BS EN 16776-2016 Resilient floor coverings Heterogeneous polyurethane floor coverings Specification《弹性地板覆盖物 异构聚氨酯地板覆盖物 规格》.pdf

《BS EN 16776-2016 Resilient floor coverings Heterogeneous polyurethane floor coverings Specification《弹性地板覆盖物 异构聚氨酯地板覆盖物 规格》.pdf》由会员分享，可在线阅读，更多相关《BS EN 16776-2016 Resilient floor coverings Heterogeneous polyurethane floor coverings Specification《弹性地板覆盖物 异构聚氨酯地板覆盖物 规格》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 16776:2016Resilient floor coverings Heterogeneous polyurethanefloor coverings SpecificationBS EN 16776:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16776:2016.The UK participation in its preparation was entrusted to Technic

2、alCommittee PRI/60, Resilient and Laminate Floor Coverings.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The Br

3、itish Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 86990 7ICS 97.150Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 March 20

4、16.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 16776:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16776 March 2016 ICS 97.150 English Version Resilient floor coverings - Heterogeneous polyurethane floor coverings - Specification Revtements de sol rsili

5、ents - Revtements htrognes en polyurthanne - Spcification Elastische Bodenbelge - Homogene und heterogene Polyurethan-Bodenbelge - Spezifikation This European Standard was approved by CEN on 10 January 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate th

6、e conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard

7、 exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the nationa

8、l standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak

9、ia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means

10、reserved worldwide for CEN national Members. Ref. No. EN 16776:2016 EBS EN 16776:2016EN 16776:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 5 4 Requirements . 5 5 Use and performance specification 6 6 Marking . 7 Annex A (normative) Metho

11、d for test for resistance to scratching 9 A.1 Introduction 9 A.2 Principle . 9 A.3 Apparatus and materials 9 A.4 Sampling and conditioning . 11 A.5 Procedure 11 A.6 Evaluation . 12 A.7 Report . 12 A.8 Calibration of steel pins . 12 A.8.1 General . 12 A.8.2 Procedure 12 A.8.3 Evaluation . 13 Annex B

12、(informative) Optional properties 14 Bibliography . 15 BS EN 16776:2016EN 16776:2016 (E) 3 European foreword This document (EN 16776:2016) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN. This European Sta

13、ndard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2016, and conflicting national standards shall be withdrawn at the latest by September 2016. Attention is drawn to the possibility that some of the element

14、s of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europ

15、ean Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov

16、enia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16776:2016EN 16776:2016 (E) 4 1 Scope This European Standard specifies the characteristics of heterogeneous resilient floor coverings based on polyurethane with thermosetting properties supplied in either roll, planks or tile for

17、m. This specification does apply for floor covering consisting of a wear layer and other compact layers made from polyurethane which differ in composition, chemical crosslinking and/or design and can contain a decor layer, reinforcement and other backing. This specification does not apply for floor

18、coverings that are specified in EN ISO 10582, EN ISO 24011, EN 1817 or EN 14565. To encourage the consumer to make an informed choice, the standard includes a classification system (see EN ISO 10874) based on intensity of use, which shows where these floor coverings should give satisfactory service.

19、 It also specifies requirements for marking. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of

20、 the referenced document (including any amendments) applies. EN 424, Resilient floor coverings Determination of the effect of simulated movement of a furniture leg EN 425, Resilient and laminate floor coverings Castor chair test EN 1471, Textile floor coverings Assessment of changes in appearance EN

21、 ISO 105-B02, Textiles Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fading lamp test (ISO 105-B02) EN ISO 291, Plastics Standard atmospheres for conditioning and testing (ISO 291) EN ISO 10874, Resilient, textile and laminate floor coverings Classification (ISO

22、10874) EN ISO 23997, Resilient floor coverings Determination of mass per unit area (ISO 23997) EN ISO 23999, Resilient floor coverings Determination of dimensional stability and curling after exposure to heat (ISO 23999) EN ISO 24340, Resilient floor coverings Determination of thickness of layers (I

23、SO 24340) EN ISO 24341, Resilient and textile floor coverings Determination of length, width and straightness of sheet (ISO 24341) EN ISO 24342, Resilient and textile floor-coverings Determination of side length, edge, straightness and squareness of tiles (ISO 24342) EN ISO 24343-1, Resilient and la

