BS EN 16256-4-2012 Pyrotechnic articles Theatrical pyrotechnic articles Minimum labelling requirements and instructions for use《烟火制品 戏剧烟火制品 使用中的最低标签要求和说明书》.pdf

《BS EN 16256-4-2012 Pyrotechnic articles Theatrical pyrotechnic articles Minimum labelling requirements and instructions for use《烟火制品 戏剧烟火制品 使用中的最低标签要求和说明书》.pdf》由会员分享，可在线阅读，更多相关《BS EN 16256-4-2012 Pyrotechnic articles Theatrical pyrotechnic articles Minimum labelling requirements and instructions for use《烟火制品 戏剧烟火制品 使用中的最低标签要求和说明书》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16256-4:2012Pyrotechnic articles Theatrical pyrotechnic articlesPart 4: Minimum labelling requirements and instructions for useCopyright European Committee for Standardizat

2、ion Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16256-4:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16256-4:2012. The UK participation in its preparation was entrusted to

3、 Technical Committee CII/47, Pyrotechnic articles.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British

4、Standards Institution 2013. Published by BSI Standards Limited 2013.ISBN 978 0 580 74212 5 ICS 71.100.30 Compliance with a British Standard cannot confer immunityfrom legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 Februa

5、ry 2013.Amendments issued since publicationDate Text affectedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16256-4:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM E

6、N 16256-4 December 2012 ICS 71.100.30 English Version Pyrotechnic articles - Theatrical pyrotechnic articles - Part 4: Minimum labelling requirements and instructions for use Articles pyrotechniques - Articles pyrotechniques destins au thtre - Partie 4: Exigences dtiquetage minimal et mode demploi P

7、yrotechnische Gegenstnde - Pyrotechnische Gegenstnde fr Bhne und Theater - Teil 4: Mindestanforderungen an die Kennzeichnung und Gebrauchsanweisung This European Standard was approved by CEN on 3 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

8、 the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Stand

9、ard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the nati

10、onal standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slo

11、vakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved

12、worldwide for CEN national Members. Ref. No. EN 16256-4:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16256-4:2012EN 16256-4:2012 (E) 2 Contents Page Foreword 31 S

13、cope 42 Normative references 43 Terms and definitions .44 Minimum labelling requirements 44.1 General 44.2 Details of manufacturer or importer 44.3 Name and type of article .44.4 Category and registration number .54.5 Net explosive content 54.6 Printing .54.7 Marking of very small items 54.8 Minimum

14、 Age limits and Safety Distances .54.9 Identification number of the notified body 54.10 Instructions for use, safety and disposal information .65 Category T1 Articles 66 Category T2 Articles 6Annex A (normative) List of mandatory and optional parameters and corresponding codes .9Annex B (informative

15、) Overview of essential safety requirements and corresponding clauses of all parts of this European Standard 10Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2007/23/EC on the placing on the market of pyrotechnic articles . 11Bibliog

16、raphy . 12Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16256-4:2012EN 16256-4:2012 (E) 3 Foreword This document (EN 16256-4:2012) has been prepared by Technical Committe

17、e CEN/TC 212 “Pyrotechnic articles”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at th

18、e latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by

19、 the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This European Standard is one of the series of standards as listed be

20、low: EN 16256-1, Pyrotechnic articles Theatrical pyrotechnic articles Part 1: Terminology EN 16256-2, Pyrotechnic articles Theatrical pyrotechnic articles Part 2: Categories of theatrical pyrotechnic articles EN 16256-3, Pyrotechnic articles Theatrical pyrotechnic articles Part 3: Requirements for c

21、onstruction and performance EN 16256-4, Pyrotechnic articles Theatrical pyrotechnic articles Part 4: Minimum labelling requirements and instructions for use EN 16256-5, Pyrotechnic articles Theatrical pyrotechnic articles Part 5: Test methods CEN/TC 212 has also developed European Standards for: Pyr

22、otechnic articles Fireworks Categories 1, 2 and 3 Pyrotechnic articles Fireworks, Category 4 Pyrotechnic articles Pyrotechnic articles for vehicles Pyrotechnic articles Other pyrotechnic articles According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following

23、 countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norwa

24、y, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16256-4:2012EN

25、16256-4:2012 (E) 4 1 Scope This European Standard specifies minimum labelling requirements for the article and primary packaging and for the instructions for use of theatrical pyrotechnic articles of the generic types defined in EN 16256-1:2012, Clause 3. 2 Normative references The following documen

26、ts, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 16256-1:2012, Pyrotechnic

27、 articles Theatrical pyrotechnic articles Part 1: Terminology EN 16256-3:2012, Pyrotechnic articles Theatrical pyrotechnic articles Part 3: Requirements for construction and performance EN 16256-5:2012, Pyrotechnic articles Theatrical pyrotechnic articles Part 5: Test methods 3 Terms and definitions

