests as these are controlled by the CQC testing under the maintenance of the capability approval as defined in 3.11 and 3.12 of EN 170100.EN 170101:2001 - 6 - Table 1 Clause number and test D or ND Conditions of test Performance requirements 100% Inspection 3.3 Visual test 3.5.2 Insertion or att

31、enuation 3.5.3 ND 3.3 3.5.2 or 3.5.3 3.3 Specified values Group B inspection To be conducted on a sampling basis Sub-Group B1 3.4 Dimensions ND 3.4 Specified values- 7 - EN 170101:2001 Annex A (informative) Example front page layout for customer Detail Specifications not for publication Customer: Ma

32、nufacturer Specification reference Issue Number Date Page 1 of ELECTRONIC COMPONENTS OF ASSESSED (3) QUALITY BY CAPABILITY APPROVAL IN ACCORDANCE WITH: Manufacturers type number Outline and dimensions - (6) (first angle projection): Dimensions in mm(5) 1 Ratings (see 1.4 of EN 170000 for preferred r

33、atings). Operating temperature range Climatic category Mechanical test severitiesBS EN 170101:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Euro

34、pe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our produ

35、cts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers me

36、mbers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 70

37、01. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wi

38、de range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996

39、 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further infor

40、mation about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no

41、 extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such a

42、s symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.