24、minate floor coverings Determination of indentation and residual indentation Part 1: Residual indentation (ISO 24343-1) EN ISO 24344, Resilient floor coverings Determination of flexibility and deflection (ISO 24344) EN ISO 24346, Resilient floor coverings Determination of overall thickness (ISO 2434

25、6) ISO 11378-1, Textile floor coverings Laboratory soiling tests Part 1: Kappasoil test BS EN 16776:2016EN 16776:2016 (E) 5 ISO 16581, Resilient and laminate floor coverings Determination of the effect of simulated movement of a furniture leg ASTM F1515, Standard Test Method for Measuring Light Stab

26、ility of Resilient Flooring by Color Change 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 wear layer layer of the floor covering directly exposed to wear Note 1 to entry: Binder content should be minimum 80 %. The binder content is consisti

27、ng of polyurethane resin. 3.2 scratch permanent, visible surface damage of a physical nature 4 Requirements The requirements and test methods for floor coverings made from polyurethane are illustrated in Table 1. Table 1 General requirements Characteristic Requirement Test method Roll form: length i

28、n m width in mm Not less than nominal values EN ISO 24341 Tiles: side length in mm Does not apply to planks squareness and straightness for side length: mm 400 mm 400 mm Deviation 0,15 % of nominal length up to 0,5 mm maximum Deviation allowed at any point 0,25 0,35 EN ISO 24342 Overall thickness in

29、 mm - averagea- individual results in mm - minimum overall thickness Nominal value + 0,13 - 0,10 Average valueb 0,15 1,20 mm EN ISO 24346 Total mass per unit area in g/m (average) Nominal value + 13 % - 10 % EN ISO 23997 Determination of thickness of layers Average of the wear layer thickness Nomina

30、l value + 30 % - 10 % and shall not exceed 0,03 mm EN ISO 24340 Residual indentation in mm 0,10 EN ISO 24343-1 BS EN 16776:2016EN 16776:2016 (E) 6 Dimensional stability after exposure to heat (expansion or shrinkage in %) 0,15 % EN ISO 23999 Effect of simulated movement of a furniture leg welded in

31、accordance with manufacturers instructions: no damage shall be visible with foot Type 0 (32 kg) ISO 16581 EN 424 Curling after exposure to heat Rolls and tiles (intended for welding) Tiles (intended for unwelded laying) 8 mm 2 mm EN ISO 23999 Flexibility Test using a 20 mm mandrel. For products whic

32、h show signs of cracking, perform a further test using a 50 mm mandrel. If results show no further cracking, record the use of a 50 mm mandrel. EN ISO 24344 Method A Evaluation in respect to occurrence of scratches The load which the first uninterrupted scratches cause on the surface shall be record

33、ed (visible to the naked eye) Annex A Colour fastness to artificial light 6 minimum or AE 8 after 300 h, where E is the irradiance, expressed in watts per square meter EN ISO 105-B02 Method 3cASTM F1515 Suitability for castor chair use After 25 000 cycles, no delamination shall occur. No disturbance

34、 to the surface other than a slight change in appearance EN 425 aAverage value of the measured values. bAverage value of the results of the specimens. cA full sized test specimen shall be exposed. A further test specimen shall be stored in the dark, which will further serve as a reference standard f

35、or evaluation of the colour change. 5 Use and performance specification The classification scheme for resilient floor coverings is described in EN ISO 10874. The requirements for heterogeneous polyurethane floor coverings in accordance with this scheme are specified in Table 2. BS EN 16776:2016EN 16

36、776:2016 (E) 7 Table 2 Classification requirements Class Test method 21 22 23 Symbol EN ISO 10874 Level of Use Domestic moderate Domestic general Domestic heavy Furniture leg ISO 16581 EN 424 Type 3 Type 3 Type 3 Scratch resistance in N Annex A 3 3 3 Thickness of wear layer EN ISO 24340 0,10 mm 0,10