28、 For the purposes of this document, the terms and definitions given in EN 16256-1:2012 apply. 4 Minimum labelling requirements 4.1 General Theatrical pyrotechnic articles shall be marked with the minimum information specified in 4.2 to 4.10. This does not exclude the possibility of adding supplement

29、ary information on the label on a national basis. The specified information shall be given in the official language(s) of the country in which the articles or primary packs are offered for sale. For each language, it shall be presented as a whole and shall not be interrupted by other text. Additiona

30、l text given in another language shall not conflict with the specified information. 4.2 Details of manufacturer or importer Labelling shall include the name and address of the manufacturer. The address shall comprise at least the town and the country. If the manufacturer is not established in the Eu

31、ropean Union, the labelling shall include the name of the manufacturer and the name and address of the importer. The address shall comprise at least the town and the country. 4.3 Name and type of article Labels are to be provided directly on the article (or on the smallest piece of packaging if the

32、article does not provide sufficient space for the labelling requirements) and will include the following information: The word “ Pyrotechnic“ shall be marked on the label. The type of article shall be marked, in upper case, in conformity with the generic types of EN 16256-1:2012, Table 1, in singula

33、r form. EXAMPLE “Pyrotechnic 10 second FOUNTAIN red/green” Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16256-4:2012EN 16256-4:2012 (E) 5 If a trade name is used in addi

34、tion to the type name, it shall not conflict with the principal effects of the relevant type of article or with the name of another generic type of article. 4.4 Category and registration number The registration number for tracing products shall be marked in bold in accordance with the example below:

35、 XXXX - YY - ZZZZ. where XXXX refers to the registration number of the notified body issuing the EC-Type examination certificate, YY refers to the category of article in abbreviated format (T1 or T2, respectively) and where ZZZZ. is a processing number given by the notified body. 4.5 Net explosive c

36、ontent The labelling shall include the net explosive content of the article. The abbreviation for the net explosive content (NEC) may be used. 4.6 Printing Labelling shall be clearly visible, easily legible, indelible and on a contrasting background. Printing errors, which are not misleading, are no

37、t classified as faults. When measured in accordance with EN 16256-5:2012, 6.6, the type sizes shall be such that the height of the character X (in upper case) is at least 2,1 mm. The minimum height of the CE-marking shall be 5 mm. 4.7 Marking of very small items If the article does not provide enoug

38、h space to carry all the specified information, the manufacturer or importer shall provide at least the following information on the article (for example attached to the wire): CE-marking followed by the identification number of the notified body (see 4.9) registration number (see 4.4); the word “ P

39、yrotechnic“ and the generic type (see 4.3). Additionally, all information required by this European Standard shall be provided on the smallest piece of packaging. Where the information printed on the primary pack might be affected by the opening of the pack, the manufacturer will ensure that the pac

40、k design prevents loss of information when the label is broken. 4.8 Minimum Age limits and Safety Distances Minimum age limits and safety distance parameters are specified in Clause 5 for T1 products and Clause 6 for T2 products. 4.9 Identification number of the notified body CE-marking shall be fol

41、lowed by the identification number of the Notified Body responsible for: monitoring the existing quality system in case of Modules D, E according to Directive 2007/23/EC and/or checking conformity to type according to Module C according to Directive 2007/23/EC. Copyright European Committee for Stand

42、ardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16256-4:2012EN 16256-4:2012 (E) 6 4.10 Instructions for use, safety and disposal information Safety information shall be emphasised by use of a heading, or bold t

43、ype, or similar. If the article or smallest piece of packaging is not labelled with the required information then the article or smallest piece of packaging shall be labelled with the sentence “User must read and follow the instructions enclosed given by the manufacturer”, emphasised by use of a hea

44、ding, or bold type, or similar. The manufacturer shall provide “Instructions for use“ with the article. These shall include the following information: operating instructions for safe functioning; misfire procedures; storage and handling procedures; disposal procedures. 5 Category T1 Articles The min

45、imum age limits applicable in the country in which the article is offered for retail sale shall be clearly stated on the label. The minimum age limit of 18 years applies, if the individual Member State has not raised or lowered these age limits according to Directive 2007/23/EC Art. 7 (2). The minim

46、um safety distance(s) shall be placed in a text box using the following phrases: Minimum safety distance in direction of the effect and Minimum radial safety distance or Minimum safety distance. And where applicable according to Table 1 and Table 3 of EN 16256-3:2012, the phrase “FOR OUTDOOR USE ONL

47、Y” shall be stated in upper case on the label in the text box. Additional information from Table A.1 may be stated and shall follow the same format as the mandatory information. This information shall be separate from the textbox containing the mandatory parameters. 6 Category T2 Articles “For use o

48、nly by persons with specialist knowledge“ shall be stated on the label. For every generic type the following information shall be indicated: effect distance (denoted by A); sound pressure level including the measuring distance (denoted by B); the hazardous debris distance (denoted by C); information on incandescent particles returning to the level from which the device was fired (denoted by D); and radial effect distance (denoted by T). The above mentioned information is necessary for calculating the minimum safety distanc