37、 mm 0,15 mm Class Test method 31 32 33 34 Symbol EN ISO 10874 Level of Use Commercial moderate Commercial general Commercial heavy Commercial very heavy Furniture leg ISO 16581 EN 424 Type 3 Type 2 Type 2 Type 2 Scratch resistance in N Annex A 5 5 6 6 Thickness of wear layer EN ISO 24340 0,15 mm 0,1

38、5 mm 0,20 mm 0,20 mm Class Test method 41 42 43 Symbol EN ISO 10874 Level of Use Light industrial moderate Light industrial general Light industrial heavy Furniture leg ISO 16581 EN 424 Type 2 Type 2 Type 2 Scratch resistance in N Annex A 6 7 7 Thickness of wear layer EN ISO 24340 0,20 mm 0,20 mm 0,

39、20 mm 6 Marking Floor coverings that are covered by this standard and/or their packaging shall bear the following marking: a) number and date of this European standard, i.e EN 16776:2016; BS EN 16776:2016EN 16776:2016 (E) 8 b) manufacturers or suppliers identification; c) product name; d) colour/pat

40、tern and number batch and, if applicable, roll/package number; e) applicable classes/symbols of the product; f) for rolls: the length, width and thickness; g) for tiles: the dimensions of a tile and the area in square metres contained in a package. BS EN 16776:2016EN 16776:2016 (E) 9 Annex A (normat

41、ive) Method for test for resistance to scratching A.1 Introduction This method of test specifies a procedure to assess the appearance of scratches on resilient floor covering surfaces under laboratory conditions. A.2 Principle A test piece mounted on a horizontal rotating plate is scratched by a def

42、ined steel pin. The pin can be loaded with different weights. The load at which the pin causes an uninterrupted scratch of defined characteristics is used for the ranking of the product. A.3 Apparatus and materials NOTE The item numbers in parentheses in A.3.1.1 to A.3.1.6 refer to Figure A.1. A.3.1

43、 Scratch tester (Figure A.1), consisting of A.3.1.1 to A.3.1.6 A.3.1.1 Stand with a device to indicate the horizontal, e.g. a spirit level A.3.1.2 Turntable (4) freely rotating, motor-driven, for supporting the test piece, rotating around its vertical axis at (35 5) mm per second at the position whe

44、re the scratch is made A.3.1.3 Clamping disc (6) to keep the test specimen flat A.3.1.4 Arm (5) with a holder for the steel pin (3), mounted on a ball bearing, with horizontal axis. This arm is engraved with a scale (1) and is made adjustable in order to ensure that it is always horizontal, independ

45、ent of the thickness of the test piece, when the steel pin touches the surface of the specimen. A.3.1.5 Movable weight (2) that can be moved along the arm (5) The mass of the weight together with the effective mass of the arm presses the steel pin onto the surface to be tested. The force exerted on

46、the steel pin shall be accurate to 0,01 N, when measured at the mounting device for the pin. A.3.1.6 Steel pin (3) (also shown in Figure A.2), made from tungsten carbidecobalt (WCCo) hard metal, HIP treated (hot isostatic pressed). The steel pin shall have a diameter of 3 mm 0,02 mm. The conical tip

47、 shall have a diameter of 0,5 mm 0,02 mm and an angle of 45 1, as indicated in Figure A.2. BS EN 16776:2016EN 16776:2016 (E) 10 A.3.2 Soil B021)according to ISO 11378-1, consisting of: 37,80 % peat dust; 17,45 % Portland Cement; 17,70 % kaolin; 17,70 % quartz; 6,20 % Nujol mineral oil 014; 1,05 % du

48、st wfk 09 X; 0,60 % ferric oxide black; 1,50 % ferric oxide yellow. Key 1 adjustable scale 2 movable weight 3 steel pin 4 turntable 5 arm 6 clamping disc Figure A.1 Example of a type of apparatus for the determination of resistance to scratching 1) Forschungsinstitut fr Reinigungstechnologie, Adlers

49、trae 42, D-47798 KREFELD, Germany, supply soil to this specification commercially. This information is given for the convenience of users of this European Standard and does not constitute an endorsement by CEN of their product. Equivalent products may be used if they can be shown to lead to the same results. BS EN 16776:2016EN 16776:2016 (E) 11 Dimensions in millimetres unless indicated otherwise Key Pin diameter: 0,3mm